OEM MANUAL August 2013 2.433-2.
Page 2 of 8 OEM INTEGRATOR ATTESTATION a. This module is for OEM installation only. b. The OEM is responsible for ensuring that the end-user has no manual instructions to remove or install module. c. The module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). d. Separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations. e.
Page 3 of 8 Introduction This module is only authorized to be installed in fixed mount installation and may not be installed in a mobile or portable device. The HPB-24G-1 module is to be used in Sapling Master Clocks such as the SMA3000 or SMA Repeater and equivalent models. The module is only to be connected to and installed in other Sapling products. Specifications The antenna gain is +2.15dBi maximum. The maximum output power will be 30 dBm.
Page 4 of 8 HPB-24G-1 Connectors P1 OPERATING CONNECTOR PIN 1 5 VOLTS PIN 2 GROUND PIN 3 PPS OUT PIN 4 TXD PIN 5 RXD PIN 6 MSTR/SLV PIN 7 STBY PIN 8 NO CONNECTION * PIN 1 IS SQUARE PAD. P2 PROGRAMMING CONNECTOR PIN 1 TDO/TDI PIN 2 3.3 VOLTS PIN 3 TDI PIN 4 3.3 VOLTS PIN 5 TMS PIN 6 NO CONNECTION PIN 7 TCLK PIN 8 TEST PIN 9 GROUND PIN 10 NO CONNECTION PIN 11 RST PIN 12 TXD PIN 13 SHIELD PIN 14 RXD * PIN 1 IS SQUARE PAD.
Page 5 of 8 SMA-1SR-G000-1 HPB-24G-1 FCC ID: R73HPB-24G-1 5 VOLT POWER SUPPLY P1 5 VOLT POWER & DATA BOARD P1 OPERATING CONNECTOR 5 VOLTS RED WIRE PIN 1 GROUND BLACK WIRE PIN 2 PIN 3 PPS OUT TXD ORANGE WIRE PIN 4 RXD VIOLET WIRE PIN 5 MSTR/SLV WHITE WIRE PIN 6 PIN 7 STBY PIN 8 NO CONNECTION * PIN 1 IS SQUARE PAD.
Page 6 of 8 The picture below shows the top of the SMA-1SR-G000-1 with HPB-24G-1 RF module antenna connector and the FCC ID and the Compliance Label. SMA-1SR-G000-1 SMA-1SR-G000-1 Label The label below is an example of the FCC ID and the Compliance Label.
Page 7 of 8 Installed The picture below shows the HPB-24G-1 RF module in a master clock. It shows the SMA-3S0-G008-1 and the connectors to the rest of the Sapling Wireless Clock System. FCC ID: R73HPB-24G-1 SMA-3S0-G008-1 5 VOLT POWER SUPPLY HPB-24G-1 P1 RELAY & CONTROL BOARD P1 OPERATING CONNECTOR P1 POWER & DATA 5 VOLTS RED WIRE PIN 1 GROUND BLACK WIRE PIN 2 PIN 3 PPS OUT TXD ORANGE WIRE PIN 4 RXD VIOLET WIRE PIN 5 MSTR/SLV WHITE WIRE PIN 6 PIN 7 STBY PIN 8 NO CONNECTION * PIN 1 IS SQUARE PAD.
Page 8 of 8 SMA-3S0-G008-1 Label The label below is an example of the FCC ID and the Compliance Label. Operation 1. The HPB-24G-1 RF module, as a repeater transceiver, will receive time from another transmitter or clock and re-transmit the time. 2. The HPB-24G-1 RF module, as a master clock transceiver, will transmit the time for 240 msec and receive the time for up to 20 seconds once a minute. FCC Statement: This device complies with part 15 of the FCC Rules.
