Safe Handling and Precautions To use your purchased R/C System properly and safely, please read this instruction carefully and make sure to follow the precautions. Improper use of the product or negligence of following safety precautions can cause trouble to others or harm to the user. ■ For safety, please make sure to follow each of the precautions below. Warning Precautions for Installation and Operation When turning the power switch of R/C System on, please turn on in order of 1.Transmitter → 2.
Warning Careful When Driving When operating an RC car, please make sure to follow the following notes and avoid giving trouble to others. Maintain the body of the car (boat) in a perfect condition and check the safety. Do not operate an RC car in a crowd or on a public road. Make sure to disconnect the connector of the power battery and remove the power battery from the car after operation.
Safe Handling and Precautions Warning Note Precautions for Safe Use ● 2.4 GHz frequency band is not only used for radio control. This frequency band is shared with ISM (Industry, Science and Medical) band. It can be affected by microwave ovens, wireless LAN, digital cordless telephones, audio equipment, Bluetooth of game machines or cell phones and short-range communication such as VICS.
INDEX ■Structure and the Standard of the Set・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 5 ●Structure of the set (5) ●Set specification (5) ■Before Using・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 6-8 ●Adjusting tension of the steering and throttle, the grip pad (6) ●Adjusting the the full adjustable trigger (7) ●About the power source, about micro SD card (8) ■About connecting and installing the receiver・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 9-10 ●About the receiver, handling the antenna (9) ●About connecti
Structure and the Standard of the Set Structure and the Standard of the Set STRUCTURE OF THE SET MT-5 RX-493i PC (Primary Component) <A> Transmitter <B> Receiver Servo <C> <D> Accesories MT-5(TX-491) RX-493i Strap Hook x1 Trigger Angle Spacer x2 Brake Trigger +1/+2 x each 1 Grip Pad S size x1 Receiver Dust Cover x1 Bind Plug x1 Antenna Pipe x1 Sponge for Optional Battery x1 User Manual x1 ●Please check items before use SET SPECIFICATION <A> Transmitter Product No.
ADJUSTING THE STEERING AND THROTTLE TENSION MT-5 can adjust the tension of the steering/throttle trigger to match operation of the steering/throttle to the user’s preference. Adujsting the Steering Tension Before Using Before Using By inserting a hex wrench driver (1.5mm) to the place where the arrow is pointing at in the illustration on the right and turning, you can adjust the tension of the steering spring.
Before Using Before Using ADJUSTING THE FULL ADJUSTABLE TRIGGER Adjusting the trigger position Loosen the fixing screws of the trigger on the back of the transmitter. Then, adjust the adjusting screw of the trigger position on the back of the transmitter to set the trigger at the position of your preference. When you turn the adjusting screw of the trigger position clockwise, the trigger position gauge moves to the direction A.
You can adjust brake trigger position accroding to your fingers by replaceing the included brake trigger. Standard Size, +1 Size, +2 Size is included. 1) Remove the brake trigger fixing screw. 2) Select Brake Trigger according to your fingers. 3) Fix the brake trigger by the screw.
Connections and Installation of Receiver ABOUT THE RECEIVER Antenna Connections & Installation of Receiver BIND Plug LED *Indicate receiver working condition by LED light. Antenna pipe amount Please use SANWA antenna pipe. SSL/BAT: BIND/SSL Port * Please do not connect devices except SANWA SSL Compatible devices.
Please refer the below picture for receiver and servo connection ●Connection example in case of using in EP car BATT Power battery Connection with CH2 Before Using ABOUT CONNECTION SETUP Motor CH2 CH1 *When using PGS Servo with SGS-02, PGS servo cannot set by CODE10 at the same time. Only SGS-02 can be set when connect with PGS servo.
Names of each part of transmitter Carrying Handle (Movable) Display Panel LED *LED will be on when Telemetry is ON and Receiver Battery is OFF. LED will be flashing while Telemetry alarm is active.
Trigger Position Adjusting Screw When using the Strap Hook Internal Antenna Names of each part of the transmitter Power Switch Strap Hook Micro SD cover Remove the screw, attach the hook & tighten the screw *Make sure that the hook is facing the right direction Throttle Trigger Grip (Normal/Small) Connector Cover 12
Indicator Function (RX-DATA) ● MT-5 can check signal receiving conditions to use with RX-493i. The conditions can be used for devices glitch and checking receiver place on the car. There are 2 different types of data for checking signal condition. Received Signal Strength (RSS) Indicate signal strength which receiver received from the transmitter. The value will be changed by placing of receiver and antenna, RC circuit, places of operation.
When this happens... Symptom Cause Measure There is no power. Batteries are consumed. Batteries are placed improperly. Replace with new batteries or recharged batteries. Reinstall the batteries as the polarity is indicated. Power is cut off occasionally. Bad connection of connectors. Bring to Sanwa Service Insufficient length Batteries are consumed. Replace with new batteries or recharged batteries. If the problem cannot be solved, please contact Sanwa Service Alarm will not stop.
Service and Support This is warranted against manufacturer defects in materials and workmanship, at the original data of purchase. This warranty does not cover components worn by use or damage caused by improper voltage, tempering, modification, misuse, abuse, improper writing, reverse polarity, moisture or using outside its intended scope of use. Terms of this warranty can vary by region. Please read the warranty card included with your radio control system for specific warranty information.
ADJUSTING THE STEERING AND THROTTLE TENSION MT-5 can adjust the tension of the steering/throttle trigger to match operation of the steering/throttle to the user’s preference. Adujsting the Steering Tension Before Using Before Using By inserting a hex wrench driver (1.5mm) to the place where the arrow is pointing at in the illustration on the right and turning, you can adjust the tension of the steering spring.
Before Using Before Using ADJUSTING THE FULL ADJUSTABLE TRIGGER Adjusting the trigger position Loosen the fixing screws of the trigger on the back of the transmitter. Then, adjust the adjusting screw of the trigger position on the back of the transmitter to set the trigger at the position of your preference. When you turn the adjusting screw of the trigger position clockwise, the trigger position gauge moves to the direction A.
You can adjust brake trigger position accroding to your fingers by replaceing the included brake trigger. Standard Size, +1 Size, +2 Size is included. 1) Remove the brake trigger fixing screw. 2) Select Brake Trigger according to your fingers. 3) Fix the brake trigger by the screw.
Connections and Installation of Receiver ABOUT THE RECEIVER Antenna Connections & Installation of Receiver BIND Plug LED *Indicate receiver working condition by LED light. Antenna pipe amount Please use SANWA antenna pipe. SSL/BAT: BIND/SSL Port * Please do not connect devices except SANWA SSL Compatible devices.
Please refer the below picture for receiver and servo connection ●Connection example in case of using in EP car BATT Power battery Connection with CH2 Before Using ABOUT CONNECTION SETUP Motor CH2 CH1 *When using PGS Servo with SGS-02, PGS servo cannot set by CODE10 at the same time. Only SGS-02 can be set when connect with PGS servo.
Names of each part of transmitter Carrying Handle (Movable) Display Panel LED *LED will be on when Telemetry is ON and Receiver Battery is OFF. LED will be flashing while Telemetry alarm is active.
Trigger Position Adjusting Screw When using the Strap Hook Internal Antenna Names of each part of the transmitter Power Switch Strap Hook Micro SD cover Remove the screw, attach the hook & tighten the screw *Make sure that the hook is facing the right direction Throttle Trigger Grip (Normal/Small) Connector Cover 12
How to Use Each Feature ABOUT KEY OPERATION ● The user can set up and make a calling easily with the Multi-Selector and Select button/Back button. Display Panel Select Button Multi-Selector Back Button Key Operation How to Use Each Feature Push Push Names Performance Enter ●Moves to the setup screen from the top screen. ●Selects a feature and item to set. *By long pressing the Enter, the setting goes back to default. Multi-Selector UP ●The cursor moves upward. ●The set value increases.
ABOUT DISPLAY PANEL ● Each feature of MT-5 allows you to directly select a feature with the Multi-Selector. ● You can set up each channel feature separately. ● As you turn the power switch on, the top screen launches after the boost screen is displayed(when the boot setting is on). When changing each setting, select the menu by operating the Multi-Selector.
How to Use Each Feature ABOUT THE MENU STRUCTURE How to Use Each Feature ● The user can set up features and do model memory call easily by using each key. ● The Menu consists of Setting, AUX, CUSTOM, MODEL, TELEMETRY, TH-FUNCTION, TIMER and SYSTEM, and related features are included in each menu. CUSTOM SETTING TH‑FUNCTION (P.53) Custom Menu It is set with the Custom List within the System. D/R (P.19) SPEED (P.20) CURVE (P.21~24) F/S (P.25) BASE (P.26~28) TRIM (P.29、30) ALB (P.31) OFFSET (P.
ABOUT SHORT CUT MENU ● MT-5 has a feature of Short Cut Menu that is launched as the user performs key operation when operating the power switch. When you turn the power switch on with holding on the Back Button, it becomes the Direct Model Select. When you turn the power switch on with holding on Enter operation, the Quick Setup feature launches.
How to Use Each Feature ABOUT SHORT CUT MENU QUICK SETUP WIZARD ● Quick Setup 1) Turn the power switch on while doing Enter operation. Power Switch ON Push Holding ⇒ 2) Quick Setup screen is displayed. As you do Enter operation, Quick Setup Wizard is launched. ENTER BACK ENTER BACK ENTER BACK ENTER BACK How to Use Each Feature 3) When the screen is changed to Model selection screen, select a Model to set up by using Multi-Selector. When a Model to set is selected, set with Enter operation.
5) When deciding the car type using Enter, the screen changes to Initialization (Model Initialization) screen.Do initialization following the message. ENTER BACK ENTER BACK ENTER BACK ENTER BACK 6) When initializing (Initializing Model) is completed, the screen changes to RF Mode Selection Screen. MT-5 is only compatible FH5 RF mode.
How to Use Each Feature DUAL RATE [D/R] SETTING ● You can adjust rudder angle when operating the steering wheel and throttle trigger to their peak. To correspond to the RC car or road condition, adjust the rudder angle as you operate. *You can adjust steering for both right and left at the same time and throttle separately for high and brake sides. You can also adjust the brake side more precisely than adjusting with EPA.
SPEED SETTING ● Features to control the speed of the servos used for steering and throttle. By setting, the RC car is not affected even when doing a sudden operation. On the steering side, smooth corner work becomes possible and on the throttle side, stable rising from a corner by throttle work with saved power. *When setting AUX TYPE to [CODE5/CODE10], adjusting the speed feature of the AUX channel does not affect the performance.
How to Use Each Feature CURVE SETTING ● Function of making operation volume of servo variable with respect to the operation of the steering wheel, throttle trigger, AUX. It responds quickly when the set value is on plus (+) side whereas it responds mildly when the set value is on minus (-) side. ● Exponential (EXP) of curve operation and adjustable rate controller (ARC) of linear position can be selected.
[TH] THROTTLE EXPONENTIAL ● You can change the throttle feature from Mild to Linear and to Quick. In general, when operating on a slippery road or if you find over powering, change the setting to the minus side and when operating on a high-grip road or if you find lack of power in the power unit, change to the plus side. You can set the High side and the brake side separately. *Selection of the High side and the brake side is done by trigger operation.
How to Use Each Feature CURVE [ST] SETTING STEERING ADJUSTABLE RATE CONTROL ● You can change the steering feature from Mild to Linear and to Quick. In general, if you find your RC car oversteering, change the setting to the minus side and if you find understeering, change to the plus side. Steering Adjustable Rate Control is a simultaneous setting for L and R. 1) Select ST with the Select button and set CURVE TYPE of ST to [ARC] with the multi-selector.
[AUX1] AUX1・ADJUSTABLE RATE CONTROL ● You can change the AUX1 performance feature from Mild to Linear and to Quick. You can set the High side and the Low side separately. *When setting AUX1 to [CODE5/CODE10] in AUX TYPE, changing the setting does not affect the performance. 1) Select AUX1 with the Select button and set CURVE TYPE of AUX1 to [ARC] with the multi-selector. 2) Setting Rate [RATE] Select [RATE] with the multi-selector and adjust the setting value.
How to Use Each Feature FAIL SAFE [F/S] SETTING ● Fail Safe Operation is a feature to keep the servos in a predetermined position for each channel in the event that the receiver cannot receive a signal from the transmitter. A feature to keep the servos in a predetermined position for the servo of the throttle channel (2ch) in the event that the battery voltage on the receiver side of an engine RC car goes below the set voltage is Battery Fail Safe Operation.
BASE SETTING ● Base [BASE] is a feature to integrate features of the Reverse that determines the direction of the servo of each channel and the speed controller according to a specific RC car, the Sub Trim that adjusts the neutral position and the End Point Adjustment [EPA] that sets the operating quantity into one feature (Base) to allow you to make a setting all at once. REVERSE [REV] ● This is used when operation and the movement of the servo are reversed while operating Steering/throttle/ AUX1/AUX2.
How to Use Each Feature BASE SETTING ● Base [BASE] is a feature to integrate features of Sub Trim that adjusts the direction of the servo of each channel and the speed controller according to a specific RC car and the End Point Adjustment [EPA] that sets the operating quantity into one feature (Base) to allow you to make a setting all at once.
[AUX1-EPA] AUX1・END POINT ADJUSTMENT ● You can use AUX1 for functions of accessories and adjust the maximum steering angle (operating quantity) with EPA. Since you can set H/L separately, precise adjustment is possible. *When setting AUX1 to [CODE5/CODE10] in AUX TYPE, the operation will not be refected even by adjusting EPA. 1) Before adjusting AUX1 End Point Adjustment (AUX1-EPA), make a neutral adjustment of the servo (P. 26).
How to Use Each Feature TRIM SETTING ● For Trim, you can adjust Trim for each channel and set the Trim action (center/parallel). TRIM ● Correct neutral (center) of each channel (ST/TH/AUX1/AUX2) with Trim. ● As default, steering is set for Trim 1 (TRM1), and throttle for Trim 2 (TRM2). 1) Select a channel (ST/TH/AUX1/AUX2) for adjusting Trim with the Select button. 2) Determine with Enter operation and adjust with the multi-selector.
CONVERT ● A feature to convert Trim that has been adjusted in each channel to Sub Trim and EPA and to correct Trim to center. Depending on a setting, there is a case you cannot convert. 1) Select a channel (ST/TH/AUX1/AUX2) to convert with the Select button. 2) Once a channel to set is determined, launch the convert feature with Enter operation. 3) For example, if the converting feature is used when SteeringTrim is [L20] and each [EPA] is 100%, the flow will be as shown in right illustration.
How to Use Each Feature THROTTLE FUNCTION ● The throttle function allows you to adjust the setting values of ALB (Anti-Lock Brake), OFFSET and TH TYPE (throttle type) of the throttle channel. ANTI-LOCK BRAKE [ALB] THROTTLE FUNCTION ● Anti-Lock Brake enables stable braking on a low grip road. ● Because of the stable braking, you can trace cornering lines as intended. 1) Select the throttle function with the multi-selector and determine with the Enter operation.
OFFSET THROTTLE FUNCTION 2) Select [OFFSET] with the multi-selector and determine with Enter. It will change to OFFSET Setting menu. OFFSET Position When setting plus OFFSET Position Neutral postion When setting plus 3) Setting Offset [OFFSET] Set ON/OFF of the Offset feature with the multi-selector. ○ Setting Range: ON/OFF ○ Default: OFF OFFSET Position Neutral positionwhen setting minus OFFSET Position When setting minus 4) Setting Type [TYPE] Set Type of the Offset with the multi-selector.
How to Use Each Feature AUX ● AUX is a feature to set the performance of AUX1 and AUX2 (3ch, 4ch). You can choose from STEP AUX (STEP), POINT AUX (POINT), 4WS (4-Wheel Steering: Coordinate Phase, Opposite Phase). MOA (Motor On Axle), AUX-MIX (AUX Mixing: ST → AUX/TH-AUX) and CODE5/CODE10 (Code Communication). *Setting of AUX TYPE is done in the System Menu. Make a setting according to the purpose of the use.
4-WHEEL STEERING AUX ● With the operation of assigned Trim or Switch, control the motion of the 4 Wheel Steering. 1) Select [AUX] with the multi-selector and define with the Enter operation. 2) Setting Operating Mode Set the Operating Mode of 4WS with the multi-selector. Set the Operating Mode according to the usage. *When using during operation, assign the feature of the Operating Mode to Trim or the switch1.
How to Use Each Feature AUX ● AUX is a feature to set the performance of AUX1 and AUX2 (3ch, 4ch). You can choose from STEP AUX (STEP), POINT AUX (POINT), 4WS (4-Wheel Steering: Coordinate Phase, Opposite Phase). MOA (Motor On Axle), AUX-MIX (AUX Mixing: ST → AUX/TH-AUX) and CODE5/CODE10 (Code Communication). *Setting of AUX TYPE is done in the System Menu. Make a setting according to the purpose of the use.
CODE AUX AUX ● Code AUX (CODE AUX) is a feature to perform code communication by assigning a setting value to each code of CODE5/CODE10 It is an extension feature to change the setting of speed controller (SUPER VORTEX series/ SV-D2), PGS servo series, and the Gyro System (SGS-01C/SGS01D/SGS-02) that are compatible to CODE AUX. ● You can set 2 types of Code AUX1 and CODE AUX2. *Setting of CODE is done by setting [TYPE] of [SYSTEM] menu.
How to Use Each Feature TIMER ● It has three timer features including Lap Timer, Interval Timer and Down Timer. ● When selecting a timer and operate the Select button, you can toggle between the timer screen and the setting screen. *When a timer is activated, X Illumination and Function LED flash. ● You can check the lap time measured on the LAP TIMER screen. ● When Enter is being operated while Lap Timer is activated/not activated, the screen is changed to the Lap Time display.
5) Setting START Set the Timer Start from the Trigger Interlock/Switch/Random. ○ Setting Range: TRIGGER/KEY/STARTER ○ Default: TRIGGER 6) Setting DATA-LOG It sets Telemetry Data Log (record) along with the timer. Function LED X Illumination ○ Setting Range: ON/OFF ○ Default: ON *Log starts along with the timer feature. LAP TIMER LED flashes while the timer is activated. TIMER ● You can measure and record each lap up to 999 laps (works for all models).
How to Use Each Feature INTERVAL TIMER TIMER ● It activates the alarm at the time set at the beginning of running and uses it as the guideline for the goal time. 1) Select [TIMER] with the multi-selector and determine with the Enter operation. 2) Setting the Type [TYPE] Operate the Select button and select [INT] with [TYPE]. ENTER BACK 3) Setting Interval (INTERVAL) Set the Interval Timer with [INTERVAL]. 4) Starting Interval Timer As a default, the timer switch is set to SW1.
TELEMETRY ● A menu for setting Telemetry-related LOG DATA, TELEMETRY SETTING, GRAPH SETTNG and TELEMETRY SWITCH. ● To use the Telemetry feature, you can make it compatible by using a compatible receivers, SUPER VORTEX series / Gen2 / PRO / SV-D2. * Telemetry data is only capable with SANWA compatible devices. Telemetry data cannot be displayed in case of using other manufacture products. *About voltage on the telemetry data, the voltage is not directly from battery.
How to Use Each Feature VIEW DATA TELEMETRY ● A menu to read the recorded log data and creates a graph. 1) Select [LOG DATA] with the multi-selector and determine with the Enter operation. 2) Select LOG DATA to create a graph and determine with the Enter operation. How to Use Each Feature 3) By selecting the log data, a menu will be displayed.By selecting [VIEW DATA], the log data is displayed as a graph.
EXPORT [.CSV] TELEMETRY ● A feature to convert the selected log data to a graph with PC (Personal Computer) software such as a spreadsheet software. ● Please note that data converted by the Export feature cannot be converted to a graph with the transmitter. ● When using the Export feature, a micro SD card is necessary. ENTER BACK ENTER *You can cancel the conversion operation during converting data with the back operation.
How to Use Each Feature TELEMETRY TELEMETRY SETTING TELEMETRY ● Set each feature of Telemetry. Select the feature to set with the select button. • RPM: Setting the Speed figured from the number of rotation data [UNIT]: Switching the number of rotation and the speed display (RPM, km/ h, mph) [MAX SCALE]: Setting the graph's minimum value when displaying the data as a graph.
GRAPH SETTING TELEMETRY ● A feature to select 3 items to be displayed in a graph when displaying Telemetry data as a graph. 1) Select [TELEMETRY] with the multi-selector and determine with the Enter operation. 2) Setting GRAPH SETTING Select [GRAPH SETTING] with the multi-selector and determine with the Enter operation.
How to Use Each Feature MODEL MENU MODEL ● You can set the features about Model Select, Model Name, Model Copy and Model Clear. ● Installed with high capacity EEPROM and it can memorize data for 20 models of M01 ~ M20. MODEL SELECT ● You can call model data of memorized M01 ~ M20 easily. 1) Select [MODEL] with the multi-selector and determine with the Enter operation. 2) Setting Model Select (MODEL SELECT) Select [MODEL SELECT] with the multi-selector and determine with the Enter operation.
MODEL NAME ● You can register a model name with up to 12 characters of alphabets, numbers, EU Font and symbols for each model. 1) Select [MODEL] with the multi-selector and determine with the Enter operation. 2) Setting Model Name [MODEL NAME] Select [MODEL NAME] with the multi-selector and determine with the Enter operation. ENTER BACK ENTER BACK 4) Select texts to enter with the multi-selector. Once the texts to enter are determined, enter with the Enter key.
How to Use Each Feature MODEL MENU MODEL ● You can set the features about Model Select, Model Name, Model Copy and Model Clear. ● Installed with high capacity EEPROM and it can memorize data for 20 models of M01 ~ M20. MODEL COPY ● You can copy a selected model data to another model. 1) Select [MODEL] with the multi-selector and determine with the Enter operation. 2) Setting Model Copy [MODEL COPY] Select [MODEL COPY] with the multi-selector and determine with the Enter operation.
● About copying from a micro SD card When performing Model Copy, the main body memory and a micro SD card can select designation of the copy source and the copy destination. When selecting a Model on the copy destination selection screen, you can select with the Select button operation. 1) When a model is selected, designation of the copy source and the copy destination other than the main body memory can also be selected.It is switched by the operation of the select button.
How to Use Each Feature SYSTEM MENU SYSTEM ● A feature for setting system of the transmitter, such as Bind (BIND), Key Assignments (KEY ASSIGN), BUZZER (Buzzer), Battery (BATTERY), LCD and CALIBRATION (Calibration). BIND ● Select the output system that suits the receiver, set a mode for the servo (analog/digital) and the speed controller to be used and bind the transmitter with the receiver. When using first time, please bind with receiver.
6)Setting Channel Mode Set the response mode for each channel with Up key/Down key. ・You can the set the response mode for each channel. ○ Setting Range: NOR(Normal) SHR(High Response) SSR(Super Response) SUR (Ultra Response) ○ Default: NOR IMPORTANT 7) Setting BIND ● What is BIND: Each of MT-5 transmitters has its own unique ID (solid identification) number. BIND is to let the receiver memorize the ID number.
How to Use Each Feature SYSTEM MENU Positions of the Switch and Trim TRIM4 TRIM2 SYSTEM TRIM1 DIAL TRIM3 SWITCH2 Features assgined to the Switch and Trim at the factory TR1:Steering Trim(TRM-ST) TR2:Throttle Trim(TRM-TH) TR3:Dual Rate ST(D/R-ST) TR4:Dual Rate BR(D/R-BR) SW1:Timer (TIMER) SW2:CUSTOM PUSH SWITCH1 How to Use Each Feature KEY ASSIGN SWITCH ● You can assign features to the switches (SW1, SW2, SW3) of the transmitter and toggle ON/OFF of the features during operation.
KEY ASSIGN TRIM ● You can change the setting value of each feature with Trim1 - Trim4. ● You can also change the setting of the variation change in one time of Trim operation with the STEP setting and the direction of the action with the REV setting. 1) Select [SYSTEM] with the multi-selector and determine with the Enter operation. 2) Select [KEY ASSIGN] with the multi-selector, switch to [TRIM] with the Select button, select an item to set and determine with the Enter operation.
How to Use Each Feature SYSTEM MENU SYSTEM CUSTOM-LIST ● By setting an often-used menu onto the custom list, you can build your favorite menu. You can create a custom list for each model memory and you can create a 4-page list. ● A menu set with the custom list will be usable in custom. 1) Select [SYSTEM] with the multi-selector and determine with the Enter operation. 2) Select [CUSTOM-LIST] with the multi-selector and determine with the Enter operation.
AUX TYPE ● A feature to set the performance of AUX1 and AUX2 (3ch and 4ch). 1) Select [SYSTEM] with the multi-selector and determine with the Enter operation. 2) Select [AUX TYPE] with the multi-selector and determine with the Enter operation. 3) Set AUX TYPE with the multi-selector.
How to Use Each Feature SYSTEM MENU SYSTEM RACING MODE ● A feature to adjust the running characteristics of your RC car by switching the Racing Mode so that the features compatible to the Racing Mode can respond to your RC car and road conditions. ● It allows you to set two setting values of R1 and R2 individually for features that are compatible to the Racing Mode for each Model Memory, and to change by the switches that are assigned during operation.
BATTERY ● You can change the voltage setting of the battery alarm of the transmitter. ● By selecting Type [DRYx3 (Batteries)/Ni-MHx3 (Nickel Hydride)/Li-Pox1 (Lithium Polymer),CUSTOM], you can set the alarm easily. *When selecting CUSTOM with the Type, you can set ALERT VOLT that sets voltage to make Alarm go off and LIMIT VOLT of the lower voltage.
How to Use Each Feature SYSTEM MENU SYSTEM LCD ● You can set LCD (Liquid Crystal) contrast (intensity), brightness and lighting mode (lighting time) of Back Light. 1) Select [SYSTEM] with the multi-selector and determine with the Enter operation. How to Use Each Feature 2) Select [LCD] with the multi-selector and determine with the Enter operation. 3) Set LCD (Liquid Crystal Display) contrast (intensity), brightness and lighting mode (lighting time) of Back Light.
CLOCK ● A menu to control the calendar and the clock display on the top screen and the time used. ● There are resettable [ON TIME1] that is a guideline for replacing and recharging the batteries and [ON TIME2] that is a guideline for overhaul of the main body unit. 1) Select [SYSTEM] with the multi-selector and determine with the Enter operation. 2) Select [CLOCK] with the multi-selector and determine with the Enter operation. ENTER BACK 3) Set the CLOCK feature with the multi-selector.
How to Use Each Feature SYSTEM MENU SYSTEM CALIBRATION ● Due to wearing and tearing of the internal mechanical elements over the usage time, the neutral position and the operation angle might become off. In such case, you can correct the neutral positions of the steering and the throttle and the operation angle. 1) Select [SYSTEM] with the multi-selector and determine with the Enter operation. 2) Select [CALIBRATION] with the multi-selector and determine with the Enter operation.
FIRMWARE ● You can check the firmware version installed on the main body unit and the language file, and run updating. 1) Select [SYSTEM] with the multi-selector and determine with the Enter operation. 2) Select [FIRMWARE] with the multi-selector and determine with the Enter operation. 3) When updating the firmware and the language file, download the data file onto the micro SD card to proceed. ENTER BACK Unless you insert a micro SD card, it will not be displayed.
Assign Function List 61 Screen Display Name of the Features TRIM/Dial SW1 SW2 OFF ASSIST-ST TRIM-ST TRIM-TH TRIM-A1 TRIM-A2 D/R-ST D/R-TH D/R-BR CUR-ST CUR-TH CU-R-ST CU-R-TH CU-R-BR SPD-ST SPD-TH SP-ST-F SP-ST-R SP-TH-F SP-TH-R ALB ALB-PO ALB-ST ALB-LG ALB-CY OFFSET AUX1 AUX1[CD1] AUX1[CD2] AUX1[CD3] AUX1[CD4] AUX1[CD5] AUX1[CD6] AUX1[CD7] AUX1[CD8] AUX1[CD9] AUX1[CD10] AUX2 AUX2[CD1] AUX2[CD2] AUX2[CD3] AUX2[CD4] AUX2[CD5] AUX2[CD6] AUX2[CD7] AUX2[CD8] AUX2[CD9] AUX2[CD10] TIMER MAX-CLR CUSTOM RX-M
Indicator Function (RX-DATA) ● MT-5 can check signal receiving conditions to use with RX-493i. The conditions can be used for devices glitch and checking receiver place on the car. There are 2 different types of data for checking signal condition. Received Signal Strength (RSS) Indicate signal strength which receiver received from the transmitter. The value will be changed by placing of receiver and antenna, RC circuit, places of operation.
INDEX A Anti-Lock Brake [ALB]・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.31 AUX・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.33-36 AUX Mixing [AUX-MIX]・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ P.35 B BASE・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・ P.26 BATTERY・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・P.56 BIND・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.49, P.
When this happens... Symptom Cause Measure There is no power. Batteries are consumed. Batteries are placed improperly. Replace with new batteries or recharged batteries. Reinstall the batteries as the polarity is indicated. Power is cut off occasionally. Bad connection of connectors. Bring to Sanwa Service Insufficient length Batteries are consumed. Replace with new batteries or recharged batteries. If the problem cannot be solved, please contact Sanwa Service Alarm will not stop.
Service and Support This is warranted against manufacturer defects in materials and workmanship, at the original data of purchase. This warranty does not cover components worn by use or damage caused by improper voltage, tempering, modification, misuse, abuse, improper writing, reverse polarity, moisture or using outside its intended scope of use. Terms of this warranty can vary by region. Please read the warranty card included with your radio control system for specific warranty information.
FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operating instructions, may cause harmful interference to radio communications.
1 9.30.