User Manual

ManualsBrandsSchlage Electronic Security ManualsElectronicsDoor Lock

Form 51005 Rev. D

12-02-2002

CM5100 COMPUTER MANAGED CYLINDRICAL LOCK

INSTALLATION MANUAL

CM5100-KPI CM5100-IBO

CM5100-MGK CM5100-MGI

PRO5100

The 5100 series lock is a stand-alone, microprocessor controlled, electromechani-

cal locking system. The 5100 employs a heavy-duty mechanical design with fewer

moving parts than a standard cylindrical lockset, for ease of installation and high

reliability. It is powered by four, standard AA batteries, providing up to 80,000 acti-

vations.

Operationally, the outside lever is normally locked and the inside lever is always

free to allow egress. Electronic access control is achieved by entering an ”Access

Credential” (magnetic stripe card, code, iButton Key, or Prox fob or card).

Electronic access control capabilities are listed below by model. All models are

designed to accommodate an emergency mechanical key override. Standard fea-

tures of the CM models include up to 1000 user memory, real time features includ-

ing time zones and holidays, and audit trail of up to 1000 events. Optional ATK

(audit trail - key override) will note any use of the mechanical key on the audit trail

report. Manual and computer programming is supported by all models. The PRO

models are manually programmed to accept up to 100 codes.

Functions

5190: Office Function - has “Lock” and “Unlock” buttons on inside escutcheon -

function not available on PRO

5196: Storeroom/Classroom Function - can be unlocked by “toggle” credential and

relocked again by same. See programming guide for more information.

5198: Classroom Function with inside iButton reader - can be toggled unlocked by

iButton plus pin (code). Can be relocked immediately from inside iButton reader in

an emergency.

Models

KPI: iButton reader and keypad

IBO: iButton reader only

MGK: Magnetic stripe card reader, iButton reader and keypad

MGI: Magnetic stripe card reader and iButton reader

PXK: HID Prox card reader, iButton reader, and keypad

PXI: HID Prox card reader and iButton reader

PPK: interflex ProxIF Prox card reader, iButton reader, and keypad

PPI: interflex ProxIF Prox card reader and iButton reader

PCK: Casi Rusco Prox card reader, iButton reader, and keypad

PCI: Casi Rusco Prox card reader and iButton reader

PRO: Keypad only - no computer programming, 100 code memory

Options:

ATK: Audit trail of mechanical key use (not available on PRO)

HSS: High security screws on inside escutcheon

SLB: 2-3/4” backset, 1/2” latch bolt

OLB: 2-3/8” backset, 1/2” latch bolt

ELB: 2-3/4” backset, 3/4” latch bolt

T3: Track 3 card reader (data on track 3

must be ABA track 2 format) - MGI/MGK only

KD: Keyed Different, includes Schlage

Everest cylinder

LC: Less Cylinder

5100 CYLINDRICAL

LOCKSET - STANDARD

CM5198

SAFE SCHOOL LOCK

WITH iBUTTON

READER ON INSIDE

CM5100-PXK

CM5100-PPK

CM5100-PCK

CM5100-PXI

CM5100-PPI

CM5100-PCI

Summary of content (8 pages)

PAGE 1
CM5100 COMPUTER MANAGED CYLINDRICAL LOCK INSTALLATION MANUAL The 5100 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5100 employs a heavy-duty mechanical design with fewer moving parts than a standard cylindrical lockset, for ease of installation and high reliability. It is powered by four, standard AA batteries, providing up to 80,000 activations. Operationally, the outside lever is normally locked and the inside lever is always free to allow egress.
PAGE 2
CM5100 COMPUTER MANAGED CYLINDRICAL LOCK INSTALLATION MANUAL BEFORE YOU BEGIN: Standard units are shipped from the factory to fit 1-3/4” doors. Verify that the door thickness. If the door is not 1-3/4” thick, verify that the door thickness option was ordered or consult factory. 1. PREP DOOR AND FRAME: A. Determine door hand and correct backset. B. Mark the horizontal and vertical centerlines for the lockset, latch and strike. C.
PAGE 3
CM5100 COMPUTER MANAGED CYLINDRICAL LOCK INSTALLATION MANUAL 2. INSTALL CYLINDER (IF NOT ALREADY DONE), GASKET AND STANDOFFS: A. Install cam onto cylinder (if not already done.) Cam must be a straight, 11/16” design. See below for recommended cams. B. Insert mortise cylinder into outside escutcheon from front (keypad/reader) side with keyway down. C. Slide lock washer onto cylinder (tab on top facing out, as shown below.) D. Using nut tool (provided) tighten nut onto cylinder. E.
PAGE 4
CM5100 COMPUTER MANAGED CYLINDRICAL LOCK INSTALLATION MANUAL 3. CHANGE HAND (IF NECESSARY): NOTE: The locks are shipped handed as ordered from factory. If it is necessary to change the hand of the lock, follow the steps below: A. Remove retractor by loosening two 9/64” socket cap screws which attach it to the outside escutcheon. B. Remove outside spindle. C. Loosen 5/32” socket cap screw which secures handle to escutcheon. D. Remove, rotate and re-install handle (NOTE: some handle designs have an adapter.
PAGE 5
CM5100 COMPUTER MANAGED CYLINDRICAL LOCK INSTALLATION MANUAL 4. INSTALL STRIKE BOX AND STRIKE: 5. INSTALL LATCH AND OUTSIDE ESCUTCHEON: A. Install latch into edge of door. Be sure to install it with the beveled edge facing door jamb. B. If the door is less than 1-3/4 thick, slide spacer over standoffs and retractor on outside escutcheon. C. Carefully install the outside escutcheon onto the door, passing the wiring harness through the 1” hole.
PAGE 6
CM5100 COMPUTER MANAGED CYLINDRICAL LOCK INSTALLATION MANUAL 6. INSTALL BASE PLATE ASSEMBLY: Install base plate assembly onto inside of door. (If the door is less than 1-3/4” thick, install spacer between the base plate and the door.) Use socket cap screws with washers on upper standoffs and phillips head screws on lower (retractor assembly) standoffs. SPACER (FOR DOORS LESS THAN 1-3/4”) CAUTION! If any fasteners such, as washers, fall behind the PC board, remove them prior to installing batteries.
PAGE 7
CM5100 COMPUTER MANAGED CYLINDRICAL LOCK INSTALLATION MANUAL 7. INSTALL INSIDE SPINDLE, BATTERIES, AND INSIDE ESCUTCHEON: NOTE: The lock is shipped with four AA alkaline batteries. Always use new, high quality alkaline batteries. A. Plug wiring harness into PC board. B. Tuck wiring harness under retaining clip as shown in detail. C. Install four AA batteries as shown, note polarity indication on battery holders. D. Insert inside spindle with flat side showing. E.
PAGE 8
CM5100 COMPUTER MANAGED CYLINDRICAL LOCK INSTALLATION MANUAL OPERATIONAL TEST: TROUBLE SHOOTING: PROBLEM: POSSIBLE CAUSE: 1. Push down and up on inside lever: latch should retract. 2. Push down and up on outside lever. Lever should be disengaged from retractor and door should not unlock. 3. Insert mechanical key into cylinder and turn counterclockwise until it stops. Push down and up on the outside lever. The door should unlock.