Backup Key Parts Backplate Battery Cover Touchscreen Assembly Inside Assembly Bolt Strike and Reinforcement OR Plate Reinforcement Screws Backplate Screws Inside Assembly Screws Bolt/Strike Screws Reinforcement Strike
Start here! Visit alle.co/encodeplus for an improved installation experience. Access online interactive instructions, warranty, and reference information. alle.
Touchscreen Communication Icon • Flashes when lock is connecting to WiFi to check for updates. Low Battery Icon • Flashes after code is entered when battery is low. • Solid when battery is critical. The lock will not work without new batteries. Programming and Input LED • Amber when using manual programming mode. Home Button and Checkmark Icon • Turns on keypad backlight. • Checkmark flashes when code entry is correct. • Checkmark flashes when manual programming is successful.
1 2 3 4 5 Tools Phillips screwdriver Don’t use a power drill! step 1 Remove existing lock. Remove the entire deadbolt, including the bolt. You may also want to remove the strike. A standard Schlage deadbolt is shown. Check with your specific deadbolt manufacturer if you need help.
step 2 Need Help? Visit alle.co/encodeplus Install the bolt. You may have to adjust your bolt length. Make sure the slot in the bolt is centered in the hole. Slot is centered in the hole. No change needed. Make sure the word “TOP” is facing up. Twist the faceplate to extend. Actual Size Keep twisting until 2 ¾”.
Need Help? step 3 Trouble installing the strike reinforcer? Visit alle.co/encodeplus Install the strike into the door frame. If you have a window next to your door, you may not be able to use the longer wood screws to install the strike. Do not reuse existing strike for proper operation. Actual Size Actual Size Install this strike reinforcer for enhanced security. OR Reinforcement strike.
step 4 Is it hard to install the touchscreen? Is the tailpiece not installing correctly? If your through hole seems too small, you may need to remove the spacer. Visit alle.co/encodeplus. Install the touchscreen. Route the cable through the door BELOW the bolt. Align the tailpiece as shown and push the touchscreen onto the door. The bump on the tailpiece aligns with the slot in the bolt.
4 3 2 1 5 5 step Phillips screwdriver Don’t use a power drill! You may damage your lock! Install the backplate. Route the cable under the bolt and through the hole on the bottom of the backplate. Secure the backplate with screws. Make sure the outside touchscreen is straight before tightening screws all the way.
step 6 Connect the cable. Tuck the cable and connector in the space above the spindle.
5 4 3 2 7 1 step Phillips screwdriver Don’t use a power drill! You may damage your lock! Secure the lock to the door. If the bump on the tailpiece doesn’t align with the slot in the back of the inside assembly, make sure your thumbturn is vertical (up and down). The bump on the tailpiece aligns with the slot in the back of the inside assembly.
step 8 Install batteries and slide the cover on. Pull out battery holder. Install batteries. Reinstall battery holder. Turn the battery holder around so the batteries face the door.
That wasn’t so bad, was it? Your lock is now installed! Remember, you still have to set up your lock to use it. step 9 Set up your lock. 1. Open your door! 2. Enter one of the two default user codes. 3. Your lock will enter a setup routine. When the bolt stops moving, setup is complete. Final test! 1. Close your door. 2. Extend and retract the bolt using the inside thumbturn. 3. Make sure the bolt retracts smoothly. 4. Open your door. 5. Extend the bolt using the inside thumbturn. 6.
Now that your lock is installed you can use the Schlage Home app to lock and unlock your door from anywhere and add codes for guests and household members.
Or set it up using the Apple Home app For iPhone XS and newer, simply press the button on the lock, then tap your phone to the label. For older models, turn the page.
Older than iPhone XS 1 Press the button on your lock Remove battery cover and press the button. Your lock will be in pairing mode for 5 minutes. 2 Open the Apple Home app Press “+” and Add Accessory. Follow directions on your phone. Note: Your lock must be fully installed on door with batteries before pairing with an app.
For iPhone 7 - iPhone X Tap your iPhone to the HomeKit label Tap the top of your phone to the label. Follow directions on your phone. OR For older than iPhone 7 or iPad PLACE LABEL HERE These are your backup codes. You will need these codes if you ever factory default reset your lock. Keep these safe! Questions about your new BE499 Deadbolt? Please don’t return it to the store! alle.co/encode © Allegion 2021 Printed in U.S.A. 47360452 Rev.
Lock and unlock To lock your door just tap the lock icon. You can also lock your door from inside by turning the thumbturn toward the door edge. To unlock your door enter a user code. Once paired with a smart home system, the default codes will not work. You can also unlock your door from inside by turning the thumbturn away from the door edge.
Apple HomeKit Apple HomeKit technology provides an easy, secure way to control your home’s doors and more using the Apple Home app and Siri on your iPhone, iPad, Apple Watch, HomePod, or Mac.
PLACE LABEL HERE These are your backup codes. You will need these codes if you ever factory default reset your lock. Keep these safe! Questions about your new Please don’t return it to the store! Let us help you first! alle.co/encodeplus © Allegion 2021 Printed in U.S.A. 47360452 Rev.