Installation Instructions

ManualsBrandsSave-T Cover ManualsElectronicsTransceiver for Utility Meters

1 of 12 601311 Rel-0005CoverLink™ Wireless

CoverLink™ WIRELESS 120V 903 MHZ

INSTALLATION INSTRUCTIONS

1-800-447-2838 www.coverpools.com

This document contains individual instructions that relate to the

installation of the CoverLink Wireless 120V 903mhz:

• 600598_rel0006 - updated July 2021

• 600597_rel0006 - updated July 2021

• 600568_rel0014 - updated July 2021

• 601097_rel0007 - updated July 2021

• 601289_rel0007 - updated July 2021

The document releases here show the latest information.

Summary of content (12 pages)

PAGE 1
-800-447-2838 www.coverpools.com CoverLink™ WIRELESS 120V 903 MHZ INSTALLATION INSTRUCTIONS This document contains individual instructions that relate to the installation of the CoverLink Wireless 120V 903mhz: • 600598_rel0006 - updated July 2021 • 600597_rel0006 - updated July 2021 • 600568_rel0014 - updated July 2021 • 601097_rel0007 - updated July 2021 • 601289_rel0007 - updated July 2021 The document releases here show the latest information.
PAGE 2
1-800-447-2838 www.coverpools.com 14 pt Instructions WARNING Pre-wiring Coverlink™ Wireless Control 120v 21pt WARNING FOR YOUR SAFETY—This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed where such state or local requirements exists.
PAGE 3
Instructions CoverLink™ Wireless Control Placement & Antenna Mounting Locations For Aluminum Lid-Bench & Hydraulic Systems The antenna for the CoverLink receiver is mounted on top of the aluminum lid or outside the bench assembly. The antenna has a 10 ft. cable and can be extended out for a clear line of reception. NEVER CUT or KINK THE ANTENNA CABLE.
PAGE 4
Instructions 1-800-447-2838 www.coverpools.com CoverLink™ Wireless Control (903 MHz) Operation and Programming The CoverLink wireless control system controls access to operate the pool cover. The CoverLink wireless control uses a Personal Identification Number (PIN) instead of a key. Entering a valid PIN into the control pad allows access to cover and uncover the pool.
PAGE 5
1. NORMAL OPERATION 1.1 Normal use: Control Pad PIN entry controls access to cover and uncover the pool. After entering the PIN, press & hold C or U within 20 seconds or the system will time out and PIN re-entry will be required. 1.1.1 Enter four-digit PIN: 1583 (or valid PIN) a. The red LED will flash as each button is pressed. b. The green LED will flash if PIN is accepted. Press & Hold C (Cover) to cover or U (Uncover) to uncover the pool. PIN. c.
PAGE 6
3. DELETE PIN 3.1. Delete PIN (except master): To erase one PIN at a time from the receiver, follow this process. Buttons must be pressed within 20 seconds of each other or programming access will time out. 3.1.1. Enter 1583 (or current master PIN) a. The red LED will flash as each button is pressed. b. The green LED will flash if PIN is accepted. 3.1.2. Press 1 to enter programming mode. a. The red and green LED will be on. 3.1.3. Press 2 to enter PIN delete mode. a.
PAGE 7
Prior to programming the CoverLink™ system, complete the following steps at the auto-shutoff board and CoverLink receiver: Uncover and cover the pool completely by pushing the buttons on the CoverLink receiver located in the auto-shutoff box as shown on page 1 in illustration CoverLink receiver. If the operation of the cover is sluggish or stopping, adjust the amp limiter located on the auto-shutoff board as described in document #600356 WIRING AUTO-SHUTOFF AMP LIMIT BRD-ACCB-AMP LMT LED FUNC. 5.
PAGE 8
PROBLEM LEDs on control pad do not light when buttons are pressed. Did not fix problem. SOLUTION Remove control pad faceplate. Remove batteries from battery holder. Clean battery contacts. Install new batteries in battery holder. Reinstall control pad faceplate. Contact local cover dealer for service. PIN entry does not activate cover Enter valid PIN. mechanism, but red LED on the control If PIN is valid, Green LED will flash as C (Cover) or U (Uncover) is pad is on when buttons are pressed. pressed.
PAGE 9
Coverlink™ Wireless Control Troubleshoot Guide Qualified service personnel only Verify that the auto-shutoff board is working properly prior to troubleshooting the CoverLink system. PROBLEM Auto-shutoff Verification Cover system does not operate or operates intermittently. SOLUTION Step 1. Check for secure wiring connections at the circuit breaker, auto-shutoff board, receiver board, and motor. Check that the antenna wire is secure and not damaged. All wiring is good, go to step 2. Step 2.
PAGE 10
Coverlink™ Wireless Control Troubleshoot Guide Qualified service personnel only PROBLEM Troubleshooting CoverLink The CoverLink system does not operate or operates intermittently SOLUTION Step 1. Reboot the receiver: Turn the system power off to the receiver and auto-shutoff board, leave it off for 30 seconds, then turn the system power back on. (Skip step 1 if completed in auto-shutoff verification) Step 2. Try the receiver override buttons, Cover and Uncover. If the buttons work, go to step 4.
PAGE 11
Wiring Instructions Motor 120v Model #050239 or Model #050348 to Auto-Shutoff Amp 3 Wire Limit 120v Model #050338/050440 with Acc Board Model #050253 1-800-447-2838 www.coverpools.com AB 5V Key Switch ORANGE WHITE BLACK WHITE RED BLACK M0T0R 120V (HIGH VOLTAGE WIRES) RED WHITE or CoverLink™ Wireless NEUTRAL HOT 120 VAC 15 AMP DEDICATED G.F.C.I.
PAGE 12
AB 5V Key Switch Wiring Instructions Motor 120v Model #050239 or #050348 to 3 Wire Auto-shutoff Amp Limit 120v Model #050338/050440 with CoverLink™ Wired Control Model #050332 and Acc Board Model #050253 1-800-447-2838 www.coverpools.