Installation Manual

ManualsBrandsSchneider Electric ManualsElectronicsZ-WAVE+ SWITCH SINGLE POLE

Instruction Bulletin SQR14102**Z Z-Wave Plus Switch

SQR14102**Z Z-Wave

Plus Switch

** = color code: WH (white), LA (light almond), BK (black), GY (gray)

Features

• Wireless Z-Wave technology creates a mesh network for command and control

interoperability with other Z-Wave compliant controllers and devices.

• Manual and remote ON/OFF control of any connected lighting and other

electrical load.

• Programmable delayed OFF time.

• 3 configurable “power ON state”.

• Configurable child lockout feature which disables local control.

• Support single pole or 3-way (multi-location) use.

• Measure the energy usage of the connected loading, display the actual

consumption (in W) and the accumulated power used (in kWh) in the user

interface of the gateway.

NOTE:

• Power on state means the initial status of the device when it is powered on.

• For multi-location applications, the traditional mechanical switch or Z-Wave

wireless auxiliary switch SQR50101**Z could be used along with one Z-

Wave Master Switch.

• Please refer to the gateway installation manual for energy usage display

and energy measurement features.

Specification of SQR14102**Z Z-Wave Plus Switch, Single Pole, Energy Monitoring

Voltage

120 Vac, 60 Hz

Incandescent

1000 W

LED

5 A

Standard ballast

1200 Va

Resistive

1800 W (15 A)

Motor

1/2 Hp

Operating temperature

32–104°F (0–40°C)

Supply connection

14 AWG

Wireless type

Z-Wave (Support S2 and SmartStart)

Wireless frequency

908.40 MHz / 908.42 MHz / 916 MHz

Suitable for at least 90°C.

Instruction Bulletin

GDE77982_Eng,

Summary of content (8 pages)

PAGE 1
Instruction Bulletin SQR14102**Z Z-Wave Plus Switch Instruction Bulletin GDE77982_Eng, SQR14102**Z Z-WaveTM Plus Switch ** = color code: WH (white), LA (light almond), BK (black), GY (gray) Features • • Wireless Z-Wave technology creates a mesh network for command and control interoperability with other Z-Wave compliant controllers and devices. Manual and remote ON/OFF control of any connected lighting and other electrical load. • Programmable delayed OFF time. • 3 configurable “power ON state”.
PAGE 2
Instruction Bulletin SQR14102**Z Z-Wave Plus Switch Precautions CAUTION HAZARD OF UNINTENDED USE This device is intended to be used for non-critical automation activities. It is not intended to support life, safety, or medical equipment. Failure to follow these instructions can result in personal injury or equipment damage. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH • Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices.
PAGE 3
Instruction Bulletin SQR14102**Z Z-Wave Plus Switch Notice Wireless Range Conditions The wireless range is the effective distance of remote control and it will be impacted by the following conditions: • Each wall or obstacle (e.g., refrigerator, TV, etc.) between the remote or ZWave device and the destination device will reduce the wireless range. • Brick, tile, or concrete walls block more of the wireless signal than walls made of wooden studs and plasterboard (drywall).
PAGE 4
Instruction Bulletin SQR14102**Z Z-Wave Plus Switch (change the CR No.
PAGE 5
Instruction Bulletin SQR14102**Z Z-Wave Plus Switch Operation 1. Local control: One short tap on upper paddle: turn on the lighting One short tap on lower paddle: turn off the lighting (update the switch drawing by adding the reset button, remove unnecessary marking) 2. Group control the nodes of association group 2: Press upper and lower paddles at the same time for group on and group off.
PAGE 6
Instruction Bulletin SQR14102**Z Z-Wave Plus Switch A. SmartStart inclusion: The feature assumes the gateway has implemented SmartStart. Users could use the APP of the gateway or the gateway camera to scan the QR code on device or on device package before powering on the device, and then when the device is powered on, it shall be automatically added to the gateway. B.
PAGE 7
Instruction Bulletin SQR14102**Z Z-Wave Plus Switch Configuration Parameter No. Size Description Valid Value Default Value Unit 1 1 byte Synchronization of 0 = Power ON, LED OFF load power and LED Power OFF, LED ON 1 indicator 1 = Power ON, LED ON Power OFF, LED OFF 2 1 byte Delay Off Time 0~240 0 second 3 1 byte Power On Status 1 = Off 2 = On (full brightness) 3 = Last state 1 N/A 4 1 byte Child Lockout 0= Disable 1= Enable 0 N/A N/A Association Grouping ID Max. No.
PAGE 8
Instruction Bulletin SQR14102**Z Z-Wave Plus Switch -Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.