User's Manual

Bridge
User Guide
Model BR100
23957509
©2013 Ingersoll Rand
Printed in U.S.A.
23957509 Rev. 01/13-d
Bridge MAC ID
twelve (12) characters
1
Locate bridge MAC ID.
Write MAC ID in box at top of this page. You will need it to register
your account.
MAC ID:
XXXXXXXXXXXX
2
Gather information.
To create your account, you will need your credit card and billing
address.
Battery Compartment
MAC ID
-
+
Server Light
Z-Wave™ Light
Minus (-) Button
Plus (+) Button
A/C Input
Ethernet Port and Lights
USE
Enroll Z-Wave Devices
a. Install a fresh, high-quality battery into bridge.
b. Hold bridge within 6 ft. (1.8 m) of device you want to enroll
throughout entire enrollment process.
c. Press and release plus (+) button on bridge.
d. Within 30 seconds, press proper button(s) for enrollment on device.
See the instructions that came with device for more information.
e. Observe lights on bridge. The orange light will blink slowly then
quickly while enrollment is taking place. Enrollment is complete
when orange light becomes solid.
f. Remove battery from bridge.
Exclude Devices
a. Install a fresh, high-quality battery into bridge.
b. Hold bridge within 6 ft. (1.8 m) of device being excluded throughout
entire exclusion process.
c. Press minus (-) button on bridge.
d. Within 30 seconds, press proper button(s) for exclusion on device.
See device instructions for more information.
e. Observe lights on bridge. Orange light will blink slowly then quickly
while exclusion is taking place. Exclusion is complete when orange
light becomes solid.
f. Remove battery from bridge.
Bridge Reset
All enrolled devices and account information will be removed! Call us
if you are unsure whether to proceed.
a. Plug bridge into A/C power.
b. Press and hold plus (+) and minus (-) buttons simultaneously for 10
seconds.
c. Release both buttons.
d. Orange light on bridge will continue to fl ash for 10 - 15 seconds.
This procedure can be used to initialize bridge at any time. See “System
Reset” at www.nexiahome.com for more information.
LIGHTS
Light Condition
Orange
(Z-Wave)
slow blink Waiting for enrollment or exclusion to begin
fast blink Enrollment or exclusion is taking place
solid At least one Z-Wave device was enrolled or
excluded
fl icker Z-Wave activity is detected on local network
Green
(Server)
solid Connected to the server
fl icker Information is being exchanged with server
2 blinks Bridge does not have an IP address. Verify
that bridge is connected to router and that
router DHCP is enabled
3 blinks Bridge has contacted server but connection
was denied. Unplug bridge for 10 seconds.
If problem persists, call us.
no light
(but orange
light is solid)
Ethernet cable not connected
Blue Nexia solid Bridge is powered by A/C
slow blink Bridge is powered by battery
Blue, Green
and Orange
solid Low battery, when bridge not connected to
A/C and battery is installed
no light No A/C or battery
Green and
Orange
blink for 5
seconds
Occurs during reset. After reset, orange
light will continue to blink for 5 seconds.
Ethernet
Lights
solid or
blinking
Internet connected
3
Set up online account.
a. Browse to
www.mynexia.com.
b. Find “Just purchased a Nexia Home Intelligence System? Click
here” and click the link.
c. Follow on-screen instructions to create your account.
d. Your bridge will be automatically updated.
Battery
The 9V battery is used only to enroll and exclude devices. It does
not provide data backup. Bridge will retain data even when power is
completely removed.
SETUP
www.nexiahome.com
[phone]
FCC Interference Statement
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
• Consult the dealer or an experienced radio/television
technician for help.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
Note: Any modifi cations made to this device that are not
approved by Ingersoll Rand Security Technologies may void
the authority granted to the user by the FCC to operate this
equipment.
Industry Canada Statement
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Declaración de Interferencia de la CCF
Este equipo ha sido probado y se ha encontrado que
cumple con los límites para los dispositivos digitales Clase
B, de conformidad con la Parte 15 de las Reglas de la
CCF. Estos límites están diseñados para proporcionar una
protección razonable contra interferencia dañina en una
instalación residencial. Este equipo genera, usa y puede
radiar energía de radio frecuencia y, si no se instala y
utiliza de conformidad con las instrucciones, puede causar
interferencia dañina a las comunicaciones por radio. Sin
embargo, no existe garantía de que no ocurrirá interferencia
en una instalación específi ca. Si este equipo causa
interferencia dañina a la recepción de radio o televisión,
que se puede determinar al encender y apagar el equipo, el
usuario deberá intentar corregir la interferencia con una de
las siguientes medidas:
• Reorientar o relocalizar la antena receptora
• Incrementar la separación entre el equipo y el receptor
• Conectar el equipo en un toma corriente en un circuito
diferente al cual está conectado el receptor
• Consultar al distribuidor o un técnico experimentado de
radio/TV para ayuda.
Este dispositivo cumple con la Parte 15 de las Reglas
de la CCF. La operación está sujeta a las siguientes
dos condiciones: (1) Este dispositivo no puede causar
interferencia dañina y (2) este dispositivo debe aceptar
cualquier interferencia recibida, incluyendo interferencia que
pueda causar una operación no deseada.
Nota: Cualquier modifi cación a este dispositivo que
no se encuentre aprobada por Ingersoll Rand Security
Technologies puede anular la autoridad otorgada al usuario
por la FCC para operar este equipo.
Déclaration de la CFC relative au brouillage
Cet équipement a été examiné et jugé conforme aux limites
fi xées pour un dispositif numérique de classe B, en vertu de
la Section 15 des Règles de la CFC. Ces limites sont établies
en vue de fournir une protection raisonnable contre tout
brouillage dans une installation résidentielle. Cet équipement
entraîne des usages et peut produire des radiofréquences;
s’il n’est pas installé et utilisé selon les instructions, il peut
causer du brouillage nuisible aux radiocommunications.
Toutefois, il n’y a aucune garantie que le brouillage ne se
produira pas dans une installation quelconque. Si cet
équipement cause du brouillage au niveau de la réception
d’un appareil radio ou d’une télévision, ce qu’on peut établir
lorsqu’on met l’équipement en marche et qu’on le met en
arrêt, on recommande à l’utilisateur de tenter de corriger ce
brouillage de l’une des façons suivantes :
• Réorientez ou relocalisez l’antenne réceptrice
• Augmentez la distance qui sépare l’équipement et le
récepteur
• Branchez l’équipement dans une prise de courant ou à un
circuit différent de celui où se trouve branché le récepteur
• Consultez le détaillant ou demandez de l’aide d’un
technicien d’expérience en matière de radio et de télévision.
Ce dispositif est conforme à la partie 15 des règlements
de la FCC. Le fonctionnement est assujetti aux deux
conditions suivantes : (1) Le dispositif ne doit pas émettre
d’interférences nuisibles, et (2) ce dispositif doit accepter
toute les interférences reçues incluant celles pouvant nuire
au fonctionnement.
Remarque : Toute modifi cation apportée à ce dispositif et
n’ayant pas été approuvée par Ingersoll Rand Security
Technologies peut annuler le droit d’utilisation de cet appareil
qui a été accordé à l’utilisateur par la FCC.
Déclaration de la Industrie Canada
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Ingersoll Rand Security Technologies
Model # BR100
FCC ID: XPB-ZWBRIDGEG2
IC: 8053B-ZWBRIDGEG2