Installation Manual V8.6 SBL /SBLG Series Wireless Clock Current as of Feb. 2020 The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Important Safety Instructions ! DANGER , SHOCK HAZARD • • Keep the electricity to this device turned OFF until the clock installation is complete. Do not expose the clock movement to water, or install the clock in a location where it may be exposed to water. ! WARNING H FIRE HAZARD • Always follow your national and regional electrical codes or ordinances.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Wireless System Setup VERY IMPORTANT: INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Wireless System Setup (ctd.) System Option 1 No clocks are being used for transmission. This option should only be taken if the user already has a main high-powered transceiver and as many repeaters as needed to cover the premises. 1. Place the main transceiver in a central location, like a hallway, where the signal will not be blocked. 2.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Wall Mount Installation VERY IMPORTANT: INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Wall Mount Installation 1 2 1) If you are installing a new gang box in the wall, leave at least 4 inches between the top of the gang box and ceiling. Confirm that the bottom of the gang box is level with the floor. If you are using an existing gang box, the top of the gang box must be a minimum of three inches away from the ceiling.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Wall Mount Installation 5A 5B 5C 5D 5A) If you do not wish to attach the housing to a gang box, place the mounting piece on the wall. Leave at least 4 inches between the top rear edge of the housing and ceiling. Confirm that the bottom of the mounting piece is level with the floor. 5B) Identify the keyholes towards the top of the back of the clock housing.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com 5E 5F 5G 6 Wall Mount Installation 5E) Use a pencil to trace the holes beneath each keyhole onto the wall. Take the clock housing off the wall, drill holes at the marked locations, and add another two wall anchors. 5F) Repeat step 5D, then pass another pair of #8 screws through the bottom holes and secure them in the remaining two wall anchors.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com 7 8 9 10 Wall Mount Installation 7) Detach the filter from the clock display board by pressing inward on the red tabs. 8) Attach the power wires to the ports as shown below.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Wall Mount Installation 11 12 13 14 11) Remove the plastic cover from the display board. 12) Place the filter over the display board. You should hear a snapping noise as the latches drop into place. 13) Place the housing frame onto the housing. You should hear a snapping noise as the latches drop into place. 14) Power the clock.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Flag Mount Installation VERY IMPORTANT: INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Flag Mount Installation M3.5-1.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Flag Mount Installation 1 2 1) Install the double gang box in the wall or ceiling. If you are installing the gang box in the wall, leave at least eleven inches between the top of the gang box and the ceiling. If you are installing the gang box in the ceiling, leave at least eleven inches between the gang box and the wall.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Flag Mount Installation Steps 5 and 6 only apply to metal mounting poles. If you have an ABS mounting pole, skip to step 7 5) Remove the mounting pole end cap and the plastic ring from one of the holes. 5 6 6) Attach the flag-mount end cap to the pole. Confirm that the covering flap is attached to the side where the plastic ring was removed.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Flag Mount Installation 7 8 7) Remove the mounting plate and drill the four holes that were just traced. Insert the four wall anchors into the holes. 8) Reattach the mounting plate, this time using all four long, silver #6-32x1 screws, then insert the four #8 screws through the mounting plate and into the anchors.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Flag Mount Installation 11 12 13 14 11) Detach the frame from the front of the clock housing by pulling the bottom and top edges away from the housing. 12) Insert the four #8-32x7/16 screws through the internal-tooth washers, then through the adapter, and finally into the pole. Use a screwdriver to tighten the screws so that the adapter does not move.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com 15 16 Flag Mount Installation 15) Attach the power wires to the ports as shown below. 16) Use the M3/5-15x12 screws to attach the display board to the housing. NOTE: For 2.5” Digit clocks, the holes for the screws will be on the left and right inner surfaces of the housing. For 4.0” Digit Clocks, the holes will be on the top and bottom surfaces.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Flag Mount Installation 19 20 21 19) Place the filter over the display board. You should hear a snapping noise as the latches drop into place. 20) Place the housing frame onto the housing. You should hear a snapping noise as the latches drop into place.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Double Mount Installation VERY IMPORTANT: INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Double Mount Installation M3.5-1.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Double Mount Installation 1 2 1) Install the double gang box in the wall or ceiling. If you are installing the gang box in the wall, leave at least eleven inches between the top of the gang box and the ceiling. If you are installing the gang box in the ceiling, leave at least eleven inches between the gang box and the wall.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Double Mount Installation 5 6 7 8 5) Remove the mounting plate and drill the four holes that were just traced. Insert the four wall anchors into the holes. 6) Reattach the mounting plate, this time using all four long, silver #6-32x1 screws, then insert the four #8 screws through the mounting plate and into the anchors.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Double Mount Installation 9 10 11 12 13 9) Detach the frame from the front of each clock housing by pulling the bottom and top edges away from the housing. 10) Insert the four #8-32x7/16 screws through the internal-tooth washers, then through each adapter, and finally into the pole. Use a screwdriver to tighten the screws so that the adapters do not move.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com 14 15 Double Mount Installation 15) Use the M3/5-15x12 screws to attach each display board to the housing. 14) Attach the power wires to the port as shown below. NOTE: For 2.5” Digit clocks, the holes for the screws will be on the left and right inner surfaces of the housing. For 4.0” Digit Clocks, the holes will be on the top and bottom surfaces.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com 18 19 20 Double Mount Installation 18) Place a filter over each display board. You should hear a snapping noise as the latches drop into place. 19) Place a housing frame onto each housing. You should hear a snapping noise as the latches drop into place.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Adjustable Jumper Settings Every version of the digital clock contains a set of jumpers which can be moved to change a particular setting.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Temperature Sensor Installation (3200/3300 Only) (IMPORTANT: Detach clock from power source before installing new circuitry.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Buzzer Installation (3300 Only) (IMPORTANT: Detach clock from power source before installing new circuitry. DO NOT add new circuitry while the clock is operating) During installation, there are two port blocks mentioned. The block on the upper-left will be called J1, while the block on the bottom left will be called J3. Refer to the diagram for details.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Alternative Inputs - Clock-Side - Sync-Wire (3300 Only) In instances where a 3300 wireless digital clock is being integrated with an existing clock system, or instances where the clock is installed beyond the signal range of other wireless time transmitters, it is possible to configure the clock to accept time data from a traditional sync-wire system.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Alternative Inputs - Clock-Side - Sync-Wire 58 Minute Correction J1- 1 2 3 4 5 6 7 8 9 J1- J1- 1 2 3 4 5 6 7 8 9 Neutral Neutral Reset Reset 1 2 3 4 5 6 7 8 9 J2- 1 2 Relay N.O. COM 110VAC or 230VAC Interface 24VAC Interface Dry Contact Closure Description: 110VAC or 230VAC or 24VAC 60 Hz is used to run the clock normally.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Alternative Inputs - Clock-Side - Sync-Wire National Time/Rauland J1- 1 2 3 4 5 6 7 8 9 J1- J1- 1 2 3 4 5 6 7 8 9 Neutral Neutral Reset Reset 1 2 3 4 5 6 7 8 9 J2- 1 2 Relay N.O. COM 110VAC or 230VAC Interface 24VAC Interface Dry Contact Closure Description: National Time/Rauland - 110VAC or 230VAC or 24VAC 60 Hz is used to run the clock normally.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Alternative Inputs - Clock-Side - Sync-Wire Dukane J1- 1 2 3 4 5 6 7 8 9 J2- 1 2 Reset Minute Pulse Ground Description: Dukane - Applying a 4-10 millisecond pulse on the minute line will increment the clock in one minute. Applying a 12-50 millisecond pulse on the reset line will bring the clock back to 12:00 a.m.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Alternative Inputs - Clock-Side - RS485 (3200/3300 Only) RS485 In instances where a 3200 or 3300 wireless digital clock is being integrated with an existing clock system, or instances where the clock is installed beyond the signal range of other wireless time transmitters, it is possible to configure the clock to accept time data from a wired RS485 system.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Outputs (3300 Only) RS485 and 2-Wire Digital - Master Mode During a loss of communication with the Master Clock, the 3300 digital clock can act as a temporary, backup master clock for other clocks in the system. The port block on the bottom left side of the circuit board will be called J7. Refer to the diagram for details.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Manual Controls (3300 Only) The purpose of this section is to get a new digital clock up and running using the manual controls on the front of the digital clock. If you would prefer to program the master clock through the convenience of a graphic interface, go to the section labeled “sbdconfig - Setting up sbdconfig.exe” for an alternate programming method.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Manual Controls The numbers shown on the left are examples. Going down the list and entering every one of the examples exactly as shown will cause the clock to malfunction or use incorrect data. Program your clock setting based off of the instructions in the description on the right.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Manual Controls The numbers shown on the left are examples. Going down the list and entering every one of the examples exactly as shown will cause the clock to malfunction or use incorrect data. Program your clock setting based off of the instructions in the description on the right. 9-- 1 Setting 9 - Clock I.D.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Manual Controls The numbers shown on the left are examples. Going down the list and entering every one of the examples exactly as shown will cause the clock to malfunction or use incorrect data. Program your clock setting based off of the instructions in the description on the right.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Manual Controls The numbers shown on the left are examples. Going down the list and entering every one of the examples exactly as shown will cause the clock to malfunction or use incorrect data. Program your clock setting based off of the instructions in the description on the right.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Manual Controls The numbers shown on the left are examples. Going down the list and entering every one of the examples exactly as shown will cause the clock to malfunction or use incorrect data. Program your clock setting based off of the instructions in the description on the right.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Manual Controls The numbers shown on the left are examples. Going down the list and entering every one of the examples exactly as shown will cause the clock to malfunction or use incorrect data. Program your clock setting based off of the instructions in the description on the right.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Connecting to the Clock The USB to RS485 converter cable has two ends. One end is a USB-A adapter and will work with any USB-A port. USB-A is a rectangular-shaped port and is included on most desktop and laptop computers produced since 2000.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Setting up sbdconfig.exe Please Note: • • The sbdconfig.exe software only works with the 3200 or 3300 series digital clocks. Sapling’s USB to RS485 converter needs to be purchased separately. Other USB to RS485 converters will not work. • When using the sbdconfig software, ensure JP6 is on Pins 2&3 on the back of the digital clock board.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Setting up sbdconfig.exe (ctd.) 7. Scroll down to Universal Serial Bus controllers and click the + sign to open. 8. Double-click on the “USB Serial Converter” and a new window will open. If the USB Serial Converter does not appear, look for a new item called USB Half UART under the Device Manager category “Other Devices”.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Setting up sbdconfig.exe (ctd.) 10. Remove RS485 device from the USB port, wait 5 seconds, and plug it back into USB port. 11. Open the Device Manager and scroll to Ports. Make note of which port the USB Serial Port is assigned to. For example: (COM 4). 12. Load the sbdconfig.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Setting up sbdconfig.exe (ctd.) 14. Make sure that the Com port number matches the number you saw on the Device Manager, then click apply. 15. Click the ‘Read Clock’ button. The default settings will populate the tabs on the sbdconfig software. Once the ‘Read Clock’ button is clicked, another window will open that will signify the upload process. 16.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Task Bar Located on the task bar of the sbdconfig software, there are five options to choose from: Serial Port, Read Clock, Load Clock, Configurations, and Version. Serial Port Configure Serial Port: When clicked, this option will open the settings for the serial port (Fig. 1). This is where a user can manage the settings that connect a PC to the digital clock.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Task Bar (ctd.) Read Clock • If a user has a previously configured clock and connects it to a computer, this option will read and upload the settings to the sbdconfig software program. Once the ‘Read Clock’ button is clicked, another window will open that will signify the upload process (Fig. 2). (Fig.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Display Settings 1 2 3 8 9 4 5 6 7 Clicking on the Display Settings tab will allow a user to program the following settings: 1. Display Format - Allows the user to select how the time is displayed on the clock. There are two options: 12 hour format (3:00AM/3:00PM) or 24 hour format (3:00/15:00). 2.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Brightness Schedule 2 5 1 3 4 1. Clicking on the Brightness Schedule tab allows a user to establish a Brightness Schedule for the digital clock(s). 2. Date Column - Allows the user to select dates where changes to the brightness schedule are active. If a date is not selected, the actions in the adjustment columns will not be applied to the clock. 3.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Clock Settings 1 2 3 4 5 6 Clicking on the Clock Settings tab will allow a user to program the following settings: 1. Clock Name - This field allows a user to assign the clock a unique name, such as its location in a facility. The name cannot exceed 24 characters. 2. Clock Number - This field allows a user to assign a unique number to a clock.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Outputs Clicking on the Outputs tab will allow a user to program the following settings: RS485 Data Rate: This option determines how often data (time and date) is sent to the clock(s) or other Sapling devices, such as Wireless Repeaters, Converter Boxes, or other Master Clocks.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Elapsed Timer A user may set up and configure the Elapsed Timer control panel through sbdconfig. For detailed instructions on the many functions and uses of the Elapsed Timer, refer to the Elapsed Timer Manual.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Inputs The ‘Inputs’ tab allows a user to program the clock to perform a certain function through a switch or relay contact closure from an outside device such as Code Blue, Nurses Call, etc. Program the first Input on the 3300 digital clock by selecting one of the options in the drop down list next to Input 1.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Inputs (ctd.) Code Blue: Code Blue is a special-purpose count up designed for use in hospitals and other medical facilities. This function overrides the control panel LED settings. The lights are green while the timer is running and red when the timer has been paused. When an input programmed with Code Blue is activated for the first time, the count up starts.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com sbdconfig - Daylight Saving Time (DST) The DST Tab allows a user to configure the clock for automatic Daylight Saving Time changes. Select Method for Defining DST: This drop down allows a user to choose between four options for Daylight Savings Time. Day of Month: When this option is selected, Daylight Saving Time can be set based on what date and time it begins and ends.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Reading the Display The digital clock is designed to display time in either a 12-hour or 24-hour format. When the display is set to the 12-hour format, a circular light will appear in the top left corner of the display to indicate PM, or disappear to indicate AM.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Frequently Asked Questions Can this digital clock be used as a standalone clock? The 3300 digital clock can be used as a standalone clock, but it will not keep synchronized time in this configuration. Instead, it will rely on an internal quartz oscillator for keeping the time.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Frequently Asked Questions Will the wireless clock cause interference with other wireless devices? No. SBL Series Wireless Clocks work on 900 MHz (2.4GHz for SBTG) frequency-hopping technology, which allows the clock transmitters to avoid interfering with other devices operating on those frequencies.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Troubleshooting How can I determine that the clock is receiving a signal? if the clock is not receiving a signal, then the colons on the clock will blink on and off, unless configured by the user not to do so. This option is controlled through either the Manual Controls; Setting 13. The clock is not running. What do I do? 1. Measure the input voltage to the clock.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com Warranty Sapling Limited Warranty and Disclaimer The Sapling Company, Inc.
The Sapling Company, Inc. 670 Louis Drive Warminster, PA 18974 USA P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com FCC Statements The Federal Communications Commission (FCC) wants you to know: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protraction against harmful interference in a commercial installation.