SAL-2 Series Wireless Clock Installation Manual (V1) Table of Contents MOUNTING Wall Mount Installation………………………………………………………………… Page 2 Double Mount Installation……………………………………………………………… Page 3 WIRING INFORMATION Wiring Information……………………………………………………………………...
SAL-2 Series Wireless Clock Installation Manual (V1) Wall Mount Installation 24 Volt/110 volt options shown in diagrams 12” CLOCK STANDARD SINGLE GANG BOX PLUG CONNECTOR INTO BOTTOM OF MOVEMENT 16” CLOCK STANDARD SINGLE GANG BOX PLUG CONNECTOR INTO BOTTOM OF MOVEMENT INSTRUCTIONS 1. Connect the wiring as shown on the wiring diagram (110V or 24V ONLY). 2. Mount both plastic anchors in the wall. 3. Insert the sheet metal screws (#10) through the mounting bracket into the plastic anchors. 4.
SAL-2 Series Wireless Clock Installation Manual (V1) Double Mount Installation INSTRUCTIONS 1. Screw the mounting bracket to the double gang box using four (4) inner holes on mounting bracket, or mount the mounting bracket directly to the wall or ceiling using the four (4) outer holes. 2. Insert the wires through the mounting bracket (110V or 24V ONLY). 3. Fish the wires through the clock hanging rod. 4. Secure hanging rod to mounting bracket with screws supplied, and place cover over connection. 5.
SAL-2 Series Wireless Clock Installation Manual (V1) Wiring Information Sapling WIRELESS “WHERE TIMING AND TECHNOLOGY MEET” FCC ID R73AMR001 Diagnostic Switch Diagnostic LED Transmit/Receive The Sapling SAL-2 Series clock can be powered by 2 “D” cell batteries, 24 volts AC, or 110 volts AC. Page 4 Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: (215) 322-6063 Fax: (215) 322-8498 www.Sapling-Inc.
SAL-2 Series Wireless Clock Installation Manual (V1) Operational Instructions IMPORTANT: We highly recommend installing the main transceiver before the installation of the SAL Series clocks. In order to install the clock, simply remove the battery cover, and install two (2) D cell batteries (recommended battery type: Duracell PROCELL; can be purchased through Sapling (Part # EDBATT)). After installation of the battery, replace the battery cover and the clock should start correcting within five (5) minutes.
SAL-2 Series Wireless Clock Installation Manual (V1) Operational Instructions Installation Option #1 There is a main high powered transceiver in the building and high powered transceivers or repeaters as needed to cover the entire premise. In this option, the system does not depend on the clock for transmission. OPTION 1A: Transceivers or repeaters are synchronized wirelessly to the main transceiver. 1. Place the main transceiver in a central location (hallway recommended). 2.
SAL-2 Series Wireless Clock Installation Manual (V1) Operational Instructions Installation Option #2 (continued) There is another manual option, by pressing the Transmit/Receive switch once, to enable the clock transceiver for ten (10) minutes in order to transmit the time signal. The transceiver can be enabled only if the clock receives a time signal within the last twelve (12) hours.
SAL-2 Series Wireless Clock Installation Manual (V1) Operational Instructions Installation Option #3 There is at least one (1) high powered transceiver in the building in order to cover the entire premises. The power (24V or 110V) operated clocks are used as transceivers/repeaters. Clock Operational Overview (Power Operation 24V or 110V Version) The clock enables its receiver for ten (10) minutes upon power up and during normal operation every minute.
SAL-2 Series Wireless Clock Installation Manual (V1) Frequently Asked Questions What battery size do I use for the wireless clock? The batteries required are two (2) “D” cell battery. The recommended battery type is “Duracell: Procell [D] size”. Will the clock cause interference with any of my other wireless devices? No, the SAL Series wireless clock works on 915 - 928 MHz frequency-hopping technology.
SAL-2 Series Wireless Clock Installation Manual (V1) Troubleshooting What happens if I power up the clock and the clock is not moving? The clock should move at normal speed upon power up. If it does not move at normal speed, check the battery and make sure the clock receives power. Also, be sure to remove the pin prior to starting up the clock. If the clocks are 24 volt or 110 volt, please verify the wiring on page 4 of this manual.
SAL-2 Series Wireless Clock Installation Manual (V1) Diagnostic Testing Overview The number of times that the switch is pressed will determine the diagnostic mode. After determining the diagnostic mode, the LED between the two (2) switches will start flashing a green light. The number of flashes will display the diagnostic number. DIAGNOSTIC #1 This diagnostic will determine how long (# of hours) since the clock last received the communication signal.
SAL-2 Series Wireless Clock Installation Manual (V1) Diagnostic Testing DIAGNOSTIC #2 This diagnostic will determine the quality of the time signal. In order to enter Diagnostic #2 mode, push the Diagnostic Switch twice which is indicated by the green LED flashing twice with a three (3) second break. A. While in diagnostic modes, hour and minute hands continue to run normally. B. The second hand will display the quality of the time signal. (The signal percentage is displayed on the dial of the clock.
SAL-2 Series Wireless Clock Installation Manual (V1) Diagnostic Testing DIAGNOSTIC #4 This diagnostic will test the battery level of the clock. In order to enter Diagnostic #4 mode, push the Diagnostic Switch four (4) times which is indicated by the LED flashing four times every three seconds. The second hand will display the battery level by stopping one of the numbers on the clock’s face. For example: • • • • • If the second hand lands on 2, the battery level 2.2V.
SAL-2 Series Wireless Clock Installation Manual (V1) FCC Wants You to Know This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.
