sauder.com The original desktop. Desk Beginnings Collection | 415817 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-12 Français pg 13-14 Español pg 15-16 Lot # 372244 05/11/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 2 No. 2 Phillips Screwdriver Tip Shown Actual Size 3 4-12 Hammer Français 13-14 Español 15-16 Safety 17-18 Warranty å Not actual size 19 While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1F HIDDEN CAM - 2 6I STRIKE PLATE - 1 20P SCREW COVER - 14 6S 2F 9I CAM DOWEL - 2 WASHER - 1 1R 25H PIVOT HINGE- 2 45K PULL - 1 METAL PIN - 4 1N 2R RUBBER SLEEVE - 4 MAGNETIC CATCH - 1 12P CAM COVER - 2 5R SUPPORT PIN - 4 11S BLACK 1/2" FLAT HEAD SCREW - 1 BROWN 7/16" LARGE HEAD SCREW - 2 53S SILVER 3/4" MACHINE SCREW - 2 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push two HIDDEN CAMS (1F) into the DESK UPRIGHT (C2). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. C2 Arrow Arrow 1F 2F Insert the metal end of the CAM DOWEL into the HIDDEN CAM. Page 4 415817 www.sauder.
Step 2 å Using your hammer, gently tap four SUPPORT PINS (5R) into the DESK ENDS (A2 and B2). å Fasten the DESK UPRIGHT (C2) to the DESK TOP (D). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 5R If the DESK TOP has an unfinished surface, it should be positioned here. A2 Finished edge B2 D S AM C DEN HID C2 with e c fa Sur Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened.
Step 3 å Fasten the DESK BOTTOM (E) and DESK SHELF (G) to the DESK UPRIGHT (C2). Use four BLACK 1-15/16" FLAT HEAD SCREWS (113S). å Fasten the DESK RIGHT END (A2) to the DESK TOP (D), DESK BOTTOM (E), and DESK SHELF (G). Use six BLACK 1-15/16" FLAT HEAD SCREWS (113S). å Insert the MAGNETIC CATCH (2I) into the hole in the DESK SHELF (G). For door adjustment, turn the barrel counter-clockwise. Finished edge 2I D C2 Finished edge G Su witrface hh ole s A2 This hole must be here.
Step 4 å å Carefully turn your desk onto its top. Fasten the DESK MODESTY PANEL (F) to the DESK UPRIGHT (C2). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). C2 F Notch If the DESK MODESTY PANEL has an unfinished surface, it should be positioned here. 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) www.sauder.
Step 5 å Fasten the DESK LEFT END (B2) to the DESK TOP (D) and DESK MODESTY PANEL (F). Use four BLACK 1-15/16" FLAT HEAD SCREWS (113S). F D B2 Finished edge 113S BLACK 1-15/16" FLAT HEAD SCREW (4 used in this step) Page 8 415817 www.sauder.
Step 6 å Carefully turn your unit over onto its front edges. Lay the DESK BACK (H) over your unit. å Make equal margins along all four edges of the DESK BACK (H). Push on opposite corners of your unit if needed to make it “square”. å å Fasten the DESK BACK (H) to your unit using the NAILS (1N). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 7 å Fasten a PIVOT HINGE (25H) to the DESK DOOR (I). Use a BROWN 7/16" LARGE HEAD SCREW (6S). å Fasten a STRIKE PLATE (6I) to the DESK DOOR (I). Use a BLACK 1/2" FLAT HEAD SCREW (11S). å NOTE: The surface of the STRIKE PLATE with "SAUDER" should be facing up. IMPORTANT: Fasten only one PIVOT HINGE to the DESK DOOR in this step 6S BROWN 7/16" LARGE HEAD SCREW (1 used for the PIVOT HINGE) I 25H 11S BLACK 1/2" FLAT HEAD SCREW (1 used for the STRIKE PLATE) 6I Page 10 415817 www.sauder.
Step 8 å å Carefully stand your desk upright. å Insert the PIVOT HINGE, which is fastened to the DESK DOOR (I), into the hole in the DESK SHELF (G). You will need to tilt your DOOR slightly. å Now, tip the DESK DOOR (I) in and fasten the free PIVOT HINGE (25H) to the DESK DOOR. Use a BROWN 7/16" LARGE HEAD SCREW (6S). å NOTE: To make adjustments to the DESK DOOR, loosen the SCREW in the HINGE, make needed adjustments, and tighten the SCREW. å Fasten the PULL (45K) to the DESK DOOR (I).
Step 9 å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the DESK RIGHT END (A2) and DESK UPRIGHT (C2). Set the DESK ADJUSTABLE SHELF (J) onto the METAL PINS. å Center a SCREW COVER (20P) over the head of each visible SCREW and press firmly. å Push a CAM COVER (12P) onto each HIDDEN CAM in the DESK UPRIGHT (C2). å NOTE: Please read the back pages of the instruction booklet for important safety information.
415817 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 (SUITE) Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer l'ARRIÈRE DE BUREAU (H) à l'élément à l'aide des CLOUS (1N). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. REMARQUE : S'assurer de bien enfoncer les CLOUS dans les trous qui sont alignés au-dessus la TABLETTE DE BUREAU (G). Enfoncer deux EXCENTRIQUES ESCAMOTABLES (1F) dans le MONTANT DE BUREAU (C2).
415817 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 (CONTINUACIÓN) No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Los márgenes a lo largo de todos los bordes del DORSO DEL ESCRITORIO (H) deben estar uniformes. Empuje sobre las esquinas opuestas de la unidad si es requerido para hacerla "cuadrada." Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje dos EXCÉNTRICOS ESCONDIDOS (1F) dentro del PARAL DEL ESCRITORIO (C2).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes y cajones sobrecargados • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
