69-1009 CHIME Doors CHIME Special Motion LIGHTS Time Activated LIGHTS Sensor Activated " Home Control Use these buttons to turn on lights and chimes. Activates or deactivates sensors designated “special chime” whenever the designated sensor is activated. This designation means you want to sound a chime when that sensor is activated, Outdoor motion sensors are the most commonly designated special chime. IMPORTANT: Sensors named “Special Chime” do not cause the alarm siren {o go off.
Tools Needed Sensor Activated Entry/Exit Delay Activated Time Activated Example . 69-1009 To complete the planning instructions, you need the following: + Pencil + Adhesive notes + Sensor Planning chart » Light Control Planning chart + Option Planning chart + Sensors * X10 Modules * Sensor-activated lights and appliances respond to sensor signals. For example, a light goes on when someone walks past a motion sensor or opens a closet door. The light turns off after 4 minutes.
69-1009 To plan sensors: Sensor Planning 1. List the sensors you have in column 1 as shown jn Fig. 19. Do not include the control panel. 2. Write down where each sensor should 80 in column 2. 3. Select a location name for each sensor from Table 1 and write it on your Sensor Planning chart. 4. Write the home location from the second column on adhesive notes and label each sensor. Then, when you install sensors on doors and windows, you'll know where to put each one.
Before you begin: To plan lights: 68-1009 Planning Light Contort Set the housecoat on all the X-10 Modules to the same letter. If you are using an X-10 Siren, set the siren module house code to the next higher letter. Use a small screwdriver to turn the dials. 1. Set the X-10 Module unit numbers consecutively. Turn the numbered dial on the X-10 Module to the desired number, Be sure to select the correct X-10 Module for the device. Do not use a lamp module to control appliances. 2.
69-1008 . you want the system to call. You can program one 18-digit number for each option. If you don‘t have touch-tone service, enter a 0 before the phone number. Option 5: AC Power Failure Tum this option on if you want the panel to call when the power goes out. Option 6: Latchkey When the Latchkey option is turned on, the pane calls you if the system has not been disarmed by a certain time. For example, you can have the panel call if your children haven't disarmed the system by 3 p.m.
9-1009 POWER-U’ If you have many sensors and lights to program, power up your control panel near a table or desk where you can be organized and comfortable while you work. When you've finished programming, you can move the panel to its permanent location. 1. Open the cover and install the battery. 9 Volt Battery Fig. 22. Installing the battery. 2. Plug the transformer into an switched outlet. IMPORTANT: An unscheduled outlet is not connected to a wall switch.
69-1008 PROGRAMMING THE SYSTEM Program sensors before vou install them. The panel recognizes a sensor when you press the sensor’s Program button. NOTE: You will not be able to control lights or appliances unless you bought X-10 Lamp and Appliance Modules. Not everyone needs to use all these steps. The steps you follow depend on the sensors and modules you bought and how you plan to use them. Detailed instructions for adding and deleting sensors, lights, and options begin on the next page.
69-1008 Programming Your panel will prompt vou through programming your system. Getting Started To add a sensor: 1. Press Add from the Start menu. 2. Press Sensor from the Main menu until you hear the room or item you want to add. 3. Press the Program button an the sensor. The panel repeats your programming. NOTE: To change a sensor, delete it and reprogram. To set the disarm access code: 1. Press Add from the Start menu. 2. Press Access Code from the Main menu. 3.
-1009 Time-Activated Lights Try Itt . Press Light Control from the Main menu. Press Unit# until you hear the number you chose on the module. Press Sensors from the Control menu until vou hear the sensor you want to control the light. 5. Press DONE. The system voice repeats your programming information. wn Mohave a light or appliance tum on and off at specific times: Press Add from the Start menu. Press Light Control from the Main mer. re Unit # until you hear the number you chose on the module.
Option 1: Disable Panel Siren Option 2: Disable Voice Options 3 & 4: Phone Numbers Option 5: AC Power Failure Option 6: Set Latchkey Time 68-1009 Programming Options To turn the high-level siren off: 1. Press Add from the Start menu. 2. Press Option# from the Main menu. 3. Press DONE. To turn the system voice off during normal operation. 1. Press Add from the Start menu. 2. Press Option# from the Main menu twice. 3. Press DONE.