Computer Input Input Source Selection (Computer 2: RGB) Direct Operation Choose Computer 2 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below.
Computer Input Computer System Selection This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, WXGA, UXGA or WUXGA with its Multi-scan system and Auto PC adjustment. If a computer is selected as a signal source, this projector automatically detects the signal format and tunes to project a proper image without any additional settings.
Computer Input Auto PC adjustment Auto PC adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, Vertical, Clamp, Display area H and Display area V positions to conform to your computer. Menu Operation PC adjust Menu Auto PC adj. 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select PC adjust and then press the Point ► or the SELECT button. 2 Use the Point ▲▼ buttons to select Auto PC adj. and then press the SELECT button.
Computer Input Manual PC adjustment Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector. Manual PC adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has five independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 2 Press the MENU button to display the On-Screen Menu.
Computer Input Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select Yes. All adjustments will return to their previous figures. Mode free To clear the stored data, select Mode free and then press the Point ► or the SELECT button. Move the highlight to the mode that you want to clear and then press the SELECT button. Mode free Store To store the adjusted data, select Store and then press the Point ► or the SELECT button.
Computer Input Image Mode Selection Direct Operation Select the desired image mode among Dynamic, Standard, Real, Blackboard (Green), Colorboard, Image 1, Image 2, Image 3 and Image 4 by pressing the IMAGE button on the remote control. Remote Control IMAGE button Dynamic Standard Real IMAGE button Blackboard(Green) Colorboard Image 1 Menu Operation 1 2 Image 2 Press the MENU button to display the On-Screen Menu.
Computer Input Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image adjust and then press the Point ► or the SELECT button. 2 Use the Point ▲▼ buttons select the desired item and then press the SELECT button to display the adjustment dialog box. Use the Point ◄► buttons to adjust the setting value. Image Adjust Menu Contrast Press the Point ◄ button to decrease the contrast; press the Point ► button to increase the contrast (from 0 to 63).
Computer Input Store To store the adjusted data, select Store and press the Point ► or the SELECT button. Use the Point ▲▼ buttons to select one from Image 1 to 4 and press the SELECT button. A confirmation box appears and then select Yes. Stored data can be called up by selecting an Image (1–4) in the Image Mode Selection on page 36. Screen Size Adjustment A confirmation box appears and then select Yes. 1 Press the MENU button to display the On-Screen Menu.
Computer Input Custom Adjust the screen scale and position manually with this function. Press the Point ►button at Custom and the Custom is displayed on the screen, you can use the Point ▲▼ buttons to choose the item you want to adjust. Scale H/V........... Adjust the Horizontal/Vertical screen scale. H&V.................... When set to On, the aspect ratio is fixed. Scale V appears dimmed and becomes unavailable. Adjust Scale H, then the screen scale is automatically modified based on the aspect ratio.
Video Input Input Source Selection (Video, S-video) Direct Operation Choose Video or S-video by pressing the INPUT button on the top control or the VIDEO button on the remote control. Top Control INPUT button Computer 1 Computer 2 Remote Control HDMI Video VIDEO button Video S-video S-video Network COMPUTER 2 can not be selected when using the COMPUTER IN 2/MONITOR OUT terminal as MONITOR OUT output. Menu Operation 1 2 Press the MENU button to display the On-Screen Menu.
Video Input Input Source Selection (Component, RGB Scart 21-pin, HDMI) Direct Operation Choose Computer 1 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control; choose HDMI by pressing the INPUT button on the top control or press the HDMI button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below.
Video Input Video System Selection 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Input and then press the Point ► or the SELECT button. 2 Use the Point ▲▼ buttons to select Video , S-video or Computer 1(Component) and then press the SELECT button. 3 Use the Point ▲▼ buttons to select System and then press the Point ► or SELECT button. Use the Point ▲ ▼ buttons to select the desired system and then press SELECT button.
Video Input Image Mode Selection Direct Operation Remote Control Select the desired image mode among Dynamic, Standard, Cinema, Blackboard (Green), Colorboard, Image 1, Image 2, Image 3 and Image 4 by pressing the IMAGE button on the remote control. IMAGE button Dynamic Standard Cinema IMAGE button Blackboard (Green) Colorboard Menu Operation 1 2 Image 1 Press the MENU button to display the On-Screen Menu.
Video Input Image Adjustment 1 2 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Image adjust and then press the Point ► or the SELECT button. Image adjust Menu Use the Point ▲▼ buttons select the desired item and then press the SELECT button to display the adjustment dialog box. Use the Point ◄► buttons to adjust the setting value. Contrast Press the Point ◄ button to decrease the contrast; press the Point ► button to increase the contrast (from 0 to 63).
Video Input Sharpness Press the Point ◄ button to decrease the sharpness of the image; press the Point ► button to increase the sharpness of the image (from 0 to 15). Gamma Use the Point ◄► buttons to adjust the gamma value to obtain a better balance of contrast (from 0 to 15). Noise reduction Noise interference on the screen can be reduced. Select one of the following options to get smoother images. Off.......... Disabled. L1........... Lower reduction. L2........... Higher reduction.
Video Input Screen Size Adjustment This projector has the picture screen resize function, which enables you to customize the image size. 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Screen and then press the Point ► or SELECT button 2 Use the Point ▲▼ buttons select the desired item and then press the SELECT button. Screen Menu Normal Provide the image to fit the screen size while maintaining the aspect ratio of input signal.
Setting Setting This projector has a Setting menu that allows you to set up the other various functions described below. 1 2 3 Setting Menu Press the MENU button to display the On-Screen Menu. Press the Point ▲▼ buttons to select Setting and press the Point ► or the SELECT button to access the submenu items. Use the Point ▲▼ buttons to select the desired item and then press the Point ► or the SELECT button to access the selected item.
Setting Auto setup This function enables Input search, Auto Keystone correction and Auto PC adjustment by pressing the AUTO SETUP/ CANCEL button on the top control or the AUTO SET/CANCEL button on the remote control. Settings for those functions can be altered as follows: Input search This function detects the input signal automatically. When a signal is found, the search will stop. Use the Point ▲▼ buttons to select one of the following options. Off.......Input search will not work. On1.....
Setting Keystone This function is used to store or reset the keystone correction when the AC power cord is unplugged. Keystone Store........ Keep the keystone correction even when the AC power cord is unplugged. Reset........ Release the keystone correction when the AC power cord is unplugged. To correct keystone distortion, press the SELECT button. Keystone appears on the screen. Use the Point ▲▼ buttons to correct keystone distortion (p.26).
Setting Logo (Logo and Logo PIN code lock settings) This function allows you to customize the screen logo with Logo select, capture, Logo PIN code lock and Logo PIN code change functions. Note: When On is selected in the Logo PIN code lock function, Logo select, capture and Logo PIN code change cannot be selected. Logo select HDMI setup Terminal Pointer Standby mode Computer 2 Dot Eco Logo select This function decides on the starting-up display from among following options. User.........
Setting Capture This function enables you to capture an image being projected to use it for a starting-up display or interval of presentations. Capture Off Select Capture and press the SELECT button. A confirmation box appears and select Yes to capture the projected image. After capturing the projected image, go to the Logo select function and set it to User. Then the captured image will be displayed the next time you turn on the projector or when you press the NO SHOW button (see page 29).
Setting Enter a Logo PIN code Use the Point ▲▼ buttons to enter a number. Press the Point ► button to fix the number and move the red frame pointer to the next box. The number changes to . If you fixed an incorrect number, use the Point ◄ button to move the pointer to the number you want to correct, and then enter the correct number. Repeat this step to complete entering a four-digit number. Enter a Logo PIN code After a correct Logo PIN code is entered, the following dialog box appears.
Setting Ceiling Ceiling When this function is set to On, the picture will be top/ bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear Rear When this function is set to On, the picture will be left/right reversed. This function is used to project the image from rear of the screen. HDMI setup This function is only used for HDMI input source.
Setting Pointer You can emphasize a part of the projected image with this function. Use the Point ▲▼ buttons to choose Spotlight (Large, Middle or Small) , Arrow, Finger or Dot and press the SELECT button. See "Pointer Function" on page 14. Pointer Arrow Standby mode This function is available when operating the projector via network. Normal....... Supply the power to the network function even after turning off the projector.
Setting Picture in Picture This function is used to project two videos simultaneously by placing a separate small sub screen within the main screen. (Picture in Picture combinations provided in this projector are shown on pages 78.) Only the sound on the main picture is heard, the sound on the sub picture cannot be heard.( In P in P, the big picture is main picture, and the small one is sub picture; in P by P, the left picture is main picture, and the right one is sub picture.) Picture in Picture Mode. .
Setting Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not operated for a certain period. Select one of the following options: Ready................... When the lamp has been fully cooled down, the POWER indicator changes to green blinking.
Setting On start When this function is set to On, the projector will be automatically turned on just by connecting the AC power cord to a wall outlet. Note: Be sure to turn off the projector properly (see "Turning Off the Projector" on page 23). If the projector is turned off in the incorrect sequence, the On start function does not work properly. Closed caption Closed caption is a printed version of the program sound or other information displayed on the screen.
Setting Lamp control This function allows you to change brightness of the screen. Auto ����������� The brightness according to the input signal (between High and Eco mode). High ����������� Brighter than the Normal mode. Normal........ Normal brightness Eco ������������ Lower brightness reduces the lamp power consumption and extends the lamp life. Note: Lamp mode cannot be changed for a while after turning on the projector. Lamp needs some time to stabilize after the power is turned on.