User's Manual

ManualsBrandsSchlage Lock ManualsElectronicsNDA Series Wireless Lock

*P516-958*

P516-958

Installation Preparation

Tools Needed

• Phillips screwdriver

• Pin wrench

• Pencil

Optional

• T-15 Tamper Torx screwdriver

Door preparation:

For door preparation

instructions, see included

instructions or contact

Technical Service at

1-877-671-7011.

IMPORTANT NOTES

Magnet tray and included strike MUST be installed!

The magnet is used to indicate door position.

Door position MUST be calibrated using the application.

Install and test lock with door open to avoid being locked out.

MOBILE APPLICATION

Search for “Schlage Engage” in the

Apple App Store or Google Play Store to

download.

Navigate to the website to set up your

online account.

A Install latch.

The bevel must face toward the door stop.

Actual Size

NDE Wireless Lock

Model NDE80 Installation Instructions and User Guide

Cylinder Options

Full Size IC (FSIC)

Small Format (SFIC)

Standard Cylinder

Pin wrench

Latch

Cylinder

Backplate

Spring Cage

Inside Lever

Battery Cover

Screw

Battery Strap

Escutcheon

Screws

Inside

Assembly

Outside Lever

Outside Assembly

Key

Ribbon Cable

Strike

Battery Holder

Chassis

Mounting

Screws

ANSI Strike T-Strike

Strike Options

Summary of content (9 pages)

PAGE 1
*P516-958* NDE Wireless Lock P516-958 Model NDE80 Installation Instructions and User Guide Outside Assembly Cylinder Options Pin wrench Ribbon Cable Full Size IC (FSIC) Key Small Format (SFIC) Spring Cage Outside Lever Cylinder Inside Assembly Strike Escutcheon Screws Chassis Latch Standard Cylinder Battery Cover Backplate Strike Options Inside Lever Mounting Screws Battery Strap Battery Holder ANSI Strike T-Strike Installation Preparation Tools Needed • Phillips screwdriver • Pin wren
PAGE 2
B Door Thickness Adjustment Install strike and magnet tray assembly. For 1B\,” or 2” thick doors, complete the following door thickness adjustment steps. Note: If dustbox is included, install first. CAUTION Magnet tray and included strike must be installed! DO NOT DISCARD! LL For 1C\v” thick doors, NO ADJUSTMENT IS REQUIRED. Continue to step 3. A Remove chassis from outside assembly.
PAGE 3
D Reinstall adjustment plate. Tighten until door thickness insert enters notch in adjustment plate. 1b To change handing, pull lever post until it stops, then rotate 180 degrees. Align lever catch pin and slide hole to latch side. Release lever post. Assembly will click into place. CAUTION Do not route ribbon cable before rotating chassis! Lever Catch Pin E Do not route ribbon cable! Secure chassis in outside assembly. Continue to next step.
PAGE 4
2 Align assembly and install on door. Let the wire hang on the other side, through the hole. 4 Install spring cage. Align lever catch pin to door edge. WARNING Do not pinch ribbon cable! WARNING Ensure that the lever catch pin is aligned with latch side before continuing! Lever Catch Pin Actual Size 5 Install inside escutcheon. 5a Connect the cable from the outside escutcheon to the port on the inside escutcheon. 5b Place inside escutcheon on backplate, and slide down to hook onto backplate.
PAGE 5
Install Batteries 6 Install batteries into battery holder. 6a Push the tab on the right of the battery securing band, and pull out to release battery holder. 6b Connect cable from battery holder to connector on circuit board. 7 Install battery cover screw. Choose either standard Phillips screw or Torx screw. OR 8 Screw into center of hole. Install battery cover. Install battery cover in place, then push up to secure the cover. Tighten bottom cover screw.
PAGE 6
Lever Removal Lever With Interchangeable Core Cylinder Install cylinder tailpiece. To remove a lever with a cylinder, insert key first, and turn it 90 degrees toward door edge. Press pin wrench into hole in lever, and pull off. To remove a lever without a cylinder, press pin wrench into hole in lever, and pull off. Rotate cam in lever post until the cam stops. Insert key into cylinder and insert into lever. Rotate the key clockwise 15 degrees.
PAGE 7
User Guide NEED HELP? See Troubleshooting on pages 8 - 9. Construction Access Mode Lock Testing Construction Access Mode is NOT required to operate lock. Construction Access Mode is used to allow access before the lock is linked and/or for testing purposes before linking. Construction Access Mode requires a credential other than a PIN. • Enabled by default and after a factory reset. Correct lock installation is indicated by three green LED flashes and beeps at the end of power on boot up.
PAGE 8
Reset to Factory Default A Factory Default Reset (FDR) will return the NDE lock settings to the original settings as shipped from the factory. Removes configurations, databases, and requires the lock to be re-captured. A FDR will not remove the lock from your ENGAGE account. A Press and hold the FDR button for five seconds. The NDE will blink green two times and beep two times. B Turn the inside lever three times. LED will blink red and beep with each turn.
PAGE 9
Problem Intermittent Wi-Fi connection Wi-Fi signal is weak After enrolling credentials and access files into the NDE, all valid cards are still denied. Possible Cause • Your phone’s Wi-Fi may be turned off. • You may be too far from a Wi-Fi access point or have walls blocking the Wi-Fi signal. • DPS (door position sensor) is not calibrated. • Activation or Expiration date errors.