sauder.com Deep shelves for tall tales. 5-Shelf Bookcase 409090 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-11 Français pg 12-13 Español pg 14-16 Lot # 372070 05/06/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 2-3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-11 Hammer Français 12-13 Español 14-16 Safety 17-18 Warranty Page 2 Not actual size Skip the power trip. This time. 19 409090 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. A4 UPPER END (2) B TOP/BOTTOM (2) CC D LOWER RIGHT END (1) ADJUSTABLE SHELF (3) EE2 LOWER LEFT END (1) F2 FIXED SHELF (1) G BACK (2) G B A4 D A4 D F2 CC D G EE2 B www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. H2 I2 HIDDEN CAM - 2 K L SAFETY BRACKET - 1 M RUBBER SLEEVE - 12 113S CAM COVER - 2 METAL PIN - 14 N APPLIQUE CARD - 1 BLACK 1-15/16" FLAT HEAD SCREW - 10 Q BLACK 9/16" LARGE HEAD SCREW - 1 Page 4 J CAM DOWEL - 2 409090 P BLACK 1-7/8" FLAT HEAD SCREW - 1 R NAIL - 48 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Push two HIDDEN CAMS (H2) into the LOWER ENDS (CC and EE2). Then, insert the metal end of a CAM DOWEL (I2) into each HIDDEN CAM. Scan this QR code or go to this address: http://qr.sauder.com/?ID=1095 to watch a video on how to assemble your unit. Do not tighten the HIDDEN CAMS in this step.
Step 2 å å Fasten the UPPER ENDS (A4) to one of the TOP/ BOTTOMS (B). Use four BLACK 1-15/16" FLAT HEAD SCREWS (113S). Remember: Righty tighty. Lefty loosey. Fasten the FIXED SHELF (F2) to the UPPER ENDS (A4). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 3 å å Insert two METAL PINS (L) into the LOWER ENDS (CC and EE2). å NOTE: Be sure the METAL PINS in the LOWER ENDS insert into the holes in the FIXED SHELF. å Fasten the remaining TOP/BOTTOM (B) to the LOWER ENDS (CC and EE2). Use four BLACK 1-15/16" FLAT HEAD SCREWS (113S). Fasten the LOWER ENDS (CC and EE2) to the FIXED SHELF (F2). Tighten two HIDDEN CAMS.
11/16" Step 4 å å Position one of the BACKS (G) over the upper portion of your unit. å Fasten this BACK (G) to the upper portion of your unit using the NAILS (R). The NAILS should be approximately 5" apart, 1-1/2" from the corners, and 1/4" in from the edges. å NOTE: Do not tap nails into the bottom edge of this BACK at this time. å Fasten the remaining BACK (G) to the lower portion of your unit using the NAILS (R).
Step 5 å å Carefully stand your unit upright. Pro Tip: Lift with your legs. And, you know, your arms. Push the RUBBER SLEEVES (M) over the METAL PINS (L). Insert the METAL PINS into the hole locations of your choice in the ENDS (A4, CC, and EE2). Set the ADJUSTABLE SHELVES (D) onto the METAL PINS. D A4 D A4 EE2 D CC L (12 used) www.sauder.
Step 6 å å Push a CAM COVER (J) onto each HIDDEN CAM. Peel the APPLIQUES from the APPLIQUE CARD (N). Stick the APPLIQUES over the SCREW heads in the ENDS (A4, CC, and EE2). A4 A4 EE2 J CC (2 used) N To cover HIDDEN CAMS (8 used) Page 10 409090 www.sauder.
Step 7 å We recommend using the SAFETY BRACKET (K) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (Q) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (P) into a stud in your wall. å å NOTE: Please read the back page of the instruction booklet for important safety information. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
409090 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 4 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES à cette étape. Attention: Ne pas relever l’élément dans sa position verticale avant d’avoir fixé l’ARRIÈRES. L’élément risque de s’effondrer. Assembler l’élément sur un sol à moquette ou sur le carton vide pour éviter d’endommager l’élément ou le sol. Positionner l’un des ARRIÈRES (G) sur la portion supérieure de l’unité. Enfoncer deux EXCENTRIQUES ESCAMOTABLES (H2) dans les EXTRÉMITÉS INFÉRIEURES (CC et EE2).
409090 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 3 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Inserte dos ESPIGAS DE METAL (L) dentro de los EXTREMOS INFERIORES (CC y EE2). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje dos EXCÉNTRICOS ESCONDIDOS (H2) dentro de los EXTREMOS INFERIORES (CC y EE2). A continuación, introduzca el extremo en metal de un PASADOR DE EXCÉNTRICO (I2) dentro de cada EXCÉNTRICO ESCONDIDO.
PASO 4 PASO 5 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSOS. La unidad podría caerse. Cuidadosamente ponga la unidad en posición vertical. Coloque uno de los DORSOS (G) sobre la sección superior de su unidad. Fije el DORSO (G) de manera que los márgenes son iguales a lo largo de los cuatro bordes. Empuje sobre las esquinas opuestas de la unidad si es requerido para hacerla "cuadrada". Empuje los MANGUITOS DE GOMA (M) sobre las ESPIGAS DE METAL (L).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados • Cargar el producto inadecuadamente puede causar la inestabilidad. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Estantes sobrecargados pueden romper.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
