C-Bus™ RF Wireless Key Fob and Visor Remote SLC5800TXBDKF and SLC5800TXBDVR for use with RF Wireless Control Systems Instruction Bulletin Retain for future use.
C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin 63249-420-342A1 06/2010 HAZARD CATEGORIES AND SPECIAL SYMBOLS Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this bulletin or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
63249-420-342A1 06/2010 C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin PLEASE NOTE Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. This document is not intended as an instruction manual for untrained persons. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this manual. FCC CLASS B This device complies with Part 15 of the FCC Rules.
C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin 63249-420-342A1 06/2010 ABOUT THE RF KEY FOB AND VISOR REMOTE The C-Bus™ Wireless RF Key Fob and Visor Remote provides C-Bus protocol commands to remotely controlled buttons on RF wireless wall units and plug adapter units. The two radio frequency (RF) remote controls work up to 50 to 70 feet (15 to 20 meters) from a unit they control.
63249-420-342A1 06/2010 C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin INSTALLING THE BATTERIES Battery Tips and Precautions Use new CR2032 batteries and verify that all batteries are the same type. Keep batteries out of the reach of children. Verify that the positive (+) and negative (–) battery polarities line up with the battery-case polarities. Replace batteries that have been in use two or more years. Recycle or properly dispose of used batteries.
C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin 63249-420-342A1 06/2010 Key Fob Battery Installation 1. Using a small flat-head screw driver, gently pry off the bottom of the key fob. 2. Remove the old battery from the key fob. 3. Insert the new battery. Verify that the positive and negative terminals match the symbols inside the battery compartment. 4. Replace the back cover by positioning the cover and snapping it into place.
63249-420-342A1 06/2010 C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin Visor Remote Battery Installation 1. Using a small Phillips screw driver, remove the two screws from the back of the visor remote. 2. Remove the back of the visor remote. 3. Remove the old battery from the visor remote. 4. Insert the new battery. Verify that the positive and negative terminals match the symbols inside the battery compartment. 5.
C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin 63249-420-342A1 06/2010 PROGRAMMING THE KEY FOB Follow the guidelines below to make the Key Fob functional. Program C-Bus Wireless units to recognize the key fob's buttons. Program the key fob, wall units, and plug adapter units using learn mode. Learn mode is activated on the remote by removing the back cover (see the "Installing the Batteries" section to remove the back cover), and sliding the switch down to the Learn position.
63249-420-342A1 06/2010 C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin PROGRAMMING THE VISOR REMOTE Follow the guidelines below to make the Visor Remote functional. Program C-Bus Wireless units to recognize the visor remote's buttons. Program the visor remote, wall units, and plug adapter units using learn mode.
C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin 63249-420-342A1 06/2010 CLEARING REMOTE ASSIGNMENTS To clear an individual remote assignment learned by a specific button on a wall unit or plug adapter unit, reassign the same remote button to the wall unit or plug adapter button. Assigning a button once programs it. Assigning it again clears it. To clear all remote assignments (from all remote controls) learned by an individual wall unit or plug adapter unit: 1.
63249-420-342A1 06/2010 C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin SPECIFICATIONS Parameter Description Supply voltage CR2032 batteries Radio frequency 916 MHz Transmitting power 10 mW Wood frame / brick veneer construction Typical range (range depends on building construction and the 50 to 70 feet (15 to 20 m) proximity to dense or metallic Brick, stone, or steel frame construction objects) 35 to 50 feet (10 to 15 m) Steel reinforced concrete construction 20 to 35 feet (5 to
C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin 63249-420-342A1 06/2010 DIMENSIONS Figure 3: Key Fob Dimensions Figure 4: Visor Remote Dimensions 12 © 2010 Schneider Electric. All Rights Reserved.
63249-420-342A1 06/2010 C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin STANDARDS The key fob and visor remote complies with the following Standards: Table 2: U.S. and Canadian Product Safety Standards and U.S. FCC Regulations Standards/Regulations FCC Part 15 © 2010 Schneider Electric. All Rights Reserved.
C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin 14 63249-420-342A1 06/2010 © 2010 Schneider Electric. All Rights Reserved.
63249-420-342A1 06/2010 © 2010 Schneider Electric. All Rights Reserved.
C-Bus™ RF Wireless Key Fob and Visor Remote Instruction Bulletin SUPPORT AND SERVICE Contact the Customer Information Center for technical support by phone at 1-888-778-2733 or e-mail at lightingcontrol.support@us.schneider-electric.com. Contact your local Schneider Electric service representative or C-Bus™ system certified installer for repairs or service to your network. You may also find helpful information on our web site at www.Schneider-Electric.us.