User Manual

ManualsBrandsSchlage Electronic Security ManualsElectronicsDoor Lock Low Power Proximity Transmitter

Form 55005 Rev. B

09-25-2001

CM5500 COMPUTER MANAGED MORTISE LOCK

INSTALLATION MANUAL

CM5500-KPI CM5500-IBO

CM5500-MGK CM5500-MGI

CM5500-PXK CM5500-PXI

PRO5500

The 5500 series lock is a stand-alone, microprocessor controlled, electromechani-

cal locking system. The 5500 employs a heavy-duty mechanical design with fewer

moving parts that a standard mechanical mortise lockset, for ease of installation

and high reliability. It is powered by four, standard AA batteries, providing up to

80,000 activations.

Operationally, the outside lever is normally locked and the inside lever always

retracts the bolt to allow egress. Electronic access control is achieved by entering

an”Access Credential” (magnetic stripe card, code of iButton Key, or HID Prox fob

or card). Electronic access control capabilities are listed below by model. All mod-

els are designed to accommodate an emergency mechanical key override.

Standard features of the CM models include up to 1000 user memory, real time

features including time zones and holidays, and audit trail of up to 1000 events.

Optional ATK (audit trail - key override) will note any use of the mechanical key on

the audit trail report. Manual and computer programming is supported by all mod-

els. The PRO models are manually programmed to accept up to 100 codes.

Functions:

5590: Office Function (3/4” latch) - has “Lock” and “Unlock” buttons on inside

escutcheon. Function not available on PRO

5596: Storeroom/Classroom Function (3/4” latch) - can be unlocked by “toggle”

credential and relocked again by same. See programming guide for more informa-

tion (form 57000).

5598: Classroom Function with inside iButton reader - can be toggled unlocked by

iButton plus pin (code). Can be relocked immediately from inside iButton reader in

an emergency.

5591: Office Function (1” Autobolt) - has “Lock” and “Unlock” buttons on inside

escutcheon. Function not available on PRO

5594: Storeroom/Classroom Function (1” Autobolt) - can be unlocked by “toggle”

credential and relocked again by same. See programming guide for more informa-

tion (form 57000). Function not available on PRO

5593: Dormitory/Privacy Function (1” Autobolt) - Pushing either button on the

inside escutcheon places lock in the “Privacy” mode: a “Lockout” credential or

mechanical key is required to enter. Condition is cleared when the bolt is retracted

from the inside. Function not available on PRO

Models:

KPI: iButton reader and keypad

IBO: iButton reader only

MGK: Magnetic stripe card reader, iButton reader and keypad

MGI: Magnetic stripe card reader and iButton reader

PXK: Prox card reader, iButton reader, and keypad

PXI: Prox card reader and iButton reader

PRO: Keypad only - Manual programming only, 100 code memory

Options:

ATK: Audit trail of mechanical

key use (not available on PRO)

HSS: High security screws on

inside escutcheon

T3: Track 3 card reader

(data must be ABA track 2 for-

mat) - MGI/MGK only

KD: Keyed Different, includes

Schlage Everest cylinder

LC: Less Cylinder

5500 MORTISE LOCK

AUTOBOLT

5500 MORTISE LOCK

STANDARD

CM5598

SAFE SCHOOL LOCK

WITH iBUTTON

READER ON INSIDE

Summary of content (8 pages)

PAGE 1
CM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL The 5500 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5500 employs a heavy-duty mechanical design with fewer moving parts that a standard mechanical mortise lockset, for ease of installation and high reliability. It is powered by four, standard AA batteries, providing up to 80,000 activations.
PAGE 2
CM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL BEFORE YOU BEGIN: Standard units are shipped from the factory to fit 1-3/4” doors. Verify the door thickness. If the door is not 1-3/4” thick, verify that the door thickness option was ordered or consult factory. 1. PREP DOOR AND FRAME (IF NOT ALREADY DONE): A. Determine door hand. B. Mark the horizontal and vertical centerlines for the lock case (on door edge), strike, lever, and inside escutcheon. Note that the backset is actually 2.
PAGE 3
CM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL 2. INSTALL CYLINDER, GASKET AND STANDOFFS: A. Install cam onto cylinder. Cam can be either a cloverleaf (shown) or straight, 11/16” design (not shown). B. Insert standard, 1-1/4” mortise cylinder into outside escutcheon from front (keypad/reader) side with keyway down. C. Slide lock washer into place with tab on top facing out, as shown below. D. Using nut tool (provided) tighten nut onto cylinder. E.
PAGE 4
CM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL 3. CHANGE HAND (IF NECESSARY): CHANGE PIN NOTE: The locks are shipped as ordered from factory. If it is necessary to change the hand of the lock, follow the steps below: A TO CHANGE HAND OF LOCK CASE: A. With bolt fully extended, insert change pin (included in the hardware pack) into hole. (It will snap over a groove on the main shaft, holding it in place.) B. Remove set screw in bolt so bolt can be removed. C.
PAGE 5
CM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL 4. INSTALL STRIKE BOX AND STRIKE: IMPORTANT! Strike included with lock MUST be used for proper operation of mortise lockset. 5. INSTALL LOCK CASE: Install lock case into edge of door. If the lock has the Privacy option, feed the wire harness though the 3/4” hole as shown below. Secure to door with #12-24 combination screws. IF UNIT HAS PRIVACY FEATURE, FEED WIRE THROUGH CAVITY AND OUT #12 COMBINATION 3/4” HOLE AS LOCK CASE IS INSERTED.
PAGE 6
CM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL 6. INSTALL OUTSIDE SPINDLE, OUTSIDE ESCUTCHEON AND BASE PLATE ASSEMBLY: Install base plate assembly onto inside of door. Use socket cap screws with washers on top standoffs and phillips head screws on retractor assembly (bottom). Note that the cam on the outside escutcheon must be positioned with the dot at the 6 O’Clock position and inside spindle must be inserted as shown in details.
PAGE 7
CM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL 7. INSTALL INSIDE SPINDLE, BATTERIES, AND INSIDE ESCUTCHEON: NOTE: The lock is shipped with four AA alkaline batteries. Always use new, high quality alkaline batteries. A. Plug wiring harness into PC board. B. Tuck wiring harness under retaining clip as shown in detail A, below. Not all wires shown will be present on all models. C. Install four AA batteries. Note polarity indication on battery holders. D. Assemble spring onto inside spindle as shown.
PAGE 8
CM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL OPERATIONAL TEST: TROUBLE SHOOTING: PROBLEM: POSSIBLE CAUSE: 1. Push down and up on inside lever: latch should retract. 2. Push down and up on outside lever. Lever should be disengaged from retractor and door should not unlock. 3. Insert mechanical key into cylinder and turn counterclockwise until it stops (about 1/2 turn). Push down and up on the outside lever. The latch should retract.