User's Manual

2
PRODUCT WARRANTY
EQUIPMENT
Saris Cycling Group warrants your product to be free of any defects in material or workmanship for 1 year. This warranty does not apply to parts that have been worn out through normal use or damaged through misuse,
abuse, neglect, accident, or unauthorized modication. Where applicable, incidental and consequential damages are not covered, and there are no other warranties, expressed or implied. This warranty applies to the original
owner only. Retain your receipt as proof of purchase.
Repair or replacement of a defective Saris product or refund of the purchase price, shall be the sole remedy of the buyer under this warranty, and in no event shall Saris Cycling Group be liable for incidental or consequential
damages, losses or expenses. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and , if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more the
following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
corrected. Consult the dealer or experience radio / TV technician for help
FCC STATEMENT
FCC ID: T8P-RFID1
MADE IN USA
This device complies with part 15 of FCC Rules. Operation is subjected to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
NOTE: The manufacturer is not responsible for any radio or TB inference caused by unauthorized
modications to this equipment. Such modications could void the user authority to operate the equipment.
CANADA STATEMENT
Copyright 2012. All rights reserved. No part of this publication may be copied, photographed, reproduced, translated, transmitted electronically or placed on digital media without the prior written consent of Saris Cycling
Group, Inc. Saris Cycling Group, Inc. , The Hub and The Hub logo, are all registered trademarks of Saris Cycling Group, Inc. All other product, brand, or trade names used in this manual may be trademarks or registered
trademarks of their respective owners. Saris Cycling Group, Inc. reserves the right to make improvements and/or updates to the products described herein at any time without notice.
COPYRIGHT, TRADEMARKS, MODIFICATIONS
2.1 CONNECT
The Hub
Designed in Madison, WI
Made in the USA
Saris Cycling Group, Inc.
Model #: NFC RFID1
FCC ID: T8P-RFID1
IC: 6459A-RFID1
Service 2Service 1
Power Outlet Ethernet Port
Plug data cable in to bottom of box and connect
to hard-wired Ethernet connection. Use a shielded
Ethernet cable. Plug cord in to bottom of box,
and connect to electrical box. Add the supplied
ferrite clamps to the end of the network cable.
The clamp must be 3-4” from the box. A successful
install of the box will result in the lights on the top
of the box ashing as it boots. System boot takes
approximately 45 seconds. At the conclusion of
the system boot, the green power light will
remain on and no other lights will be illuminated.
HUB
THE
Booting
Mode
HUB
THE
Operational
Mode
3.2 REGISTER YOUR DEVICE
1. Scan a tag on the device at least once.
2. Verify that the Network light turns o and the green light ashes twice.
For best performance, you should set a static IP address on the scanner.
Alternatively, you can add the MAC address of the scanner to any rewall or
network ltering system you have. By default, The Hub will connect to your
Network with DHCP.
1. Log in to http://thehub.saris.com
2. On the left-side of the page, under your organization, click the Flag Icon(s)
3. Select a device
4. Click Network Conguration
5. Enter the static IP address conguration
6. Click Next >>
7. Click the download link. Save the le to a ash drive
8. Unplug the power from The Hub
9. Insert the ash drive into the Service 2 Port on the bottom of The Hub
10. Re-connect the power to The Hub
11. Wait 1-2 minutes for the hub to boot and acquire the network
3.1 SET YOUR STATIC IP ADDRESS
COMPANY NAME
Saris Cycling Group, Inc. 5253 Verona Road Madison WI 53711 Ph: 800.783.7257 Fx: 608.274.1702 www.saris.com
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This Class B digitial apparatus
complies with Canadian ICES-003.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but
de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication satisfaisante. Cet appareil numérique de la classe B est conforme à la norme NMB-oo3 du Canada.