User’s Guide TouchScreen Deadbolt with Alarm
CONTENTS Security You Hear Instantly ...................... 2 Customer Service and Help .................. 3 Troubleshooting ..................................... 10 Factory Default Reset ........................ 11 Lock Parts ................................................ 4 My Codes ............................................... 12 Best Practices .................................... 12 Default Programming and User Codes Locations ........................................... 12 Locking and Unlocking..
LOCK SETUP Follow these steps to get your lock set up and ready to use. 1. More information coming soon.
LOCK PARTS DOOR EXTERIOR Keypad Assembly Outside Schlage Button Touchscreen Cylinder Bolt DOOR INTERIOR Alarm Assembly ENGLISH Alarm Inside Schlage Button Thumbturn Inside Schlage Button Thumbturn Outside Schlage Button Touchscreen Cylinder Alarm Bolt • Located on the inside of the door. • Has three distinct lights and used to set and program the alarm. Programming the Alarm on page 8. • This button does not lock or unlock the door. • Used to lock and unlock the door from the inside.
LOCKING AND UNLOCKING If you make a mistake while entering a User Code, press the Outside Schlage Button and start again. Locking from the Outside Locking from the Inside Press the Outside Schlage Button. The lock will lock.1 Rotate the Inside Thumbturn. 1 If the Lock & Leave feature is disabled, a valid User Code must be entered to lock the door. See Enable/Disable Lock & Leave on page 7. Unlocking from the Inside Press the Outside Schlage Button and then enter a valid User Code into the Keypad.
PROGRAMMING THE TOUCHSCREEN Finding your Default Codes Default Codes are located on the back of the Alarm Assembly, and on the back of this guide. Want to see a video of programming before you begin? Browse to www.schlage.com. The lock comes preset with a unique default Programming Code and two unique default User Codes. You can either use these codes to operate your lock or change them using the instructions in this guide.
Programming Descriptions Add User Code User Codes are used for unlocking the lock. Codes can be 4 - 8 digits long. All codes must be the same length. See Change User Code Length. Removes one User Code Change Programming Code The Programming Code is used to put the lock into Programming Mode. It is 6 digits long. Enable Vacation Mode When Vacation Mode is enabled, no User Codes can be entered into the TouchScreen.
PROGRAMMING THE ALARM Powering the Alarm The alarm is turned off by default. After installation, you’ll need to turn on your alarm. Program the alarm using the Inside Schlage Button, shown below. Not sure your alarm is turned on? Simply press the Inside Alarm Button once. It will beep and light up to confirm it is activated. If it does not, try turning the alarm on again, and check the batteries. For videos and more, browse to alarm.schlage.com.
Changing the Alarm Setting After you power on the alarm, it will be preset to the Forced Entry alert, by default. If you want to change it from Forced Entry to another alert setting, follow these simple steps: The alarm must first be powered on before changing the alert setting! Release after first flash (about 2 seconds) Tamper Alert Click the button until the MIDDLE light is lit. Activity Alert Click the button until the LEFT light is lit.
TROUBLESHOOTING ENGLISH PROBLEM 10 SOUNDS LIGHTS Alarm sounds too frequently or false alarm Alarm — The tamper alert is not sounding. — — I forgot my Programming — Code. — I need to delete a User Code that I don’t remember. — — User Code does not unlock lock. User Code cannot be entered after Outside Schlage button is pressed User Code cannot be entered after Outside Schlage button is pressed.
PROBLEM LIGHTS 2 beep Yellow dot flashing 2 Red X 2 beep 2 Red X 2 beep 2 Red X — 2 beep Yellow dot flashing 2 Red X 2 beep 2 Red X 2 beep Yellow dot flashing 2 Red X 2 beep 2 Red X 2 beep 2 Red X Cannot delete all User Codes — Deadbolt will not extend or retract as expected. Several beeps Yellow dot flashing Red X flashing NEXIA services are not available. — — Cannot delete a User Code Cannot change Programming Code. SOLUTION “1” was not pressed after entering programming mode.
MY CODES Use these tables to record Programming and User Codes that you program into the lock. The Programming Code can be any combination of six numbers entered into the keypad to put the lock in programming mode. The first 4 - 6 numbers (depending on User Code length) must be different from all of the User Codes currently in the Use a pencil to enter lock. One Programming Code is programmed into the lock by the codes in the boxes default.
DATE PROGRAMMING CODE USER NAME Example: John Smith 1. USER CODE 1234 2. 3. 4. 5. 6. 8. 9. ENGLISH 7. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30.
NEXIA HOME INTELLIGENCE FUNCTIONS This lock is equipped with a Z-Wave radio, which allows it to integrate seamlessly with the Nexia Home Intelligence System. Enrolling is the process of adding the lock to your Nexia Home Intelligence account. To enroll the lock, you must first have a Nexia Home Bridge and Nexia Home Intelligence account. For more information about Nexia Home Intelligence, please browse to www.nexiahome.com. The Z-Wave radio is disabled by default to conserve battery life.
WARRANTY AND FCC/IC STATEMENTS Lifetime Limited Mechanical and Finish Warranty and 1-Year Limited Electronics Warranty Subject to the terms and conditions of the warranty, Schlage extends a lifetime limited mechanical and finish warranty and a one-year limited electronics warranty to the original consumer user (“Original User”) of our Schlage brand product (“Product”) against defects in material and workmanship, as long as the Original User occupies the residential premises upon which the Product was origin
If you have questions about any part of installation or programming, don’t return the Keypad Deadbolt with Built-in Alarm to the store. Our Schlage Customer Service representatives are ready to help. Toll-Free: 1.888.805.9837 Live Chat: schlage.com To learn more about this product, scan the code with your smartphone. Download the app at scanlife.com.