User Manual

ManualsBrandsSchlage Lock ManualsElectronicsAllegion AD 900 MHz Module V2

User’s Manual -COMAD400V2 900 MHz Communications Board

The communications module is a 900 MHz transceiver for electronic locks and non-lock devices. The

communications module links the access device to the Access Control Management System, with feedback

control to the Access Device via a wireless means. The module contains the embedded firmware

implementing the radio physical and data layers. There are 5 antennas associated with this module:

1. PCB trace antenna with a 5.7dBi maximum gain (measured over a conducting ground plane).

2. MA-CC60-60 Dual Beam Antenna with a 3.5dBi gain (Data sheet)

3. MA-CL67-15 multi band Directional Panel antenna with 8.5dBi gain (Data sheet)

4. MA-CL92-5 Quasi-Omni Panel antenna with 4.5dBi gain (Data sheet)

5. MA-CM36-15 multi band Omni Antenna with 2dBi gain (Data sheet.

Specifications of the radio module:

Power Output: 19.6 dBm

Operating Frequency: 906 - 924 MHz

Modulation: BPSK

NOTE: The intended use of this module is not for the general public. It is generally for industry/commercial use

only. This transceiver is to be professionally installed in the end product by Schlage Lock Company, and not by

a third party. The Schlage Lock Company COMAD400V2 900 MHz Communications Board Module will not be

sold to third parties via retail, general public or mail order. In the case of a repair, the transceiver will be

replaced by a professional Installer.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

FCC/IC Caution: Any changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate this equipment.

To comply with FCC/IC RF exposure limits for general population/uncontrolled exposure, the antenna(s) used

for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must

not be co-located or operating in conjunction with any other antenna or transmitter.

Summary of content (4 pages)

PAGE 1
User’s Manual -COMAD400V2 900 MHz Communications Board The communications module is a 900 MHz transceiver for electronic locks and non-lock devices. The communications module links the access device to the Access Control Management System, with feedback control to the Access Device via a wireless means. The module contains the embedded firmware implementing the radio physical and data layers. There are 5 antennas associated with this module: 1. PCB trace antenna with a 5.
PAGE 2
INDUSTRY CANADA STATEMENTS This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
PAGE 3
DÉCLARATIONS DE INDUSTRIE Canada Cet appareil est conforme norme Industrie Canada RSS exempts de licence (s). Son fonctionnement est soumis aux deux conditions suivantes: 1) cet appareil ne doit pas provoquer d’interférences, et 2) cet appareil doit accepter toute interférence, y compris les interférences pouvant provoquer un fonctionnement indésirable de l’appareil.
PAGE 4
Schlage Lock Company Responsibilities to comply with FCC and Industry Canada Regulations The COMAD400V2 900 MHz Communications Board Module has been certified for integration into products only by Schlage Lock Company under the following conditions: 1. The antenna(s) must be installed such that a minimum separation distance of 20cm is maintained between the radiator (antenna) and all persons at all times. 2.