® 5200WHC2 Wiser Home Controller 2 Installation Instructions Thank you for your purchase of the Wiser Home Controller 2. This installation document provides the configuration information needed to set up the product. Use this document in conjunction with the Setup Sheet (provided with the Wiser) and the Help files included in the software products from Schneider Electric. Be sure to follow all safety information included in the documents and on the product. © 2013 Schneider Electric. All Rights Reserved.
5200WHC2 Wiser Home Controller 2 Installation Instructions Contents Safety Notice ........................................................................................................... 3 Introduction ............................................................................................................ 4 Product Features ............................................................................................. 5 Indicator LEDs ..................................................................
5200WHC2 Wiser Home Controller 2 Installation Instructions Safety Notice The Wiser Home Controller 2 (Wiser 2) is designed for indoor use in residences and businesses. The Wiser 2 operates continuously over long periods without attention from the user. Therefore, it is important to install and locate the equipment where it will be protected from heat, dust, moisture and physical damage.
5200WHC2 Wiser Home Controller 2 Installation Instructions Introduction Thank you for purchasing the Wiser Home Controller 2, catalogue number: 5200WHC2. The Wiser 2 controller provides a central point for managing many electrical and electronic devices in your home or business. The Wiser 2 product is a (1) controller device and (2) Graphical User Interface (GUI) software: • Wiser Home Controller 2 (Wiser 2).
200WHC2 Wiser Home Controller 2 Installation Instructions Product Features The Wiser Home Controller 2 (Wiser 2) includes firmware and documentation. The most recent versions of the configuration software packages are downloaded from the Internet. Product Number 5200WHC2 Description Wiser Home Controller 2, interface unit for local and remote monitoring and control of electrical devices. Includes controller, power supply, battery, C-Bus connector plug and a network patch cord.
5200WHC2 Wiser Home Controller 2 Installation Instructions The Wiser 2 is configured by the installer using software tools. There are no controls or switches that require user attention. With the exception of the Power LED, the front panel LED indicators can be turned off by the installer, if desired. The system connections are made at the back panel of the Wiser 2. Your installation might not use all of the available ports. The figure below shows the location of the indicators and ports on the Wiser 2.
5200WHC2 Wiser Home Controller 2 Installation Instructions Top Cover Removal and USB port for an Optional ZigBee Adapter To remove the top cover, (1) press the release tabs on the rear panel and then (2) lift the cover. The USB Zigbee Interface (UZI) is and optional feature. Refer to the instructions included with the UZI. 2. Lift top cover 1. Press tabs from below UZI port (USB) Battery Location The battery is located on the underside of the Wiser 2.
5200WHC2 Wiser Home Controller 2 Installation Instructions Indicator LEDs The operation of the LEDs is shown in the table below. Symbol C-Bus MRA LED Name Operation Power On when power is applied to the unit using the supplied AC/DC power supply or Power Over Enternet (PoE) when connected to the appropriate power source; 802.3af PoE device. C-Bus Yellow (green+red) = initializing (e.g.
5200WHC2 Wiser Home Controller 2 Installation Instructions Installation The Wiser Home Controller 2 must be programmed by a competent installer before the control and monitoring functions are available! Download the Required Software Tools The software applications for Wiser 2 (C-Bus Toolkit, Zoolkit and PICED) from Schneider Electric can be freely downloaded from the Clipsal. com CIS portal: http://www.clipsal.
5200WHC2 Wiser Home Controller 2 Installation Instructions The following table lists the software programs from Schneider Electric that are applicable to the Wiser Home Controller 2 Software Product Purpose Rev. Level Wiser 2 Software Operational software supporting the Wiser features and user interface. Installed at the factory C-Bus Toolkit Software Configures the C-Bus network and creates project files that are used by PICED.
5200WHC2 Wiser Home Controller 2 Installation Instructions Security It is very important to set proper levels of security to protect the unit from unauthorised persons. In applications that use Wi-Fi and Remote Access functions, use these recommendations: • Use Secure Wireless Access • Use WPA2 Personal Security Settings • Leave Toolkit and Projector Updates disabled by default (enable them only on an as-required basis). • Define a unique User and Password for projects. Do not use the default...
5200WHC2 Wiser Home Controller 2 Installation Instructions Set Up the PC for Configuration Tasks You need a PC to configure a Wiser Home Controller. 2 After the configuration tasks are done, you may disconnect the PC from the network, if desired. Refer to Figure 4 in the Setup Sheet for cable connections. At this time the PC must have the following characteristics: • Windows operating system, i.e., XP, Windows 7, Vista.
5200WHC2 Wiser Home Controller 2 Installation Instructions ZigBee Network Devices You can connect to an existing ZigBee network and have the ability to control devices using the Wiser 2’s GUI. Use one of the following interface adapters to provide the wireless connection. Catalogue Product Name Description 5200UZI USB ZB Interface Unit Interface adapter between PC or Wiser 2 to an existing ZigBee network. Allows connection in easy mode and is used with Zoolkit configuration software.
5200WHC2 Wiser Home Controller 2 Installation Instructions C-Bus Network Devices In order to collect C-Bus network information (for PICED), the Wiser 2 must be connected to an active C-Bus network. Be sure to use Cat.5e UTP cable that is certified for use on C-Bus networks; catalogue number 5005C305B (solid), 5005C305BST (stranded). The Wiser 2 uses a 2-terminal plug for C-Bus. This avoids the possibility of wiring the C-Bus network to the Ethernet LAN.
5200WHC2 Wiser Home Controller 2 Installation Instructions PICED Software Recommendations Be sure to follow the programming steps given earlier to map your existing network. During the PICED programming session, the following actions are recommended: Action or Topic Recommendations Select or De-select C-Bus If you are not using C-Bus devices, de-select C-Bus. PICED will use a placeholder project file. In the future, you can add a C-Bus project. If you are using C-Bus, select the option.
5200WHC2 Wiser Home Controller 2 Installation Instructions Using the HDMI Interface The installer can create a user profile that allows the end user to access the GUI using a digital receiver and its remote control. If the HDMI interface will be used, the distance between the Wiser 2 and the digital receiver will be limited by the length of the HDMI cable. The HDMI interface is active when the Wiser 2 is operating in normal mode.
5200WHC2 Wiser Home Controller 2 Installation Instructions Using a Wireless LAN The Wiser 2 supports 802.11 bgn wireless in the 2.4 GHz frequency range. Some installations might use the Wi-Fi LAN for one or more of the following reasons: • The user wishes to use the HDMI interface and must place the Wiser 2 close to the digital receiver. • The customer’s ADSL modem might be in a location where running a cable from the modem to the Wiser 2 is not practical.
5200WHC2 Wiser Home Controller 2 Installation Instructions Setting Up Port Forwarding The screen below is a representation of how your modem /router (not the Wiser 2) should be configured to support access to the Wiser 2 from the Internet. Note: This setup does not apply if you are using a bridged Modem or have configured your modem/router to work as a bridged modem. Port Definitions for the Wiser 2 To use the Port Definitions refer to the table.
5200WHC2 Wiser Home Controller 2 Installation Instructions To maintain an ongoing connection to your Wiser 2, you should use either a Fixed IP address for the LAN interface of the Wiser 2, or alternately setup your Modem/Router to always provide the same IP Address to the Wiser 2 (refer to your modem/router manual for further details on how to do this). The Wiser 2’s CNI Port is configurable; the default port address is 10001 (to match toolkit defaults).
5200WHC2 Wiser Home Controller 2 Installation Instructions Troubleshooting If you are having problems with your Wiser 2, try the basic diagnostic steps first. Basic Problem Diagnosis Step Action Identify and Document Make notes about any error messages or LED error conditions. If there is a problem with other equipment it could affect the Wiser 2. This is very important if you have to explain the problem to support personnel.
5200WHC2 Wiser Home Controller 2 Installation Instructions Additional Information Useful DOS Command Prompt Programs The two DOS programs illustrated here use command lines. These programs can be useful to diagnose some connectivity problems and gather information about IP addresses. Go to Start/Run and then type: cmd.exe then click OK type: ipconfig /all and press Enter cmd.
5200WHC2 Wiser Home Controller 2 Installation Instructions Terms Used in This Document • Customer’s modem The hardware component connecting the Wiser Home Controller to the Internet. • Default gateway A network node, for example a router, that serves as an access point to another network. • DHCP Dynamic Host Configuration Protocol. A protocol that assigns IP addresses to client stations on a network at startup.
5200WHC2 Wiser Home Controller 2 Installation Instructions Specifications The Wiser Home Controller 2 is designed as an interface device for monitoring and controlling lights and other devices in residential and commercial locations. Parameter Value Catalogue Number 5200WHC2 Device Information Technology Equipment, Class 2 Location Indoors only LAN Connectivity Wired: Cat5e Wireless: 802.11 bgn Wireless frequency 2.4 GHz Radio frequency power Less than 100mW Power supply Adaptor: 24Vd.c. 1.
5200WHC2 Wiser Home Controller 2 Installation Instructions 175mm 33.5mm 219mm Allow 25mm (1 inch) space above and to the sides of the Wiser 2 to provide for adequate ventilation. 24 of 30 © 2013 Schneider Electric. All Rights Reserved.
5200WHC2 Wiser Home Controller 2 Installation Instructions Standards Complied Declarations of Conformity Australian/New Zealand EMC & Electrical Safety Frameworks and Standards Regulation Standard Title Radio Communications AS/NZS 4268 Radio Equipment and Systems-Short Range Devices EMC AS/NZS CISPR22 Information Technology Equipment-RF emissions European Council Directives and Standards Directive Standard Title EMC Directive 2004/108/EC CISPR 22,EN 55022 Information Technology Equipment-RF
5200WHC2 Wiser Home Controller 2 Installation Instructions U.S. FCC Regulations CFR Title 47 Part 15, Subpart B and Subpart C FCC ID: WZCWHC25918 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation.
5200WHC2 Wiser Home Controller 2 Installation Instructions GNU General Public Licence The software included in this product contains copyrighted software that is licensed under the GNU GENERAL PUBLIC LICENSE Version 2, June 1991. You may obtain the complete Corresponding Source code from Clipsal for a period of three years after our last shipment of this product. Contact Schneider Electric for details.
5200WHC2 Wiser Home Controller 2 Installation Instructions 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
5200WHC2 Wiser Home Controller 2 Installation Instructions 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7.
Warranty Statement The Wiser Home Controller 2 carries a two-year warranty against manufacturing defects. Warranty Statement The benefits conferred herein are in addition to, and in no way shall be deemed to derogate; either expressly or by implication, any or all other rights and remedies in respect to the Schneider Electric product, which the consumer has in the location where the product is sold. The warrantor is Schneider Electric.