Quick Installation Guide

ManualsBrandsSBO Hearing ManualsElectronicsHearing Instrument amplifier Module

Radio Model - Quick Installation Guide

Radio Model Name:

PA_AU5_MBTE_M

SBO Hearing A/S, Kongebakken 9, 2765 Smorum - DK-Denmark,

VAT-no.: DK39818558, www.sbohearing.com

The PA AU5 MiniBTE M radio model (PA_AU5_MBTE_M) contains two radio transceivers running at 3.84 MHz and

2.4 GHz and both implemented on a single hardware platform.

Additionally, a full featured RFID tag (IC2) capable of receiving signals at 865 MHz – 928 MHz. The RFID tag has no

electrical/galvanic connections related to the rest of the PCB in PA AU5 MiniBTE M and are passive.

The radio model is implemented in an engine module mounted on the main PCB with connection to the antennas,

telecoil, the microphones, the internal speaker and the battery terminals. The radio model can be seen in 3D overview

to the left.

The 3.84 MHz radio is a low power, short range inductive radio transceiver (NFMI – Near Field magnetic

Induction) working at a single channel at 3.84 MHz using MSK modulation with 320 kbit/s data rate and

connected to a small coil antenna.

The 2.4 GHz radio is a Bluetooth Low Energy (BLE core 5.0) transceiver using GFSK/2FSK modulation with 1

Mbit/s, 2 Mbit/s data rate also capable of proprietary reception modes (xBLE) with higher data rates (2 Mbit/s, 4

Mbit/s) using 2FSK/4FSK modulation. The 2.4 GHz radio is connected to a short wire antenna with a proprietary

antenna connector.

Below the main flex PCB of the PA AU5 MiniBTE M radio model with the most important electrical and electro-

mechanical components can be seen:

PA AU5 MBTE M Radio Model – 3D

overview

Summary of content (5 pages)

PAGE 1
Radio Model - Quick Installation Guide Radio Model Name: PA_AU5_MBTE_M PA AU5 MBTE M Radio Model – 3D overview The PA AU5 MiniBTE M radio model (PA_AU5_MBTE_M) contains two radio transceivers running at 3.84 MHz and 2.4 GHz and both implemented on a single hardware platform. Additionally, a full featured RFID tag (IC2) capable of receiving signals at 865 MHz – 928 MHz. The RFID tag has no electrical/galvanic connections related to the rest of the PCB in PA AU5 MiniBTE M and are passive.
PAGE 2
Radio Model - Quick Installation Guide Radio Model Name: PA_AU5_MBTE_M PA AU5 MiniBTE M Radio Model – Main PCB – Top side SBO Hearing A/S, Kongebakken 9, 2765 Smorum - DK-Denmark, VAT-no.: DK39818558, www.sbohearing.
PAGE 3
Radio Model - Quick Installation Guide Radio Model Name: PA_AU5_MBTE_M See previous page PCB radio module drawing for placement of the antenna and IC’s relevant for radio: 1. 2. 3. 4. 5. 6. 7.
PAGE 4
Radio Model - Regulatory Label Information for USA & Canada Radio Model Name: Contains: PA_AU5_MBTE_M FCC ID: 2ACAHAU5MBTEM IC: 11936A-AU5MBTEM NOTICE: This device complies with Part 15, Part 15.223, Part 15.247 of the FCC Rules and with RSS-210 and RSS-247 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
PAGE 5
Radio Model - Regulatory Label Information for Japan Radio Model Name: PA_AU5_MBTE_M Description: Radio module with 2.4 GHz low power transceiver to be integrated into various hearing instruments and associated devices. Regulatory label: Cosmic12 miniBTE M: 202-LSJ082 NB: The regulatory label for Japan is also included in the IFU for Japan.