User Guide Savi Mobile Reader SMR-650 for the Intermec 751G/A Mobile Computer and PC Version 1.
Published August 2005 Part number 805-04750-001 Rev A Documentation for Savi Mobile Reader SMR-650 for the Intermec 751G/A Mobile Computer and PC, version 1.0 Copyright © 2005 Savi Technology, Inc. All rights reserved. Information in this manual is subject to change without notice and does not represent a commitment from the vendor. The software and/or databases described in this document are furnished under a license agreement or nondisclosure agreement.
Contents 1 About the Savi Mobile Reader SMR-650 and Mobile Computer SMR-650 Reader Communication . . . . . . . . . . . . . . . . . . . . . . . . . 7 UHF Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 LF Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Optimizing the SMR-650-212 Reader Tag Collection Range . . . . 8 Operating the Mobile Device . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printing Labels Connecting the Printer to the Mobile Device . . . . . . . . . . . . . . . . 22 Using the Intermec Boot to Connect to the Mobile Device . . . 22 Using the Intermec Dock to Connect to the Mobile Device . . . 24 A SMR-650 Reader Specifications B Hardware Components SMR-650-212 Reader Components . . . . . . . . . . . . . . . . . . . . . . . 34 SMR-650-210 and SMR-650-213 Reader Components . . . . . . . .
CHAPTER 1 About the Savi Mobile Reader SMR-650 and Mobile Computer 1 Savi® Mobile Reader SMR-650 is a portable radio frequency identification (RFID) reader that communicates with Savi RFID tags. There are three models of the Savi Mobile Reader SMR-650: SMR-650-212 ◆ SMR-650-210 ◆ SMR-650-213 ◆ The SMR-650-212 Reader is mounted on the Intermec® 751G/A Mobile Computer and is packaged in kits that provide a specific set of components.
CHAPTER 1 About the Savi Mobile Reader SMR-650 and Mobile Computer This guide is primarily designed for use of the SMR-650-212 Reader as packaged in kit models 741G-Kit-C-101x and 751G-Kit-C-101x. It also describes reader functionality, components, and specifications. Note: In this guide, when the model of the mobile reader or kit is not specifically mentioned, the information applies to all mobile reader models and kits.
SMR-650 Reader Communication SMR-650 Reader Communication The SMR-650 Reader has an ultra high frequency (UHF) transceiver and low frequency (LF) transmitter that communicate with all Savi RFID tags via the UHF and LF antennas. Your software determines if you are using UHF or LF commands. The SMR-650-212 Reader works on a wireless or wired LAN so you can download and upload information to and from your database. UHF Mode The UHF transmitter sends commands and write information to Savi RFID tags.
CHAPTER 1 About the Savi Mobile Reader SMR-650 and Mobile Computer Figure 1-3 Reset contacts, LEDs, and pin connector (jack) for recharging for SMR-650-210 and SMR-650-213 Reset contacts, LEDs, and pin connector (jack) for SMR-650-210 and SMR-650-213 LF Mode LF mode is controlled by the software running on the mobile computer. LF mode is compatible only with SaviTags. To use LF mode, you must turn it on in your software.
Optimizing the SMR-650-212 Reader Tag Collection Range Figure 1-4 Hold the mobile device close to eye level and parallel to your body for optimal tag collection Factors that can limit the SMR-650 Reader collection range include: ◆ Obstructions such as multiple walls, chained areas, solid-core doors, and enclosures ◆ RF interference from other equipment such as computers, cellular phones, walkie-talkies, elevators, electrical motors, or other RF-emitting devices ◆ Reflection from the ground and from n
CHAPTER 1 About the Savi Mobile Reader SMR-650 and Mobile Computer Operating the Mobile Device The mobile device consists of the SMR-650-212 Reader mounted on an Intermec 751G/A Mobile Computer, which runs the Windows CE .NET 4.2 operating system and includes a 42-character alphanumeric keyboard. The Intermec 751G/A Mobile Computer features a backlight for the keypad. Note: This guide provides general information for operating the Intermec 751G/A Mobile Computer keypad.
Operating the Mobile Device Intermec 751G/A Mobile Computer Keypad Figure 1-5 shows the keypad of the Intermec 751G/A Mobile Computer. Figure 1-5 Intermec 751G/A Mobile Computer Keypad Use the Gold/White Plane key to access display controls, special characters, and Windows CE options Use the Blue Alpha Plane key to enter letters Keys Unique to the Intermec 751G/A Mobile Computer Blue Alpha Plane Key The Blue Alpha Plane key allows you to enter letters.
CHAPTER 1 About the Savi Mobile Reader SMR-650 and Mobile Computer Reset Contacts in Pinholes on the SMR-650 For the SMR-650-212 Reader, the reset contacts are located in the pinholes on the unit. For the SMR-650-210 and SMR-650-213 Readers, the reset contacts are located in the pinholes on the cable. See Figure 1-2 and Figure 1-3 for reset pinhole location.
For More Information Contacting Savi Support If you cannot find the information you need, contact Savi Support. ◆ Check www.savi.com/services/su.contact.shtml for contact information. ◆ Send email to help@savi.com. ◆ Call 1-888-994-SAVI (North America only) or 1-408-743-8888 between 9 a.m. and 5 p.m. Pacific time.
CHAPTER 14 1 About the Savi Mobile Reader SMR-650 and Mobile Computer
CHAPTER 2 Assembling and Using 2 the Intermec Holster Inserting the Mobile Device into the Holster As you follow these steps, refer to the corresponding photos on the next page. 1. Buckle the waist strap around your waist. 2. Buckle the leg strap around the middle of your thigh. 3. Adjust the waist and leg straps for a secure fit. 4. Turn the mobile device upside-down. Ensure that the unit is vertical. 5. Insert and slide the mobile device into the holster.
CHAPTER 2 Assembling and Using the Intermec Holster Figure 2-1 Inserting the mobile device into the holster For the instructions that correspond to these photos, see “Inserting the Mobile Device into the Holster” on page 15.
CHAPTER Recharging Batteries 3 3 Recharging the SMR-650-212 Reader Battery The SMR-650-212 Reader has a Lithium-Ion internal battery that is not replaceable. To recharge the SMR-650-212 Reader battery, use the power cable and power supply with the 1/8-inch (3.2 mm) jack that Savi provides. You can also use the power cable, power supply, and Intermec dock to recharge the mobile device. Recharging both units simultaneously using the Intermec dock is the preferred method. 1.
CHAPTER 3 Recharging Batteries 3. Connect the female end of the power cable to the Intermec power supply. Connect female end of the power cable to the power supply 4. Connect the other end of the power supply to the AC adapter on the dock.
Recharging the SMR-650-210 and SMR-650-213 Reader Battery 5. Insert the mobile device into the dock. The battery of the reader and mobile computer are fully charged after three to four hours. Recharging the SMR-650-210 and SMR-650-213 Reader Battery The Lithium-Ion internal battery for the SMR-650-210 and SMR-650-213 Readers is not replaceable. To recharge the battery, use the power cable and power supply with the 1/8-inch (3.2 mm) jack that Savi provides. 1.
CHAPTER 3 Recharging Batteries 3. Connect the female end of the power cable to the mobile reader power supply. Connect female end of the power cable to the power supply Connect this end of the power supply to the mobile reader 4. Connect the other end of the power supply to the mobile reader. Determining Available Battery Power You can determine the percentage of battery power available based on the activity of the green LED on the SMR-650 Reader.
CHAPTER Printing Labels 4 4 You can print labels using the serial interface cable (Zebra Pt# 52712). Before you attempt to print using the Savi Mobile Reader SMR-650, verify that the Zebra printer is in proper working order by printing a test label. See the Zebra user’s guide for instructions. This chapter applies to kits that include the portable Zebra printer, boot for the printer, and serial cable with an RJ-45 and DB-9 connector for hardware accessories.
CHAPTER 4 Printing Labels Connecting the Printer to the Mobile Device You connect the printer to the mobile device using the Intermec boot. You can also use the Intermec dock to connect to the mobile device. Using the Intermec Boot to Connect to the Mobile Device 1. Retrieve the network cable with a DB-9 and RJ-45 connector. 2. Connect the Intermec boot to the bottom of the mobile device.
Connecting the Printer to the Mobile Device 3. Connect the DB-9 connector to the bottom of the boot. 4. Insert the RJ-45 connector to the printer port. 5. Use the software on your mobile device to print labels.
CHAPTER 4 Printing Labels Using the Intermec Dock to Connect to the Mobile Device 1. Retrieve the network cable with a DB-9 and RJ-45 connector. 2. Connect the DB-9 connector to the Intermec dock.
Connecting the Printer to the Mobile Device 3. Insert the RJ-45 connector to the printer port. 4. Insert the mobile device into the dock. 5. Use the software on your mobile device to print labels.
CHAPTER 26 4 Printing Labels
APPENDIX SMR-650 Reader Specifications A A Specification Description Physical characteristics Length: 6.25 inches (15.88 cm) including antenna and cable Width: 2.5 inches (6.35 cm) Height: 1 inch (2.5 cm) Weight: 6.4 ounces (181 g) with clip Environment Storage temperature: –4°F to +140°F (–20°C to +60°C) ambient Operating temperature: –4°F to +140°F (–20°C to +60°C) ambient; 32°F to +104°F (0°C to +40°C) when charging Humidity: 5 to 95% non-condensing. IP64 compliant.
APPENDIX A SMR-650 Reader Specifications RF receiver/ transmitter Ultra High Frequency (UHF) receiver and transmitter (downlink and uplink): Frequency: 433.92 MHz Range: UHF read/write (symmetrical) range of up to 200 feet (61 m) line of site to SaviTag ST-6XX series and SaviTag ST-41X series Modulation: Frequency shift keying, deviation +/- 50 KHz Data rate: 27.
Tag compatibility SaviTag ST-6XX series and SaviTag ST-41X series Interfaces SMR-650-212: Cable with Intermec proprietary interface and overmolded connectors. Cable is approximately 5 inches (12.7 cm) in length SMR-650-210 and SMR-650-213: Cable with serial DB-9 interface. Cable for SMR-650-210 is approximately 1 foot (30.48 cm) in length. Cable for SMR-650-213 is approximately 9 feet (2.74 m) in length. RS-232 Interface Data rate: 19.
APPENDIX A SMR-650 Reader Specifications Power Primary: Rechargeable and non-replaceable Li-Ion battery (3.
Mobile computer mounting Mounting hardware and bracket attaches the SMR-650-212 Reader to the Intermec 751G/A Mobile Computer.
APPENDIX 32 A SMR-650 Reader Specifications
APPENDIX B Hardware Components B The SMR-650-212 is packaged in kits that include the following items: ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ Intermec model 751G/A handheld terminal with alpha keypad, 802.
APPENDIX B Hardware Components SMR-650-212 Reader Components Custom Intermec cable Rechargeable Lithium-Ion battery (internal and non-removable) ◆ AC adapter to recharge the mobile reader internal battery ◆ ◆ Figure B-1 SMR-650-212 Reader SMR-650-212 Reader with custom Intermec cable SMR-650-210 and SMR-650-213 Reader Components Rechargeable Lithium-Ion battery (internal and non-removable) ◆ AC adapter to recharge the mobile reader internal battery ◆ Figure B-2 SMR-650-210 and SMR-650-213 Reader SMR