413034 Multimedia Storage Tower PLEASE CONTACT US BEFORE RETURNING YOUR UNIT TO THE STORE 1-800-523-3987 www.sauder.com NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English ...................... Page 1-9 Français ...............Pages 10-11 Made in the USA Archbold, OH Espanol.............
TABLE OF CONTENTS ASSEMBLY TOOLS REQUIRED Part Identification .......................3 Hardware Identification .............4 No. 2 Phillips Screwdriver Assembly Steps ...................... 5-9 Tip Shown Actual Size Français .............................. 10-11 Espanol............................... 12-13 Hammer Safety .......................................14 Warranty ...................................15 Page 2 www.sauder.
PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help identify similar parts. A RIGHT END 2 B LEFT END 2 C TOP 1 D BOTTOM 1 E SHELF 1 F ADJUSTABLE SHELF 4 G BACK 2 C G A F F E G A B F F B D 413034 www.sauder.
HARDWARE IDENTIFICATION 1F HIDDEN CAM - 4 2F CAM DOWEL - 4 J SAFETY BRACKET - 1 K FOOT - 5 L CAM COVER - 4 M METAL PIN - 20 N RUBBER SLEEVE - 16 O BLACK 1-7/8" FLAT HEAD SCREW - 9 P BLACK 9/16" PAN HEAD SCREW - 5 Q BLACK 9/16" LARGE HEAD SCREW - 1 R NAIL - 42 Screws are shown actual size. You may receive extra hardware with your unit. Page 4 www.sauder.
S p te Look for this icon. It means a video assembly tip is available at: www.sauder.com/services/tips 1 Do not tighten the HIDDEN CAMS in this step. B B A A Arrow Arrow 1F (4 used) 2F Insert the metal end of the CAM DOWEL into the HIDDEN CAM. Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Push four HIDDEN CAMS (1F) into the ENDS (A and B). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. 413034 www.sauder.
S p te 2 M Curved edge Finished edge C B Finished edge E Sur f mo ace w re h ith ole s A M O BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) Push two METAL PINS (M) into the top edge of the ENDS (A and B). Fasten the ENDS (A and B) to the TOP (C). Tighten two HIDDEN CAMS. NOTE: Be sure the METAL PINS in the ENDS insert into the holes in the TOP. Fasten the SHELF (E) to the ENDS (A and B). Use four BLACK 1-7/8" FLAT HEAD SCREWS (O). Caution Risk of damage or injury.
S p te 3 M Finished edge E Curved edge B Finished edge D Sur f mo ace w re h ith ole s A M Maximum 210 degrees Arrow Minimum 190 degrees O BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) Push two METAL PINS (M) into the top edge of the remaining ENDS (A and B). Fasten the ENDS (A and B) to the SHELF (E). Tighten two HIDDEN CAMS. NOTE: Be sure the METAL PINS in the ENDS insert into the holes in the SHELF. Fasten the BOTTOM (D) to the ENDS (A and B).
S p te Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 4 1-1/2” 5" R NAIL (42 used in this step) Overlap the BACKS and nail them to the SHELF (E). 1/4” G n U fi ed sh ni G n U fi ed sh ni D For support, place packing foam and magazines here. P K BLACK 9/16" PAN HEAD SCREW (5 used for the FEET) Carefully turn your unit over onto its front edges. Unfold the BACKS (G) and lay them over your unit.
S BLACK 1-7/8” FLAT HEAD SCREW (1 used into a stud in your wall) p te 5 O J BLACK 9/16” LARGE HEAD SCREW (1 used into the top of your unit) Q 5 lbs. B F 7 lbs. F 7 lbs. A 15 lbs. B F 7 lbs. F 7 lbs. A 30 lbs. M (16 used) N L (4 used) To cover HIDDEN CAMS Carefully stand your unit upright. Push the RUBBER SLEEVES (N) over the remaining METAL PINS (M). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B). Set the ADJUSTABLE SHELVES (F) onto the METAL PINS.
Tour de Rangement Multimédia 413034 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 4 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Attention Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer quatre EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B). Ensuite, insérer l’extrémité en metal de la CHEVILLE D'EXCENTRIQUE (2F) dans chaque EXCENTRIQUE ESCAMOTABLE.
413034 Torre de Almacenamiento Multimedia Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 4 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Precaución No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje cuatro EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B). A continuación, inserte el extremo de metal de un PASADOR DE EXCÉNTRICO (2F) dentro de cada EXCÉNTRICO ESCONDIDO.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves. Place the heavier items on the lower shelves.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear valued customer: Thank you for your purchase from the Sauder family companies. It’s our pleasure to provide you with an affordable solution that meets your furniture and storage needs. I hope you will enjoy it for years to come. I am pleased with this company’s consistent ability to amaze the customer over time. My grandfather, Erie Sauder, founded the company in 1934 and later invented and patented the first commercially successful ready-to-assemble table.
