User's Manual

ManualsBrandsSanwa Electronic Instrument ManualsElectronics2.4GHz RADIO CONTROL SYSTEM

STYLUS

receiver information

FHSS Module

Airtronics 2.4GHz FHSS receivers can be purchased and paired with your Stylus 2.4GHz FHSS module-equipped transmitter through

the Binding operation. Please note that due to differences in the implementation of 2.4GHz technology among different manufacturers,

only Airtronics brand 2.4GHz FHSS aircraft receivers are compatible with the Stylus 2.4GHz FHSS module.

The following receivers are compatible with the Stylus 2.4GHz FHSS module:

92824 8-Channel 2.4GHz FHSS

92674 7-Channel 2.4GHz FHSS

92664 6-Channel Micro 2.4GHz FHSS

2.4GHz frequency Band Precautions

The 2.4GHz frequency band may be used by other devices, or other devices in the immediate area may cause interference on the

same frequency band. Always before use, conduct a bench test to ensure that the servos operate properly. Also, conduct a range

test at the area of operation to ensure that the radio control system has complete control of the model at the farthest reaches of the

operational area.

The response speed of the receiver can be affected if used where multiple 2.4GHz radio control systems are being used; therefore,

carefully check the area before use. Also, if response seems slow during use, discontinue use as quickly as possible.

If the 2.4GHz frequency band is saturated (too many radio controllers on at once), as a safety precaution, the radio control system

may not bind. This ensures that your radio control system does not get hit by interference. Once the frequencies have been cleared,

or the saturation level has dropped, your radio control system should be able to bind without any problems.

 Observeanyapplicablelawsandregulationsinplaceatyouryingsitewhenusingthe2.4GHzradiocontrolsystem.

Unlike frequency bands used with earlier radio control systems, reception with this 2.4GHz radio control system can be adversely

affected by large obstructions and concrete or steel structures between your model and the transmitter. Also, wire mesh and similar

barriers can adversely affect operation. Keep this mind to ensure the safety of your model.

This module operates on the 2.4GHz frequency band. The 2.4GHz connection is determined by the transmitter and receiver pair.

Unlike ordinary crystal-based systems, your model can be used without frequency control.

Be certain to read this Operating Manual in its entirety.

'Safety First' for yourself, for others, and for your equipment.

 Observealltherulesoftheyingsiteoranywhereyouoperateyourradiocontrolequipment.

If at any time during the operation of your model should you feel or observe erratic operation or abnormality, end your operation as

quickly and safely as possible. DO NOT operate your model again until you are certain the problem has been corrected.

Your model can cause serious damage or injury, so please use caution and courtesy at all times.

If you have little to no experience operating models, we strongly recommend you seek the assistance of experienced modelers or your

local hobby shop for guidance.

safety

Convert your Stylus transmitter to 2.4GHz FHSS Spread Spectrum technology with this high-quality module and antenna set. It is quick

and easy to install and allows you to easily switch back to 72MHz in less than a minute! Requires an Airtronics 2.4GHz FHSS receiver

(not included). For a list of compatible receivers, see the Receiver Information section below.

The Stylus 2.4GHz FHSS module is not compatible with the Airtronics 92104

10-Channel 2.4GHz FHSS-3 receiver from the SD-10G.

Summary of content (4 pages)

PAGE 1
STYLUS FHSS Module Convert your Stylus transmitter to 2.4GHz FHSS Spread Spectrum technology with this high-quality module and antenna set. It is quick and easy to install and allows you to easily switch back to 72MHz in less than a minute! Requires an Airtronics 2.4GHz FHSS receiver (not included). For a list of compatible receivers, see the Receiver Information section below. This module operates on the 2.4GHz frequency band. The 2.4GHz connection is determined by the transmitter and receiver pair.
PAGE 2
.4GHZ MODULE INSTALLATION Installing the 2.4GHz module and antenna onto your Stylus transmitter only takes a few minutes. To install the 2.4GHz module and antenna, follow the steps below: 1) Carefully remove the existing module from the back of your transmitter. To remove the module, firml squeeze the two tabs on the sides of the module and pull the module straight out. 2) Remove the existing antenna from your transmitter.
PAGE 3
1) Turn the transmitter ON. The Bind LED on the module will illuminate solid blue. 2) While holding down the Bind Button on the receiver, turn the receiver ON. The Bind LED on the receiver will blink slowly. After ~ 2 seconds release the Bind Button. The Bind LED on the receiver will continue to blink slowly. Use the tip of a pencil or a 1.5mm hex wrench to press the Bind Button on the receiver. 3) Quickly press the Bind Button on the module.
PAGE 4
FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instrucitons, may cause harmful interference to radio communications.