Technical Bulletin PAGE: 1/4 Reissued: 19-Mar-03 Model: General RTB Date: 4-Feb-03 No.: RGene013b RTB Reissue The items in bold italics have been corrected or updated. Subject: Service remarks at installation Prepared by: T. Itoh From: Technical Service Sec. Service Planning Dept.
Technical Bulletin PAGE: 2/4 Reissued: 19-Mar-03 Model: General RTB Date: 4-Feb-03 No.: RGene013b 2. Firmware Modification Due to the counter modification, SP5-849 has also been changed as follows for products that have this SP mode (listed below). Current New SP mode name: Specification: Counter Clear • When the electrical counter is changed from a Day negative value to 0, the machine recognizes this as the counter clear day and stores this date in the NVRAM.
Technical Bulletin PAGE: 3/4 Reissued: 19-Mar-03 Model: General RTB Date: 4-Feb-03 No.
Technical Bulletin PAGE: 4/4 Reissued: 19-Mar-03 Model: General RTB Date: 4-Feb-03 No.: RGene013b 4. Important Notes for Machine Installation – All Products Please be sure to perform the following at machine installation: 1. If the product is from before the counter modification, i.e. the counter is at a negative value, be sure to set the counter value to 0 first, then make the installation test samples. Digital products Analog products Set the electrical counter to 0 with SP mode.
Technical Bulletin Model: Bellini-C2 Date: 7-Apr-03 Subject: SC672 etc PAGE: 1/4 No.: RB070001 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) The Bellini-C2 firmware has been modified to solve the following: SYMPTOM 1. SC672 (controller start-up error) 2.
Technical Bulletin Model: Bellini-C2 PAGE: 2/4 Date: 7-Apr-03 No.: RB070001 Cut-in Serial Numbers RCL (Japan) Production (B070/B071) MODEL NAME Ricoh Aficio 2090 Savin 4090 Gestetner 9002 Lanier LD 090 Gestetner 9002 Nashatec 9005 Rex Rotary 9008 Lanier LD 090 IS 2090 Ricoh Aficio 2090 Ricoh Aficio 2105 Savin 40105 Gestetner 10512 Lanier LD 0105 Gestetner 10512 Nashatec 10515 Rex Rotary 10518 Lanier LD 0105 IS 2105 Ricoh Aficio 2105 V/Hz 208 - 240V/60Hz DESTINATION USA, Canada.
Technical Bulletin Model: Bellini-C2 Date: 7-Apr-03 PAGE: 3/4 No.: RB070001 ACTION REQUIRED Please perform the firmware upgrade on machines made before March 5th 2003 production. (Refer to the above table for machine cut-in serial numbers.) ! ! ! ! Controller: B0705734B: V.1.04.4 NIC: B0705735B: V.4.03 BIOS: B0705742D: K02EL00O LCDC: B0705371B (NA): V.2.07 B0705372B (EU): V.2.07 Note: Please update the above firmware at the same time. << Firmware Update Procedure >> 1. Turn the main switch OFF. 2.
Technical Bulletin Model: Bellini-C2 Date: 7-Apr-03 PAGE: 4/4 No.: RB070001 5. Press the “Update (#)” key. The firmware update will then begin, and the progress bar (*****___) will be displayed on the operation panel. The machine performs the firmware update in the following order: “Network Support” # “System” # “BIOS” # “Ope Panel” Note: ! While the “Ope panel” firmware is being updated, the panel display will be blank (progress bar not displayed).
Technical Bulletin Model: Bellini-C2 Date: 21-Apr-03 Subject: SD Card Information PAGE: 1/8 No.: RB070002 Prepared by: S.Orita From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) We are releasing the SD Card as a new service tool from Bellini-C2. The detailed information is as follows: 1.
Technical Bulletin Model: Bellini-C2 Date: 21-Apr-03 PAGE: 2/8 No.: RB070002 3. Service Information When issuing an FPR (Field Problem Report), the print data and/or debug log data captured by the SD card should be included with the report depending on the type of problem, as it is very useful for analyzing the problem and developing a solution. Please see Section 4-3 below for a detailed description of the functions for the SD card.
Technical Bulletin Model: Bellini-C2 PAGE: 3/8 Date: 21-Apr-03 No.: RB070002 4-3 Features of the Service SD Card The following are the features for the Service SD card at the time this document was issued. Please refer to the Service Manual for the detailed procedures on how to update the firmware or retrieve the data from the machine. 1 Feature Firmware update • • • 2 Data upload and download The following data can be transferred between the NVRAM and the SD card: • • • 3. Debug log 4.
Technical Bulletin Model: Bellini-C2 PAGE: 4/8 Date: 21-Apr-03 No.: RB070002 Therefore, folder arrangement is not critical for firmware downloads, since this process is automatic. However, creating separate folders under “romdata” for each model will make it easier to delete files later on. An easy to remember method would be to name these folders after the 4-digit product code for each model, e.g. B070, then store the firmware here.
Technical Bulletin Model: Bellini-C2 Date: 21-Apr-03 PAGE: 5/8 No.: RB070002 4-5 FIRMWARE DESTRIBUTION Firmware will continue to be provided through the existing route (global server). The .exe file will consist of the firmware and related folders, as shown below. 4-6 HOW TO DUPLICATE A SERVICE SD CARD The following is an example of the contents of an extracted .exe file. Please copy the necessary files/folders onto the SD card, depending on what information already exists in the card.
Technical Bulletin Model: Bellini-C2 PAGE: 6/8 Date: 21-Apr-03 No.: RB070002 5. Special Tools The following special tools have been registered as service parts to support products in the field that use SD cards. However when using SD cards, adapters or reader/writers procured as supply goods locally, please be sure to use tools produced by the same manufacturers listed below. This is because products from these vendors were used for the official product evaluations.
Technical Bulletin Model: Bellini-C2 Date: 21-Apr-03 PAGE: 7/8 No.: RB070002 7. System Requirements 7-1 SD CARD Please read over the important notes described below regarding the handling of the SD card. If these points are not followed carefully, it may cause the card to be damaged or data to be lost. Important Notes: • Do not directly touch the card contacts or bring them into contact with a metallic substance. • Do not bend, drop or apply any force or shock to the card.
Technical Bulletin Model: Bellini-C2 Date: 21-Apr-03 PAGE: 8/8 No.: RB070002 7-2 PCMCIA CARD ADAPTOR / USB READER WRITER Manufacturer Product Code PC Host Interface OS Dimensions PCMCIA Card Adapter USB Reader Writer Panasonic BN-SDAA BN-SDAA2 BN-SDCA BM-SDCE2 IBM PC-AT compatible computer PCMCIA slot USB port Win98 SE or later 85.6x54x5mm 92x56x15mm NOTE: 1. Swap Box for the flash memory (IC) card cannot be used for uploading firmware to the SD card. 2.
Technical Bulletin Model: Bellini-C2 Date: 24-Apr-03 Subject: Firmware update for “0” counter & SMTP PAGE: 1/5 No.: RB070003 Prepared by: M.Matsuda Authentication From: 2nd Tech Support Sec. Service Support Dept.
Technical Bulletin Model: Bellini-C2 Date: 24-Apr-03 PAGE: 2/5 No.: RB070003 Note: *1. These must be updated together as a set for the 0 counter modification. *2. These must be updated together as a set for the SMTP modification. *3. If installing the P/S Kit, for the 0 counter modification, printer v1.13 and scanner v2.00 are necessary in addition to the mainframe versions listed above. *4. System firmware v2.12.7 must be installed first, before the Webdocbox or Websys.
Technical Bulletin Model: Bellini-C2 Date: 24-Apr-03 PAGE: 3/5 No.: RB070003 2. The SMTP Authentication modification << SP Modes for the SMTP Authentication>> The following SP modes are added for SMTP authentication after updating to the firmware versions listed above (5852-002 is an existing SP mode). Important: ! Make sure to print out the NIB Summary Report before updating the firmware.
Technical Bulletin Model: Bellini-C2 5852 Date: 24-Apr-03 PAGE: 4/5 No.: RB070003 007 POP before SMTP A flag that determines whether the POP server is connected before connecting to the SMTP server. [0~1 / 0 / 1] POP 0: OFF 1: On Post Office Protocol (POP) servers are computers that receive mail using SMTP. The mail includes a setting to ensure that it is directed to the POP server. POP servers are used when the user is not permanently connected to the Internet.
Technical Bulletin Model: Bellini-C2 Date: 24-Apr-03 PAGE: 5/5 No.: RB070003 4. Check or change the SP value in accordance with the following table. SP Number 5852-002 Check / Change Check: The port number should be the same as the port number on the NIB summary report. If they are different, change the port number in this SP to the number on the NIB summary report. Note: This is just a confirmation, as the firmware update itself will not change the SMTP port number.
Technical Bulletin Model: Bellini-C2 Date: 26-May-03 Subject: Service Manual Revision PAGE: 1/16 No.: RB070004 Prepared by: M.Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) What This Document Contains This document summarizes the corrections in the Service Manual for “Model B-C2 (Machine Code: B070/B071).
1. Installation Pg. 1-20 1-20, 2, 2) 1-86 Old Initializing Toner Supply 1) Use the keys displayed on the screen to enter the developer lot no., then press !. 256 MB Memory Kit (B585) 1-87 1.12.7 Copier Connection Kit (B328) New/Action Initializing Developer Supply 1) Use the keys displayed on the screen and the numeric keys on the LCD to enter the developer Lot No., then press !. Deleted this page.
Preparation Before you begin the installation procedure, you must first: • Determine the distance between the machines to be connected. • Determine whether the printer/scanner option is installed on the machines. • Measure the distance between the machines, then decide how many cables and repeater hubs are required. DISTANCE Up to 4.5 m (14.8 ft.) 4.5 ~ 9.0 m (14.8 ~ 29.5 ft) 9.0 ~ 13.5 m (29.5 ~ 112.5 ft.
Installation Procedure "CAUTION Switch the machine off and unplug the machine before starting the following procedure. [B] [C] [A] T03040802.WMF 1. Switch the main power switch off. 2. Remove the controller box cover. (! x7) 3. Remove the cover [A] from slot A2. 4. Align the PCB with the bottom groove, and push the connection PCB [B] into the slot. NOTE: Make sure that the edge of the PCB is in the groove before you push the card into the machine. 5. Fasten the PCB with the attached screws [C].
[A] [C] [E] [D] [F] [B] T03040803.WMF 6. Connect the power repeater cable [A] to the mother board at CN149. 7. Connect the other end of the power repeater cable to the connection PCB [B]. 8. Insert the 64 MB SDRAM DIMM [C] into the slot on the mother board. • Set the edge connector at a 45 degree angle with the slot on the edge connector [D] aligned with the post below. • Press down slightly then push the DIMM toward the mother board until it snaps into place.
[A] [D] [E] [B] [C] T03040804.WMF 11. Insert one end of the interface cable [A] to the connection PCB inserted in slot A2. 12. If additional interface cables are required, connect the cables [B] with the repeater hubs [C]. 13. On the operation panel of both machines, remove the second cover (or Printer key) from the bottom [D]. 14.
3. REPLACEMENT AND ADJUSTMENT Pg. 3-125 Old 7. Energize the toner bank motor and toner supply coil clutch for 2 minutes with SP5804 070 and 071 to remove all of the toner in the supply path. New/Action 7. Switch on the machine and execute SP2226 to discharge toner from the toner bank.
4. TROUBLESHOOTING Pg. 4-1 Old Remove the old definition table. See below. New/Action Add the new definition table. See below. << Old >> There are 4 levels of service call conditions. Level A B C D Definition To prevent the machine from being damaged, the SC can only be reset by a service representative (see the note below). The copier cannot be operated at all. The SC can be reset by turning the main power switch off and on if the SC was caused by incorrect sensor detection.
Pg. 4-28 Old SC593 is not mentioned. New/Action Added SC593. See below. << New >> SC593: Replace the Toner Suction Motor Definition [B] The operation time of the motor is over 600 hours. Possible Cause • Service life of the toner suction motor is finished. Note: A near-end message is displayed in the LCD when the operation time exceeds 570 hours.
5. Service Tables Pg. 5-23 SP3903 5-24 5-25 5-49 SP5857 002 5-128 to 133 Old New/Action Adjusts the starting point for the VD Correction. Displays whether the VD correction is being performed. The target value for VD correction is “the value of SP2-001-7 + 50”. [0~999 / 200 / 1 K copies] DFU Adjusts the starting point for the VD Correction. Displays whether the VD correction is being performed. The target value for VD correction is “the value of SP2001-7 + 50”.
2. Under “5857 Save Debug Log”, touch “1 On/Off”. COPY : SP-5-857-001 Save Debug Log On/Off (1:ON 0:OFF) _1_ Initial 0 3. On the control panel keypad, press “1” then press !. This switches the Save Debug Log feature on. NOTE: The default setting is “0” (OFF). This feature must be switched on in order for the debug information to be saved.
4. Next, select the target destination where the debug information will be saved. Under “5857 Save Debug Log”, touch “2 Target”, enter “2” with the operation panel key to select the hard disk as the target destination, then press !. COPY : SP-5-857-002 Save Debug Log Target (2:HDD 3:SD Card) _2_ Initial 2 NOTE: Select “3 SD Card” to save the debug information directly to the SD card if it is inserted in the service slot. 5. Now touch “5858” and specify the events that you want to record in the debug log.
6. Next, select the one or more memory modules for reading and recording debug information. Touch “5859”. Under “5859” press the appropriate key item for the module that you want to record. Enter the appropriate 4-digit number, then press !. NOTE: Refer to the two tables below for the 4-digit numbers to enter for each key. The example below shows “Key 1” with “2222” entered. COPY : SP-5-859-001 Debug Save Key No. Key 1 ___2222 The following keys can be set with the corresponding numbers.
Please keep the following important points in mind when you are doing this setting: • Note that the number entries for Keys 1 to 5 are the same for the Copy, Printer, Scanner, and Web memory modules. • The initial settings are all zero. • These settings remain in effect until you change them. Be sure to check all the settings, especially the settings for Keys 6 to 10. To switch off a key setting, enter a zero for that key.
5.16.2 Retrieving the Debug Log from the HDD Retrieve the debug log by copying it from the hard disk to an SD card. 1. Insert the SD card into the service slot of the copier. 2. Enter the SP mode and execute SP5857 009 (Copy HDD to SD Card (Latest 4 MB)) to write the debugging data to the SD card. 3. After you return to the service center, use a card reader to copy the file and send it for analysis to Ricoh by email, or just send the SD card by mail. 5.16.
6. Details Pg. 6-11 6-66 6-66 6-68 6-68 6-68 Old “S54 Drum Temperature Sensor” 4. Readout from the drum potential sensor is used to adjust: •Development bias (Vb) • Grid voltage (Vg) • Laser diode (LD) power. NOTE: These calibrations are used to determine toner supply, so it is very important that the developer be initialized with SP2801 (TD Sensor Initialization) at installation and when the developer is replaced. 3. Vd should be –800 ± 20V.
Technical Bulletin Model: Bellini-C2 Date: 29-May-03 Subject: Installation Procedure For Copy Connection Kit PAGE: 1/8 No.: RB070005 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) The following is the revised version of the Installation Procedure (S/M pg.
Copier Connection Kit B328 (Machine Code: B070/B071) Subject to change Ricoh Technical Service May 2003
Connection Kit B328 Introduction The B070 (90 cpm)/B071 (105 cpm) machines can be connected with the new Copier Connection Kit B328 to increase the rate of copying. The copy rate doubles after both machines start printing. The copiers can be used for copy jobs only, not print jobs. However, documents stored on the document server beforehand can be printed with the connected copiers.
Installation Accessories Check the quantity and condition of the accessories in the box against the following list: 1 3 2 4 7 6 Description 5 T03040801E.WMF Q’ty 1. Interface Cable 1394............................................................. 3 2. Repeater Hub 1394............................................................... 2 3. Connection PCB ................................................................... 2 4. Power Repeater Cable .......................................................
Preparation Before you begin the installation procedure, you must first: • Determine the distance between the machines to be connected. • Determine whether the printer/scanner option is installed on the machines. Measure the distance between the machines, then decide how many cables and repeater hubs are required. DISTANCE Up to 4.5 m (14.8 ft.) 4.5 ~ 9.0 m (14.8 ~ 29.5 ft) 9.0 ~ 13.5 m (29.5 ~ 112.5 ft.
Installation Procedure !CAUTION Switch the machine off and unplug the machine before starting the following procedure. [B] [C] [A] T03040802.WMF 1. Switch the main power switch off. 2. Remove the controller box cover. (! x7) 3. Remove the cover [A] from slot A2. 4. Align the PCB with the bottom groove, and push the connection PCB [B] into the slot. NOTE: Make sure that the edge of the PCB is in the groove before you push the card into the machine. 5. Fasten the PCB with the attached screws [C].
[A] [C] [E] [D] [F] [B] T03040803.WMF 6. Connect the power repeater cable [A] to the mother board at CN149. 7. Connect the other end of the power repeater cable the connection PCB [B]. 8. Insert the 64 MB SDRAM DIMM [C] into the slot on the mother board. • Set the edge connector at a 45 degree angle with the slot on the edge connector [D] aligned with the post below. • Press down slightly then push the DIMM toward the mother board until it snaps into place.
[A] [D] [E] [C] [B] T03040804.WMF 11. Insert one end of the interface cable [A] to the connection PCB inserted in slot A2. 12. If additional interface cables are required, connect the cables [B] with the repeater hubs [C]. (☛1.3.2) 13. On the operation panel of the both machines, remove the second cover (or Printer key) from the bottom [D]. 14.
Technical Bulletin Model: Bellini-C2 Date: 26-Jun-03 Subject: Installation Procedure for MLB PAGE: 1/1 No.: RB070006 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) The following is the revised version of the Installation Procedure (S/M pg.
MLB (File Format Converter) - B609 Accessories Description Q’ty MLB Board (File Format Converter)............................................ 1 Installation [B] [A] B580I111.WMF 1. Make sure the following firmware versions are already installed: ! LCDC (NA): v2.09 (B0705374) or later ! LCDC (EU): v2.09 (B0705375) or later ! BIOS: VK02EL00O (B0705742D) or later ! Printer: v1.13 (B5806515) or later ! Scanner: v2.00 (B5806520) or later ! WebSystem: v2.00 (B0705757) or later 2. Turn OFF the main switch.
6. Install the following firmware together as a set: # # # # NCS (NIB): (B0705755B) Netfile: (B0705756B) System: (B0705754B) Webdoxbox: (B0705758B) v.4.15 v3.07.2 v4.01.4 v1.08 Important: The MLB functions will not work properly unless all versions above are installed together. 7. After successfully installing the firmware above, turn the main switch OFF/ON. 8. Set the following SP modes to the values shown: SP No. SP5-836 001 SP5-836 002 SP5-836 072 SP5-836 073 Setting 0 0 0 0 SP No.
9. Set the following SP modes as necessary, in accordance with the customer’s needs. SP No. SP5-836 094 Setting 2 0 SP-5836 098 1 0 Comments Sets JPEG2000 (J2K) as the file format for documents copied from the Document Server to Palm2. Note: Files backed up to Palm2 in J2K format cannot be edited by other software applications. Sets TIFF as the file format for documents copied from the Document Server to Palm2.
Technical Bulletin PAGE: 1/4 Reissued: 2-Jul-03 Model: Bellini-C2 Date: 26-Jun-03 No.: RB070006a RTB Reissue Step 8 has been added to the following procedure. Subject: Installation Procedure for MLB Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept.
MLB (File Format Converter) - B609 Accessories Description Q’ty MLB Board (File Format Converter)............................................ 1 Installation [B] [A] B580I111.WMF 1. Make sure the following firmware versions are already installed: ! LCDC (NA): v2.09 (B0705374) or later ! LCDC (EU): v2.09 (B0705375) or later ! BIOS: VK02EL00O (B0705742D) or later ! Printer: v1.13 (B5806515) or later ! Scanner: v2.00 (B5806520) or later ! WebSystem: v2.00 (B0705757) or later 2. Turn OFF the main switch.
6. Install the following firmware together as a set: # # # # NCS (NIB): (B0705755B) Netfile: (B0705756B) System: (B0705754B) Webdoxbox: (B0705758B) v.4.15 v3.07.2 v4.01.4 v1.08 Important: The function will not work properly unless all versions above are installed together. 7. After successfully installing the firmware above, turn the main switch OFF/ON. 8. Set SP5836-003 to a value of 1, which will enable the print back-up feature. 9. Set the following SP modes to the values shown: SP No.
SP No. Setting 0 Comments Does not apply the above correction to files copied to Palm2. Note: Use this setting for customers who wish to preserve the original reproduction level, especially with J2K files, and do not mind the time and disk space required for copying.
Technical Bulletin Model: Bellini-C2 PAGE: 1/5 Date: 3-Jul-03 Subject: Auto Process Control Summary for Bellini-C2 No.: RB070007 Prepared by: M.Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) The following is a summary of Auto Process Control on the Bellini-C2.
Auto Process Control: Bellini-C2 Note: The following explanation applies to the B-C2 and B-C1a/b/c/d, except for the values that differ from model to model mentioned in Section 4. ! Execution Conditions There are three separate cases in which the machine performs Auto Process Control: 1. When it is executed manually from SP2962 (Auto Process Control Execution). 2. When SP3901-001 (Auto Process Control Setting) has been set to ON, and the fusing temperature is detected at 100oC or less at power up.
" What Happens During Auto Process Control Auto Process Control is performed in the following order (Steps 1–5). Step Item Purpose 1 Drum potential sensor calibration 2 ID sensor adjustment To calibrate the drum potential sensor so that it will correctly detect VD and VH in Steps 3 and 4. To adjust Vsg to within the target range for Vref calculation in Step 5. What Happens The machine applies –200V then –700V to the OPC surface, and the drum potential sensor takes readings both times.
Step 3 Item Purpose VG adjustment To determine the VG (grid voltage) that will be used during copying\printing. 4 LD power adjustment 5 ID pattern creation, detection This is necessary as the sensitivity of the OPC surface can change when not used for an extended period, and because the charge casing and grid plate can become dirtied. To determine the LD light intensity that will be used for halftone areas during copying/printing. To update Vref for accurate toner density control.
Note on VD correction: As the development sleeve accumulates toner over time, the gap between VD and VB decreases, which makes it easier for dirty background to occur. To compensate for this, the machine increases the target VD value to -850±20V when the number of copies exceeds the value set with SP3903-1: VD Correction Counter, (default: 200K). As a result, VD increases and the VD-VB gap is maintained. This value is cleared when the developer is replaced and initialized.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 9-Jul-03 Subject: Firmware History (Bellini-C2 BIOS) No.: RB070008 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 BIOS. B0705742 Version C.
Technical Bulletin Model: Bellini-C2 PAGE: 1/2 Date: 9-Jul-03 Subject: Firmware History (Bellini-C2 NCS(NIB)) No.: RB070009 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 NCS (NIB). B0705735 Version C.
Technical Bulletin Model: Bellini-C2 Date: 9-Jul-03 PAGE: 2/2 No.: RB070009 Symptom Corrected 1. Modified for use with the MLB option (File Format Converter). 2. The hop count was mistakenly set at 4, making it impossible to obtain an auto IP address when there are four or more routers between the unit and the DHCP server (Hop count corrected to 64).
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 9-Jul-03 Subject: Firmware History (Bellini-C2 Netfile) No.: RB070010 Prepared by: M.Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 Netfile. B0705736 B0705756 A B Version C.SUM Production V1.
Technical Bulletin Model: Bellini-C2 PAGE: 1/2 Date: 9-Jul-03 Subject: Firmware History (Bellini-C2 System) No.: RB070011 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 System. B0705734 Version C.SUM Production A B V1.02.1 V1.
Technical Bulletin Model: Bellini-C2 Date: 9-Jul-03 PAGE: 2/2 No.: RB070011 Symptom Corrected 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Modified for use with the MLB option (File Format Converter). New default value for SP5-836-098 (Back Projection Removal): 1 “Please Wait” display does not clear when turning the power ON after installing a new HDD. “Please Wait” display does not clear during warm-up. Key sound and subsequent screen change for Designate key is slow.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 9-Jul-03 Subject: Firmware History (Bellini-C2 Webdocbox) No.: RB070012 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 Webdocbox. B0705738 Version C.SUM Production - V1.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 9-Jul-03 Subject: Firmware History (Bellini-C2 Websystem) No.: RB070013 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 Websystem. B0705737 Version C.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 9-Jul-03 Subject: Firmware History BCU No.: RB070014 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 BCU. B0705254 Version C.SUM Production A B V3.02 V4.01.1 V4.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 9-Jul-03 Subject: Firmware History (Bellini-C2 LCDC) No.: RB070015 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 LCDC. B0705371 (NA) B0705372 (EU) A B Version C.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 9-Jul-03 Subject: Firmware History Language No.: RB070016 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 Language. B0705350 Version C.SUM Production A V2.99 V3.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 9-Jul-03 Subject: Firmware History (Bellini-C2 Scanner) No.: RB070017 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 Scanner. B5806420 B5806520 Version C.SUM Production V1.
Technical Bulletin PAGE: 1/1 Reissued: 10-Jul-03 Model: Bellini-C2 Date: 9-Jul-03 No.: RB070018a MB Correction The items in bold italics have been corrected or added. Prepared by: M. Matsuda Subject: ROM History for SR840 From: 2nd Tech Support Sec. Service Support Dept.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 04-Aug-06 RTB Reissue The items in bold italics have been added. Subject: Firmware History (Bellini-C2 PS3) No.: RB070019a Prepared by: S.Ishizu From: Technical Services sec. Service Planning Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Paper path Transmit/receive Retrofit information Other ( ) This is to inform you of the firmware history for the Bellini-C2 PS3.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 9-Jul-03 Subject: Firmware History (Bellini-C2 Printer) No.: RB070020 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 Printer. B5806415 Version C.SUM Production B5806515 V1.
Technical Bulletin PAGE: 1/2 Reissued: 16-Jul-03 Model: Bellini-C2 Date: 9-Jul-03 No.: RB070018b MB Correction The items in bold italics have been corrected or added. Subject: ROM History for SR840 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept.
Technical Bulletin PAGE: 2/2 Reissued: 16-Jul-03 Model: Bellini-C2 Date: 9-Jul-03 No.
Technical Bulletin Model: Bellini-C2 PAGE: 1/2 Date: 24-Jul-03 Subject: Notes for EB-105EX Installation No.: RB070021 Prepared by: Chisato Tsuji From: 1st Tech. Support Sec. Service Support Dept.
Technical Bulletin Model: Bellini-C2 Date: 24-Jul-03 PAGE: 2/2 No.: RB070021 Future use with the SR860 booklet finisher (B468) At present, the EB105EX controller does not support use with the SR860 booklet finisher due to paper jams that sometimes occur with the current system software. The patch file is currently being created to support this finisher. However, until the official release please do not install this controller on machines using the SR860.
Technical Bulletin Model: Bellini-C2 Date: 20-Aug-03 Subject: New SP (SP6903/6120) PAGE: 1/1 No.: RB070022 Prepared by: Y.Urushihara From: 1st Tech. Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) Please be sure to see the firmware requirements. 1.
Technical Bulletin Date: 28-Aug-03 Model: Bellini-C2 Subject: LD Unit Adjustment Procedure PAGE: 1/2 No.: RB070023 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept.
Technical Bulletin Model: Bellini-C2 Date: 28-Aug-03 PAGE: 2/2 No.: RB070023 LD Unit Adjustment Procedure Please perform the following if the spacers attached to the bottom of the LD unit are misplaced or their original positions become unclear at LD unit replacement. This adjustment is necessary to ensure ID variations along the main scan direction do not occur, which result from beam pitch variations along the sub-scan direction.
Technical Bulletin Model: Bellini-C2 Date: 1-Sep-03 Subject: File Format Converter supports DTB V2 from PAGE: 1/1 No.: RB070024 Prepared by: K. Ichihara v3.0.0.0, error message unclear From: NS Support Sec. Service Support Dept.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 12-Sep-03 Subject: Patch Release for EB-105EX (1-AKVJG) No.: RB070025 Prepared by: Chisato Tsuji From: 1st Tech. Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is a release note for a patch file for printer controller EB-105EX.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 3-Oct-03 Subject: Firmware History BCU No.: RB070026 Prepared by: C. Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 BCU. B0705254 Version C.SUM Production A B C V3.02 V4.01.1 V4.05 V.4.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 10-Oct-03 Subject: Firmware History (Bellini-C2 Netfile) No.: RB070027 Prepared by: C.Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 Netfile. B0705736 B0705756 A B D Version C.
Technical Bulletin Model: Bellini-C2 PAGE: 1/2 Date: 10-Oct-03 Subject: Firmware History (Bellini-C2 System) No.: RB070028 Prepared by: C.Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 System. B0705734 Version C.SUM Production A B V1.02.1 V1.04.
Technical Bulletin Model: Bellini-C2 Date: 10-Oct-03 PAGE: 2/2 No.: RB070028 Symptom Corrected 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Modified for use with the MLB option (File Format Converter). New default value for SP5-836-098 (Back Projection Removal): 1 “Please Wait” display does not clear when turning the power ON after installing a new HDD. “Please Wait” display does not clear during warm-up. Key sound and subsequent screen change for Designate key is slow.
Technical Bulletin Model: Bellini-C1/C2 Date: 31-Oct-03 Subject: Toner Scattering at rear side of the machine PAGE: 1/7 No.: RB070029 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) SYMPTOM 1. Toner scattering in the rear of the machine 2.
Technical Bulletin Model: Bellini-C1/C2 PAGE: 2/7 Date: 31-Oct-03 No.: RB070029 SOLUTION IMPORTANT: Check the following items before performing the solution below. 1. Check the toner filter [A] and drum filter [B], and clean or replace them as necessary. Note: The toner filter should be replaced every 300k (Bellini-C1) or 350k (Bellini-C2).
Technical Bulletin Model: Bellini-C1/C2 Date: 31-Oct-03 PAGE: 3/7 No.: RB070029 b) Attach the Mylar (B0703618) to the top of the toner recycling case as shown below. This will prevent toner scattering at the connection between the transfer unit toner collection pipe and recycling case.
Technical Bulletin Model: Bellini-C1/C2 PAGE: 4/7 Date: 31-Oct-03 No.: RB070029 c) Attach the new seal (B0703619) as shown below to the opening in the rear side plate. This will prevent toner scattering in the fusing and duplex areas.
Technical Bulletin Model: Bellini-C1/C2 PAGE: 5/7 Date: 31-Oct-03 No.: RB070029 2. Toner scattering from the filters of the toner hopper a) The material of the cylinder case seal (A2943476) has been changed to one with higher reliability (from Aug ’02 production). Note: It is easier to replace the entire cylinder case (A2943485). b) Clean the tube (A2943071) between the toner hopper and the cylinder case (procedure below).
Technical Bulletin Model: Bellini-C1/C2 Date: 31-Oct-03 PAGE: 6/7 No.: RB070029 Tube Cleaning Procedure 1. Remove the development unit. 2. Remove the right upper cover and cylinder case bracket. 3. Disconnect the tube (A2943071) from the cylinder case. 4. Remove any clogged toner through the upper hole of the tube joint using a vacuum cleaner.
Technical Bulletin Model: Bellini-C1/C2 PAGE: 7/7 Date: 31-Oct-03 No.: RB070029 Cut-in Serial Numbers TBA RCL (Japan) Production (B070/B071) MODEL NAME Ricoh Aficio 2090 Savin 4090 Gestetner 9002 Lanier LD 090 Gestetner 9002 Nashatec 9005 Rex Rotary 9008 Lanier LD 090 IS 2090 Ricoh Aficio 2090 Ricoh Aficio 2105 Savin 40105 Gestetner 10512 Lanier LD 0105 Gestetner 10512 Nashatec 10515 Rex Rotary 10518 Lanier LD 0105 IS 2105 Ricoh Aficio 2105 V/Hz 208 - 240V/60Hz DESTINATION USA, Canada.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 6-Nov-03 Subject: EB-105EX Service Manual Correction No.: RB070030 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) Please correct your EB-105EX service manual as follows: Page Incorrect Correct Note 1-8 6. Insert the extension card 6.
Technical Bulletin Model: Bellini-C2 Date: 7-Nov-03 Subject: Installation Procedure For Tray Heater Kit PAGE: 1/5 No.: RB070031 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This bulletin describes the installation procedure for the tray heater kit for the Bellini-C2 mainframe.
Technical Bulletin Model: Bellini-C2 Date: 7-Nov-03 Installation Procedure CAUTION: Make sure to turn the machine OFF before installation 1. Remove all trays, middle rail for tandem tray and harness cover as shown 2. Open the controller box. Then remove the lower rear cover and PSU. 3. Attach the lower tray heater with 3 screws. PAGE: 2/5 No.
Technical Bulletin Model: Bellini-C2 Date: 7-Nov-03 PAGE: 3/5 No.: RB070031 4. Attach the upper tray heater kit to the middle rail for the tandem tray with 2 screws. 5. Install the middle rail and upper tray heater kit into the main frame Front Side: Fixed with 3 screws Rear Side: Fixed with 2 screws Insert the hook of the heat sink here!! 6. Place the harness for upper and lower heaters as shown Note: Clamp the harness for the upper heater at 2 points.
Technical Bulletin Model: Bellini-C2 Date: 7-Nov-03 7. Connect both connectors at the rear side of the machine. Note: The connectors are identical, so you do not need to worry about connecting them the wrong way round. 8. Attach the harness cover. Note: Make sure not to pinch the harness when the cover is attached. Front view Rear view Insert the harness hook cover here. PAGE: 4/5 No.
Technical Bulletin Model: Bellini-C2 Date: 7-Nov-03 PAGE: 5/5 No.: RB070031 9. Plug in the connector for the anti-condensation heater to the AC drive board as shown in Fig.1. !CAUTION All anti-condensation heaters are disconnected from the AC drive board before shipping. Before plugging in the AC harness connector, make sure that the main switch of the copier is switched off and the power cord unplugged. Note 1: The connector is hung on the clamp under the AC drive board.
Technical Bulletin Model: Bellini-C2 PAGE: 1/2 Date: 11-Nov-03 Subject: Jam Code 53 No.: RB070032 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) Please also see page 2 below for more details on the following. SYMPTOM Jam code 53 sometimes occurs when LT LEF is fed from the tandem tray.
Technical Bulletin Model: Bellini-C2 Date: 11-Nov-03 PAGE: 2/2 No.: RB070032 Tandem Tray Paper Feed Sensor Jam # Symptom: Feed sensor jam from mis-feed of 3 or more sheets. Before the trailing edge of the first sheet clears the feed/reverse rollers, the pickup roller, (already rotating) from drive supplied through the feed roller, lowers and begins feeding the next sheet. Then the trailing edge of the first sheet crosses with the leading edge of the next sheet around the area of the feed sensor.
Technical Bulletin Model: Bellini-C2 PAGE: 1/3 Date: 26-Nov-03 Subject: Firmware History (Bellini-C2 System) No.: RB070033 Prepared by: C.Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 System. B0705734 Version C.SUM Production A B V1.02.1 V1.04.
Technical Bulletin Model: Bellini-C2 Date: 26-Nov-03 PAGE: 2/3 No.: RB070033 Symptom Corrected 1. Modified for use with Copy Connector Kit. 2. SC997/SC998 occurs with frequent use of New Job. 3. The Printer function is given priority when the Copier is set as the priority function. 4. Modified to further minimize multifeeds for certain paper types. Suffix A 5. Paper is stacked in shift tray 2 when center stapling is disabled and the job resumed following a center staple End condition. 1.
Technical Bulletin Model: Bellini-C2 Date: 26-Nov-03 PAGE: 3/3 No.: RB070033 Symptom Corrected 1. Modified for use of the EB-105EX in combination with Desk Top Editor for Production. 2. SC955 may occur when printing out a Document Server file from the operation panel in Magazine mode if the file 1) contains blank page(s), and 2) was originally stored to the Document Server via a GW controller. 3.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 26-Nov-03 Subject: Firmware History (Bellini-C2 Netfile) No.: RB070034 Prepared by: C.Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the firmware history for the Bellini-C2 Netfile. B0705736 B0705756 A B D E Version C.
Technical Bulletin Model: Bellini-C1/C2 Date: 5-Dec-03 Subject: Seal Improvement in Toner Bank Unit PAGE: 1/4 No.: RB070035 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) SYMPTOM The following sometimes occur: 1. Misdetection of the waste toner bottle full condition 2.
Technical Bulletin Model: Bellini-C1/C2 Date: 5-Dec-03 PAGE: 2/4 No.: RB070035 SOLUTION The following solutions have been applied from October ’03 production. 1. Misdetection of the waste toner bottle Full condition 1. A toner catcher has been added to the toner bank case as shown below. Toner Catcher 2. A seal has been added to the toner bank base plate, preventing toner from scattering out of this area. - P/N: B0703364 (Shield: Bracket Chuck) - Attachment position: Refer to Parts Catalog, pg.
Technical Bulletin Model: Bellini-C1/C2 PAGE: 3/4 Date: 5-Dec-03 No.: RB070035 2. Toner bottle cannot be pulled out from the toner bank unit Two kinds of the shields have been added to ensure toner does not leak out from the toner bottle.
Technical Bulletin Model: Bellini-C1/C2 PAGE: 4/4 Date: 5-Dec-03 No.: RB070035 RCL (Japan) Production (B070/B071) MODEL NAME Ricoh Aficio 2090 Savin 4090 Gestetner 9002 Lanier LD 090 Gestetner 9002 Nashatec 9005 Rex Rotary 9008 Lanier LD 090 IS 2090 Ricoh Aficio 2090 Ricoh Aficio 2105 Savin 40105 Gestetner 10512 Lanier LD 0105 Gestetner 10512 Nashatec 10515 Rex Rotary 10518 Lanier LD 0105 IS 2105 Ricoh Aficio 2105 V/Hz 208 - 240V/60Hz DESTINATION USA, Canada. South America CODE B070-17 SERIAL NO.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 18-Dec-03 Subject: Patch Release for EB-105EX (1-9ZUYT) No.: RB070036 Prepared by: Chisato Tsuji From: 1st Tech. Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) The following is a patch file release note for the EB-105EX printer controller.
Technical Bulletin Model: Bellini-C2 Date: 23-Jan-04 Subject: Protection Seal PAGE: 1/2 No.: RB070037 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept.
Technical Bulletin Model: Bellini-C2 PAGE: 2/2 Date: 23-Jan-04 Controller Box Positioning Bracket Attachment Position for the Temporary Protective Seal Front View Rear View No.
Technical Bulletin Model: Bellini-C2 Date: 4-Feb-04 Subject: Information for Bellini-C2 Enhanced Version PAGE: 1/15 No.: RB070038 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept.
Technical Bulletin Model: Bellini-C2 PAGE: 2/15 Date: 4-Feb-04 No.: RB070038 Major Differences Between the Bellini-C2 and Bellini-C2e I. OPC Drum (Production Line) The OPC layer of the drum has been thickened, so the lifetime of the OPC drum has been increased. The following drum is fitted in C2e mainframes on the production line, but as service parts, it can also be used on C2 MIF (see point 5) below). 1) C2e Drum P/N: B0709510 2) Lot No.
Technical Bulletin Model: Bellini-C2 PAGE: 3/15 Date: 4-Feb-04 No.: RB070038 4) Setting Powder (P/N 54429101) for the new C2e drum: This drum surface setting powder should be applied whenever installing the service parts C2e drum in the field. Please be sure to see pg. 2 of RTB #RA294064 for the application procedure and related notes.
Technical Bulletin Model: Bellini-C2 Date: 4-Feb-04 PAGE: 4/15 No.: RB070038 2) Service Manual/Parts Catalog a) Z-Folding Unit Service Manual: Released to the RISSN Server in early Feb ‘04 as an insert version. Parts Catalog: Released to the RISSN Server in mid-Feb ‘04 as an insert version. b) 3000-Sheet Finisher Service Manual: (see Appendix below). Parts Catalog: Released to the RISSN Server in mid-Feb ‘04 as an insert version.
Technical Bulletin Model: Bellini-C2 PAGE: 5/15 Date: 4-Feb-04 No.: RB070038 b) Finisher Input Check: SP6117. The sensors in bold have been added. Class Bit 3 No. No.
Technical Bulletin Model: Bellini-C2 003 Back – On/Off Setting 004 Back – On/Off Timing Adj. 005 Front – On/Off Setting: Low Speed Mode 006 Front – Off Timing Adj.: Low Speed Mode 007 Back– On/Off Setting: Low Speed Mode 008 Back – Off Timing Adj.: Low Speed Mode Date: 4-Feb-04 PAGE: 6/15 No.: RB070038 Switches the PTL on and off for the rear side of the paper passing through the fusing unit in the duplex mode at normal speed.
Technical Bulletin Model: Bellini-C2 PAGE: 7/15 Date: 4-Feb-04 No.: RB070038 2) LD Units: SP2115-007 has been newly added to increase the accuracy of the LD beam pitch. To activate this SP mode, it is necessary to manually input the value shown at the bottom right of the label (see below) when replacing the LD unit. New value for SP2115-007 manual input New decal on the LD unit SP2115 001/SP2115 002/SP2115 003 PS2115 004/SP2115 005/SP2115 006/SP2115 007 B070R978.
Technical Bulletin Model: Bellini-C2 Date: 4-Feb-04 PAGE: 8/15 No.: RB070038 APPENDIX SR841 Service Manual Differences The following is a summary of the differences between the SR840 and SR841 (all other sections are identical). The revised sections appear from the following page. Installation Auxiliary trays and their holders have been added to the accessory list.
Technical Bulletin Model: Bellini-C2 PAGE: 9/15 Date: 4-Feb-04 No.: RB070038 Installation Accessory Check Check the quantity and condition of the accessories in the box against the following list: Description Q’ty 1. Cushion ............................................................................... 1 2. Table Extension................................................................... 1 3. Leveling Shoes.................................................................... 4 4. Rear Joint Bracket .
Technical Bulletin Model: Bellini-C2 PAGE: 10/15 Date: 4-Feb-04 Replacement and Adjustment Z-Fold Jogger unit Cover [B] [A] Ｂ706Ｒ101.WMF 1. Open the front door. 2. Pull out the stapler tray unit [A]. 3. Remove the Z-fold jogger unit cover [B] (! x2) No.
Technical Bulletin Model: Bellini-C2 Date: 4-Feb-04 PAGE: 11/15 No.: RB070038 Jogger Top Fence Motor [A] [B] Ｂ706Ｒ102.WMF 1. Open the front door and pull out the stapler tray unit. 2. Remove the Z-fold jogger unit cover (! x2) 3. Remove the motor bracket [A] (! x2, timing belt x1) 4.
Technical Bulletin Model: Bellini-C2 PAGE: 12/15 Date: 4-Feb-04 No.: RB070038 Z-Fold Jogger Unit [A] Ｂ706Ｒ103.WMF 1. Open the front door and pull out the stapler tray unit. 2. Remove the Z-fold jogger unit cover (! x2) 3.
Technical Bulletin Model: Bellini-C2 PAGE: 13/15 Date: 4-Feb-04 No.: RB070038 Jogger Bottom Fence Motor [A] B706R104.WMF 1. Open the front door and pull out the stapler tray unit. 2. Remove the jogger bottom fence motor [A] (! x2, timing belt x1, " x1, # x1).
Technical Bulletin Model: Bellini-C2 PAGE: 14/15 Date: 4-Feb-04 No.: RB070038 Details Stapling Z-Folded Paper ⑥ ⑦ ⑧ B674D004.WMF B674D005.WMF Here is the operation sequence for jogging and stapling Z-folded sheets: ① The lower jogger fence lifts to receive the Z-folded sheets. ② The top fence moves down, to the horizontal position. ③ A sheet of paper goes into the stapler tray. ④ The positioning roller turns when each sheet is fed to the stapler tray.
Technical Bulletin Model: Bellini-C2 PAGE: 15/15 Date: 4-Feb-04 No.: RB070038 Electrical Components 2 1 25 3 24 4 23 22 5 21 6 7 20 8 19 9 18 17 10 11 12 16 15 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
Technical Bulletin Model: Bellini-C1 Date: 23-Jan-04 Subject: OPC Drum Change/ Drum Setting Powder PAGE: 1/2 No.: RA294064 Prepared by: M.Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) Important Note: The OPC drum has been changed as follows, which requires the application of setting powder at drum installation.
Technical Bulletin Model: Bellini-C1 Date: 23-Jan-04 PAGE: 2/2 No.: RA294064 Important Note for Installation of the New Drum Since the smoothness of the new drum (without dichloromethane) is reduced, it is essential to make sure to apply Drum Setting Powder (P/N: 54429101) to the drum surface as shown below before installing. Note: If the setting powder is not applied, the drum’s cleaning blade may turn outward, causing a drum cleaning failure. Application Procedure for Drum Setting Powder 1.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 28-Apr-04 Subject: Firmware Update Remarks No.: RB070039 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 28-Apr-04 Subject: Error Code: E32, E44 Appeared No.: RB070040 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) SYMPTOM Error codes E32 and E44 are sometimes displayed when several types of firmware are installed at the same time.
Technical Bulletin Model: Bellini-C2 PAGE: 1/2 Date: 14-May-04 Subject: EB-105EX suddenly drops off the network. No.: RB070041 Prepared by: C.Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) SYMPTOM The EB-105EX suddenly drops off the network.
Technical Bulletin Model: Bellini-C2 PAGE: 2/2 Date: 14-May-04 No.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 14-May-04 Subject: Patch Release for EB-105EX (1-CX7BV) No.: RB070042 Prepared by: Chisato Tsuji From: 1st Tech. Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is a release note for a patch file for printer controller EB-105EX.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 14-May-04 Subject: Patch Release for EB-105EX (1-D3C5T) No.: RB070043 Prepared by: Chisato Tsuji From: 1st Tech. Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is a release note for a patch file for printer controller EB-105EX.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 14-May-04 Subject: Patch Release for EB-105EX (1-B952E_1- No.: RB070044 Prepared by: Chisato Tsuji BWIKW) From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is a release note for a patch file for printer controller EB-105EX.
Technical Bulletin PAGE: 1/1 Reissued: 29-Jun-04 Model: Bellini-C2 Date: 24-Jun-04 Subject: Patch Release for EB-105EX (1-DBI62) No.: RB070045a Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Paper path Transmit/receive Retrofit information Other ( ) RTB Reissue Procedure step 2 has been corrected. The patch should be downloaded to the “Direct” queue.
Technical Bulletin PAGE: 1/2 Reissued: 16-Sep-04 Model: Bellini-C2 Date: 21-Jul-04 No.: RB070046a RTB Correction The items in bold italics have been corrected or added. Prepared by: M. Matsuda Subject: LCDC Firmware Update Failure From: 2nd Tech Support Sec. Service Support Dept.
Technical Bulletin PAGE: 2/2 Reissued: 16-Sep-04 Model: Bellini-C2 Date: 21-Jul-04 No.: RB070046a LCDC Recovery Procedure IMPORTANT: If you are updating the machine from a Bellini-C2 to a Bellini-C2e (enhanced model), this recovery procedure will not work. In this case, replace the LCDC board. Reason: The recovery program is overwritten only when you update from the BC2 to the B-C2e. See RTB RB070039 for details about the B-C2e firmware. 1. Insert an SD card which contains the LCDC firmware. 2.
Technical Bulletin PAGE: 1/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 No.: RGene019a RTB Correction The items in bold italics have been corrected or added. Prepared by: H. Someya Subject: Remote Firmware Update From: 1st Tech. Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Paper path Transmit/receive Retrofit information Other ( ) 1.
Technical Bulletin PAGE: 2/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 No.: RGene019a The following models do not support RFU: • Printers: Model K-P1/P2, Model J-P1, Model A-P3, Model U-P1, Model AR-P1, and not GW products • MFPs: Model A-C2/C3, Model R-C2, Model U-C1, Model MT-C1, and not GW products 3. SYSTEM REQUIREMENTS Network Interface: • 10 Base-T or faster Ethernet LAN • IEEE1284 (Centronics) (A setting must be changed in SP mode.
Technical Bulletin PAGE: 3/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 No.: RGene019a Ftp settings and commands: • User name (default): Before 04A: rsysupdate 04A and later: admin • Password (default): Before 04A: password 04A and later: (no password) Note: These default passwords are the same as the administrator passwords. • • Transfer mode: binary FTP commands supported: binary (Transfer data in binary mode) dir (List files and directories) put “file name” get version.
Technical Bulletin PAGE: 4/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 No.: RGene019a 5. UPDATING PROCEDURE Recommendation: It is strongly recommended that RFU be performed on-site, to minimize the chances of a power-down during RFU. 5.1 Auto Rebooting After receiving new firmware, the machine firmware is updated and the machine is automatically rebooted using the updated firmware. Fig.2 shows the kind of reboot required after the firmware is updated.
Technical Bulletin PAGE: 5/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 No.: RGene019a 5.2 Preparation Before you update the firmware by RFU, carry out three items as shown below. 5.2.1 Checking the IP address For a machine with static IP address: • • • • Search for the IP address using SmartDeviceMonitor for Admin or Web SmartDeviceMonitor. If the hostname of the machine is registered in a DNS server, use the nslookup command with the machines hostname.
Technical Bulletin PAGE: 6/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 5.3 RFU for Windows 1. Open a command prompt. o [Start]-[Program]-[Accessories]-[Command Prompt] 2. Logon to the machine using ftp. C:\> ftp xxx.xxx.xxx.xxx Specify the machine's IP address Connected to xxx.xxx.xxx.xxx. 220 (Product name) FTP server (1.00)ready. User (IP address:(none)): 3. Enter the user name. User (IP address:(none)):rsysupdate User name 331 Password required for rsysupdate. Password: 4.
Technical Bulletin PAGE: 7/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 No.: RGene019a 6. Enter "get version.txt -" to check the machine's firmware version.f 200 PORT command successful. 150 Opening ASCII mode data connection for 'version.txt'. PartNo. Module Name Version Module ID ---------------------------------------------------------------------------------------------G0000000 os & copy 0.20 XXXXXX_copy G0000000 os & pf 0.20 XXXXXX_system G570xxxx Onboard Scn 2.
Technical Bulletin PAGE: 8/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 No.: RGene019a When the machine starts to receive the file, the following message appears on the machine's control panel and normal machine functions are disabled. o Display panel (MFPs) o Display (Printers) ROM Update Receiving Data 10. Once the machine has received the entire firmware module file, the firmware update starts automatically.
Technical Bulletin PAGE: 9/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 No.: RGene019a 11. After the firmware has been updated, the machine must restart. This may be automatic depending on the firmware and model. 12. Enter "bye" to exit ftp. ftp> bye C:\> 13. Check the firmware version as shown in step 6. 14. Update all required firmware by repeating steps 1 to 13 as necessary. 5.4 RFU for UNIX(LINUX) 1. Logon to the machine using ftp.
Technical Bulletin PAGE: 10/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 No.: RGene019a 5.5 Firmware Update for Centronics (IEEE1284) Note: • Firmware update via a centronics interface does not require a password. • The only method of recovery available via a centronics interface is an IC or SD card. 1. Check the target firmware version by printing out the SMC sheet with SP5-990-4. 2. Set SP5-856-2 to a value of 1. This will configure the machine for firmware update via the Centronics I/F.
Technical Bulletin PAGE: 11/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 No.: RGene019a 5.6 Checking the Result of the Update Check that the firmware has been updated. Note: • After transmitting the firmware file from the computer, it takes approximately 3 to 5 minutes for updating to complete and the machine to restart. • To check the result, you need to logon to the machine again using ftp.
Technical Bulletin PAGE: 12/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 No.: RGene019a 6. ERROR RECOVERY There are three ways to recover from a loss of power during RFU. 6.1 Recovery Procedure There are three types for recovery after a power loss during RFU. (This will depend on the firmware and model). Procedures for types 1, 2 and 3 are on the next page. Find the firmware and model you are downloading to, and begin with the type shown in the table below.
Technical Bulletin PAGE: 13/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 No.: RGene019a Important: Do not turn the main power off while you perform any of the procedures. Procedure for type 1: 1. Restore power to the machine. The machine will wait for the operator to start the update. 2. Connect to the machine by FTP and upload the *.rru or *.rfu files. Procedure for type 2: 1. Try ‘Procedure for type 1’. 2. If this does not work, restore power to the machine. 3.
Technical Bulletin PAGE: 14/15 Reissued: 15-Apr-05 Model: General RTB 7. Date: 15-Nov-04 No.: RGene019a TROUBLESHOOTING 7.1 Checking the error status You can check the error status using ftp. Check whether an error occurred by viewing errlog.txt. This file is in the same directory as version.txt. 1. Logon to the machine using ftp. 2. Enter "dir" to check that errlog.txt exists. ftp> dir 200 PORT command successful. 150 Opening ASCII mode data connection for '/'.
Technical Bulletin PAGE: 15/15 Reissued: 15-Apr-05 Model: General RTB Date: 15-Nov-04 No.: RGene019a 7.2 Error Code List Error Code 51 52 53 Description/Causes The machine cannot be updated. • The machine is processing a print job. • The machine is processing a scan job. • The machine is receiving image data from the network. • The control panel is in use. • The machine is sending or receiving a fax.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 21-Sep-04 Subject: ROM History for SR841 No.: RB070047 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the ROM history for the SR841 (VICTORIA-D). ROM No B7065105 B7065106 Main PCB No B7065130 B7065131 Version V1.10 V1.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 5-Oct-04 Subject: Patch Release for EB-105EX (1-DWZRP) No.: RB070048 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is a release note for a patch file for printer controller EB-105EX.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 5-Oct-04 Subject: Patch Release for EB-105EX (1-EG91P) No.: RB070049 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is a release note for a patch file for printer controller EB-105EX.
Technical Bulletin Model: Bellini-C2 Date: 18-Oct-04 Subject: SR850, SR860 Stapler Harness Damage PAGE: 1/2 No.: RB070050 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) SYMPTOM The outside of the stapler harness is damaged in the area shown in the photo.
Technical Bulletin Model: Bellini-C2 PAGE: 2/2 Date: 18-Oct-04 No.: RB070050 SOLUTION Permanent Solution The shape of the rear plate has been changed so that it does not touch the stapler harness (the cut-in serial number is in the table below). Action In The Field For machines produced before the cut-in serial numbers: Attach a piece of insulating tape to the area of the rear plate shown in the photo (red mark).
Technical Bulletin Model: Bellini-C2 Date: 5-Nov-04 Subject: ROM History for SR840 PAGE: 1/2 No.: RB070051 Prepared by: S. Ishizu From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This is to inform you of the ROM history for the SR840 (VICTORIA-B).
Technical Bulletin Model: Bellini-C2 Date: 5-Nov-04 PAGE: 2/2 No.: RB070051 Symptom Corrected 4. Poor stack sorting of individual N-jobs that use stapling/sorting. 5. The “Add more staples” display is not cleared even after loading new staples following a stapler-end. 1. Paper in the stacking unit is not lined up correctly. Conditions: - 2 A3 originals copied to 3 sets or more in Sorting mode - Occurs from the second sheet of the second set ROM No B4785112 2.
Technical Bulletin Model: Bellini-C2 PAGE: 1/4 Date: 8-Dec-04 Subject: EB-105EX System Ver.1.2 Release No.: RB070052 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Paper path Transmit/receive Product Safety Other ( Retrofit information ) EB-105EX version 1.2 has been released.
Technical Bulletin Model: Bellini-C2 Date: 8-Dec-04 PAGE: 2/4 No.: RB070052 • Supports Adobe PS Interpreter 3016 • Fiery WebSpooler is not supported anymore. Please use the Command WorkStation (Windows users) or Fiery Spooler (Macintosh users). • Supports Secure Print from copier With this feature, you can add a password to the print job when you send it to the EB-105EX from the Postscript printer driver. The job will stay in the copier until the password is input.
Technical Bulletin Model: Bellini-C2 PAGE: 3/4 Date: 8-Dec-04 No.: RB070052 3. Firmware Versions Required to Use System V1.2 with the Bellini-C2 To use System V1.2, make sure to install the following firmware: Language: BCU: SYSTEM: LCDC (NA): LCDC (EU): NIC (NIB): Netfile: WebSystem: WebDocbox: BIOS: Finisher SR841: Finisher SR860: Z-folding unit: V.3.10 (B0705350B) or newer V. 5.16.34 (B0705254E) or newer V. 5.04.2 (G0705774) or newer V. 2.18 (B0705374B) or newer V. 2.18 (B0705375B) or newer V.4.
Technical Bulletin Model: Bellini-C2 Date: 8-Dec-04 PAGE: 4/4 No.: RB070052 4. Overview of the V1.01 to V1.2 System Upgrade Procedure 1) Check the contents of the kit. - User Software CD-ROM V1.2.1 PCL driver CD-ROM V2.00 Document CD-ROM V1.20 Release Note *System Software CD-ROM V1.2.0 *FPGA Update Patch Rev. 1f CD-ROM Version-Up Instructions [G3536671C] [G3536691D] [G3536681D] [G3536731B] [G3536981A] [G3538921] [G3538911] Note* These CDs should be used by service personnel only.
Technical Bulletin Model: Bellini-C2 PAGE: 1/2 Date: 9-Dec-04 Subject: Boot SD Card for Bellini-C2 No.: RB070053 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) THE BELLINI-C2 BOOT SD C ARD A boot SD card was released as a service tool for the Bellini-C2 (P/N B6456080).
Technical Bulletin Model: Bellini-C2 Date: 9-Dec-04 PAGE: 2/2 No.: RB070053 6. Return the DIP SW4 #6 to the upper position. 7. Install the newest B-C2 enhanced firmware. Note: See RTB #RB070039 for details on the B-C2e. Important Notes 1. DO NOT delete or move the files stored on the boot SD card. These files are written to the boot SD card by a special factory device.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 16-Dec-04 Subject: Patch Release for EB-105EX V.1.2 (1-FY60I) No.: RB070054 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Mechanical Paper path Other ( Part information Electrical Transmit/receive Action required Service manual revision Retrofit information ) This RTB is the release note for Patch File 1-FY60I for EB-105EX printer controller System V1.2.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 16-Dec-04 Subject: Patch Release for EB-105EX V.1.2 (1-FH7LW) No.: RB070055 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This RTB is the release note for Patch File 1-FW7LW for EB-105EX printer controller System V1.2.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 7-Jan-05 Subject: Patch Release for EB-105EX V.1.2 (1-GRRLM) No.: RB070056 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This RTB is the release note for Patch File 1-GRRLM for EB-105EX printer controller System V1.2.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 7-Jan-05 Subject: Patch Release for EB-105EX V.1.2 (1-GYWYK) No.: RB070057 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This RTB is the release note for Patch File 1-GYWYK for EB-105EX printer controller System V1.2.
Technical Bulletin Model: Martini-C2 PAGE: 1/1 Date: 6-Jan-05 Subject: Information on using the finishers with MT-C2 No.: RB140024 Prepared by: S. Watanabe From: 2nd Tech Support Sec. Service Support Dept.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 25-Mar-05 Subject: Patch Release for EB-105EX V.1.2 (1-HG4WZ) No.: RB070058 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Transmit/receive Retrofit information Paper path Other ( ) This RTB is the release note for Patch File 1-HG4WZ for EB-105EX printer controller System V1.2.
Technical Bulletin Model: Bellini-C2 PAGE: 1/3 Date: 15-Apr-05 Subject: Printer Bit Switch Information No.: RB070059 Prepared by: M. Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Paper path Transmit/receive Product Safety Other ( Retrofit information ) Service Manual Revision The following printer bit switches were added to the Service Manual.
Technical Bulletin Model: Bellini-C2 SP Date: 15-Apr-05 Number/Bit Bit 3 003 004 005 Bit 4 Bit 5 Bit 6 Bit 7 Bit 0 Bit 1 Bit 2 PAGE: 2/3 No.: RB070059 Function Enables/Disables PDL switching (mid-job). 0: ON (Allows PDL switching) 1: OFF (Forbids PDL switching) DFU DFU DFU DFU DFU DFU Toggles the minimum value of the x coordinate (left margin) between 0 and 1. This is mainly used for compatibility with HP4000/HP8000. 0: OFF (Conventional spec.
Technical Bulletin Model: Bellini-C2 SP Number/Bit Bit 6 Bit 7 006 Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 007 Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 0 008 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Date: 15-Apr-05 Function DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU DFU PAGE: 3/3 No.
Technical Bulletin Model: Bellini-C2 PAGE: 1/1 Date: 04-Aug-06 RTB Reissue The items in bold italics have been added. Subject: Firmware History (Bellini-C2 Printer) No.: RB070020a Prepared by: S.Ishizu From: Technical Services sec. Service Planning Dept.
Technical Bulletin Model: Bellini-C2 PAGE: 1/4 Date: 10-Aug-06 RTB Reissue The items in bold italics have been changed. Subject: Firmware History (Bellini-C2 System) No.: RB070060 Prepared by: S.Ishizu From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Paper path Transmit/receive Retrofit information Other ( ) This is to inform you of the firmware history for the Bellini-C2 System.
Technical Bulletin Model: Bellini-C2 Date: 10-Aug-06 Version PAGE: 2/4 No.: RB70060 Symptom Corrected 3. Words missing (French/Spanish): Some words not displayed in French (missing from wording lists). 4. Slow printing speed with Standard TCP/IP port. IMPORTANT: To ensure the above symptoms do not occur, it is also necessary to update to the following firmware versions or newer: l BIOS: B0705742D: K02EL00O l NIC: B0705735B: V.4.03 l LCDC: B0705371B (NA): V.2.07 B0705372B (EU): V.2.
Technical Bulletin Model: Bellini-C2 Version Date: 10-Aug-06 PAGE: 3/4 No.: RB70060 Symptom Corrected 14. Image is not printed out correctly if Interrupt Copy is used while printing out a Document Server file. C D E B0705774 Specification change: Estimated job completion times added to New Job table for the Printer function. 1. Modified for use with the EB-105EX controller (EFI). 2. Error in storing debug log data when the function is set for engine log storage (2224) of paper jams. 1.
Technical Bulletin Model: Bellini-C2 Version No.: RB70060 Symptom Corrected 5. 6. A Date: 10-Aug-06 PAGE: 4/4 1. 2. 3. 4. 5. used without performing SP5832-001 (HDD Initialization). SC819 sometimes occurs when a defective HDD sector is detected. SC818 sometimes occurs when a relatively large print job is sent via a USB connection. The pre-set (new) job sometimes does not start when the Reverse Job Setting is set to “Previous Job.” (Note: This setting is in Copier/Document Server Features in UP mode).
Technical Bulletin Model: Bellini-C2 Date: 6-Sep-06 Subject: Waste Toner Clogging PAGE: 1/2 No.: RB070061 Prepared by: M.Matsuda From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Paper path Transmit/receive Retrofit information Other ( ) Important Notes on Preventing Waste Toner Clogging 1.
Technical Bulletin Model: Bellini-C2 Date: 6-Sep-06 PAGE: 2/2 No.: RB070061 2. If you replace the toner transport coil (P/N A2943619), make sure to install the new coil and upper case (P/N B0703636; #41 below) together as a set. Note: To ensure that the gears engage correctly, a spacer was added to the right edge of the coil from February 2004 production. There was no service P/N change, but all coils in stock at SPC are the new ones.
Technical Bulletin Model: Bellini-C2 PAGE: 1/3 Date: 28-Dec-06 No.: RB070062 Subject: Patch Release for EB-105EX V.1.2 (Composite01) Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Paper path Electrical Transmit/receive Service manual revision Retrofit information Other ( ) This RTB is the release note for Composite Patch for EB-105EX printer controller System V1.2. 1.
Technical Bulletin Model: Bellini-C2 Date: 28-Dec-06 PAGE: 2/3 No.: RB070062 1-IP6WX SC955 happens during jam recovery (Jam Code 011 and 013) 1-JRSHP With a Full Bleed size job with Acrobat, the Z-folding setting will be released. 1-HQ1NJ While printing an extremely large file, when cancelling the current job and then cancelling the waiting jobs, the controller may freeze. 1-JWQIP When send a data that has page overlay, some areas will be not printed.
Technical Bulletin Model: Bellini-C2 Date: 28-Dec-06 PAGE: 3/3 No.: RB070062 Read carefully the installation instructions for each patch as written below: ================================================================================ 1-HASH8 (A patch which will update the FPGA revision to Rev.20) Printing out the configuration sheet of EB-105EX can check the FPGA revision number.
Technical Bulletin Model: Bellini-C2 PAGE: 1/2 Date: 28-Dec-06 Subject: Patch Release for EB-105EX V.1.2 (1-N522T) No.: RB070063 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Paper path Electrical Transmit/receive Service manual revision Retrofit information Other ( ) This RTB is the release note for Patch File 1-N522T for EB-105EX printer controller System V1.2.
Technical Bulletin Model: Bellini-C2 Date: 28-Dec-06 PAGE: 2/2 No.: RB070063 9. Print out the Configuration Sheet. 10. Make sure that patch number 1-N522T is listed in the “Update Information” section of the Configuration Sheet.
Technical Bulletin Model: Bellini-C2 PAGE: 1/2 Date: 28-Dec-06 Subject: Patch Release for EB-105EX V.1.2 (1-OT69U) No.: RB070064 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Paper path Electrical Transmit/receive Service manual revision Retrofit information Other ( ) This RTB is the release note for Patch File 1-OT69U for EB-105EX printer controller System V1.2.
Technical Bulletin Model: Bellini-C2 Date: 28-Dec-06 PAGE: 2/2 No.: RB070064 8. Wait until “EB-105EX” is displayed on the EB-105EX LCD panel. 9. Print out the Configuration Sheet. 10. Make sure that patch number 1-OT69U is listed in the “Update Information” section of the Configuration Sheet.
Technical Bulletin Model: Bellini-C2 PAGE: 1/2 Date: 28-Dec-06 Subject: Patch Release for EB-105EX V.1.2 (1-MMWR9) No.: RB070065 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Paper path Electrical Transmit/receive Service manual revision Retrofit information Other ( ) This RTB is the release note for Patch File 1-MMWR9 for EB-105EX printer controller System V1.2.
Technical Bulletin Model: Bellini-C2 l Date: 28-Dec-06 PAGE: 2/2 No.: RB070065 “Fiery” menu à “Shut Down” à “Reboot System” 6. Wait until “EB-105EX” is displayed on the EB-105EX LCD panel. 7. Reboot the EB-105EX again. Note: This step is necessary to apply the new patch. 8. Wait until “EB-105EX” is displayed on the EB-105EX LCD panel. 9. Print out the Configuration Sheet. 10. Make sure that patch number 1-MMWR9 is listed in the “Update Information” section of the Configuration Sheet.
Technical Bulletin Model: Bellini-C2 PAGE: 1/2 Date: 10-Apr-07 Subject: Patch Release for EB-105EX V.1.2 (1-Q3WG8) No.: RB070067 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Paper path Transmit/receive Retrofit information Other ( ) This RTB is the release note for Patch File 1-Q3WG8 for EB-105EX printer controller System V1.2.
Technical Bulletin Model: Bellini-C2 Date: 10-Apr-07 PAGE: 2/2 No.: RB070067 7. Print out the Configuration Sheet. 8. Make sure that patch number 1-Q3WG8 is listed in the “Update Information” section of the Configuration Sheet.
Technical Bulletin Model: Bellini-C2 PAGE: 1/2 Date: 10-Apr-07 Subject: Patch Release for EB-105EX V.1.2 (1-PH0HL) No.: RB070068 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Paper path Transmit/receive Retrofit information Other ( ) This RTB is the release note for Patch File 1-PY0HL for EB-105EX printer controller System V1.2.
Technical Bulletin Model: Bellini-C2 Date: 10-Apr-07 PAGE: 2/2 No.: RB070068 8. Make sure that patch number 1-PY0HL is listed in the “Update Information” section of the Configuration Sheet.
Technical Bulletin Model: Bellini-C2 PAGE: 1/2 Date: 10-Apr-07 Subject: Patch Release for EB-105EX V.1.2 (1-QF3AI) No.: RB070069 Prepared by: Chisato Tsuji From: 2nd Tech Support Sec. Service Support Dept. Classification: Troubleshooting Part information Action required Mechanical Electrical Service manual revision Paper path Transmit/receive Retrofit information Other ( ) This RTB is the release note for Patch File 1-QF3AI.ps for EB-105EX printer controller System V1.2.
Technical Bulletin Model: Bellini-C2 Date: 10-Apr-07 PAGE: 2/2 No.: RB070069 8. Make sure that patch number 1-QF3AI is listed in the “Update Information” section of the Configuration Sheet.
