WSWM21 and WSWM22 WIRELESS SPEAKER WALL MOUNT INSTRUCTION MANUAL WE’RE HERE TO HELP If you have any questions along the way, our US-based install experts are standing by to help. Call us at: 800-359-5520 Or, chat at: SANUS.
CAUTION: IMPORTANT SAFETY INSTRUCTIONS — PLEASE READ ENTIRE MANUAL PRIOR TO USE — SAVE THESE INSTRUCTIONS Before getting started, let’s make sure this product is perfect for you! This mount is designed to support Sonos® One™, PLAY:1™ and PLAY:3™ speakers, as well as other wireless speakers with similar mounting holes. CAUTION: Avoid potential personal injuries and property damage! Check your speaker owner’s manual to see if there are any special requirements for mounting your speaker.
Dimensions 3-D TV INTERFACE 0.45 11.5 2X 0.26 6.6 2.10 53.3 3.83 97.2 1.99 50.6 TOP VIEW - SONOS® One™ / PLAY:1™ WALL PLATE SIDE VIEW - SONOS® One™ / PLAY:1™ 0.25 6.4 9° 0.20 5.1 THRU 3.00 76.1 3.50 88.9 66° 0.20 5.1 5.00° 132° 1.73 44.0 TOP VIEW - SONOS® PLAY:3™ FULLY ASSEMBLED MOUNT 27° PLAY:1 18° SONOS One SIDE VIEW - SONOS® PLAY:3™ 9 224 9° 2.43 61.6 2.77 70.3 PLAY 3 2.70 68.
Supplied Parts and Hardware WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts! NOTE: Not all hardware included will be used. Quantities shown are for one speaker mount. STEP 1 Parts and Hardware Wall Plate Screw #10 x 1¾ in.
STEP 2 Parts and Hardware Interface Screw 10-24 x 1/2 in.
STEP 1A Attach Wall Plate to Wall Drywall Only Installation CAUTION: Avoid potential personal injury or property damage! ● 1 Drywall covering the wall, must not be less than 1/2 in. (12.7 mm) Mark hole locations BETWEEN studs. UP Min. 1/2 in. (12.7 mm) 2 3 Drill two holes. Insert two Anchors, flush with drywall. 1 in. (25 mm) 1/4 in. (6.
CAUTION: Avoid potential personal injury or property damage! Both screws 02 MUST BE firmly tightened to prevent unwanted movement of the wall plate 01 . Ensure the wall plate is securely fastened to the wall before continuing on to the next step. 4 5 Secure wall plate to wall. 01 Loosen lower screw for level adjustment - tighten when finished. 01 02 02 Go to STEP 2, PAGE 12.
STEP 1B Attach Wall Plate to Wall Wood Stud Installation CAUTION: Avoid potential personal injury or property damage! ● ● ● 1 Drywall covering the wall, must not exceed 5/8 in. (16 mm) Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1½ x 3½ in. (38 x 89 mm) Stud center must be verified Locate your stud CENTER. 2 Mark two hole locations. 3 Drill two holes. Max. 5/8 in. (16 mm) 1 ¾ in. (45 mm) UP 1/8 in.
CAUTION: Avoid potential personal injury or property damage! Both screws 02 MUST BE firmly tightened to prevent unwanted movement of the wall plate 01 . Ensure the wall plate is securely fastened to the wall before continuing on to the next step. 4 5 Secure wall plate to wall. 01 Loosen lower screw for level adjustment - tighten when finished. 01 02 02 Go to STEP 2, PAGE 12.
STEP 1C Attach Wall Plate to Wall Solid Concrete or Concrete Block Installation CAUTION: Avoid potential personal injury or property damage! ● ● ● 1 Mount the wall plate 01 directly onto the concrete surface (no wall covering) Minimum solid concrete thickness: 8 in. (203 mm) Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm) Mark two hole locations. 2 3 Drill two holes. Insert two Anchors, flush with drywall. 2 in. (50 mm) UP 1/4 in. (6.
CAUTION: Avoid potential personal injury or property damage! Both screws 02 MUST BE firmly tightened to prevent unwanted movement of the wall plate 01 . Ensure the wall plate is securely fastened to the wall before continuing on to the next step. 4 Secure wall plate to wall. 5 Loosen lower screw for level adjustment - tighten when finished.
STEP 2 Attach Mount to Speaker Based on your speaker model, follow the correct STEP 2 below.
STEP 2A /2B Attach Mount to Speaker For a helpful install video, search your model at SANUS.com. SONOS® One ™ Follow the step below based on your installation. TIP: Set up your Sonos® speaker prior to mounting. STEP 2A ABOVE EYE-LEVEL (speaker upside down) Follow PAGE 14. STEP 2B BELOW EYE-LEVEL (speaker right-side up) Follow PAGE 16.
Above Eye Level STEP 2A 1 Attach interface 06 to mount 04 with screw 08 . Attach Mount to Speaker 2 Remove screws S and open clamps. S SONOS® One™ Attach wires 07 (SMALL loop) to FIXED ends of bracket 06 .
CAUTION: Avoid potential personal injury or property damage! Wires 07 must NOT extend beyond the speaker's end caps. 4 Slide over speaker and attach wires 07 to CLAMP ends of bracket 06 . 5 Align wires 07 and close clamps. CAUTION: Avoid potential personal injury or property damage! Both screws S MUST BE installed to secure the speaker to the mount. 6 Secure with screws S . TIP: Rest speaker UPSIDE DOWN. S 07 07 06 06 Go to STEP 3, PAGE 21.
Below Eye Level STEP 2B 1 Attach interface 06 to mount 04 with screw 08 . Attach Mount to Speaker 2 Remove screws S and open clamps. 3 SONOS® One™ Attach wires 07 (SMALL loop) to FIXED ends of brackets 06 .
CAUTION: Avoid potential personal injury or property damage! Wires 07 must NOT extend beyond the speaker's end caps. 4 Slide over speaker and attach wires 07 to CLAMP ends of bracket 06 . 5 Align wires 07 and close clamps. CAUTION: Avoid potential personal injury or property damage! Both screws S MUST BE installed to secure the speaker to the mount. 6 Secure with screws S . TIP: Rest speaker on flat surface. S 07 07 06 06 Go to STEP 3, PAGE 21.
STEP 2C Attach Mount to Speaker SONOS® PLAY:1™ [and other speakers] Attach the mount 04 to your speaker with the speaker screw 09 . NOTE: Speaker may be installed in either the right-side-up position a or up-side-down position b , depending on height placement. a Right-Side-Up for BELOW Eye Level. b Up-Side-Down for ABOVE Eye Level. 09 04 04 09 18 Go to STEP 3, PAGE 21.
STEP 2D - (VERTICAL) 1 Attach interface 05 to mount 04 with interface screw 08 . Attach Mount to Speaker 2 Insert both legs L into the 4th holes from the top, to align the screw hole H . 3 SONOS® PLAY:3™ Secure the assembly with the speaker screw 09 . 05 04 L L 05 05 08 05 09 01 H Go to STEP 3, PAGE 21.
STEP 2E - (HORIZONTAL) 1 Attach interface 05 to mount 04 with interface screw 08 . Attach Mount to Speaker 2 Insert both legs L into the 4th holes from the end, to align the screw hole H . 3 SONOS® PLAY:3™ Secure the assembly with the speaker screw 09 .
STEP 3 1 Mount Assembly to Wall Plate 2 Install cables One™ 3 Slide onto wall plate 01 . Slide cap 10 onto mount 04 .
Adjustments TILT SWIVEL Your speaker can tilt up or down. Your speaker can swivel left or right. Play:1™ Shown One™ Reset Button Access Play:1™ Shown 22 Access your Sonos® Infinity button, through the hole on mount 04 , using tool 11 .
To Remove One™ 04 PLAY:1™ 04 PLAY:3™ [and other speakers] 01 Play:1 Shown One™ 10 S 10 PLAY:1™ [and other speakers] 07 PLAY:3™ 04 04 06 09 07 IMPORTANT: Set on flat surface.
ESPAÑOL INSTRUCCIONES IMPORTANTES DE SEGURIDAD: GUARDE ESTAS INSTRUCCIONES Y LEA TODO EL MANUAL ANTES DE UTILIZAR ESTE PRODUCTO. Antes de comenzar, verifiquemos que este producto sea el ideal para sus necesidades. PRECAUCIÓN: Evite posibles lesiones personales y daños materiales. ● Consulte el manual del usuario de su altavoz para ver si existe algún requisito especial para instalar su altavoz en la pared.
Dimensiones página 3 ESPAÑOL Piezas y elementos de sujeción suministrados página 4 ADVERTENCIA: Este producto contiene piezas pequeñas que, en caso de ser tragadas, podrían causar asfixia. Antes de comenzar a montar la unidad, verifique que dispone de todas las piezas y que se encuentran en buen estado. Si no dispone de todas las piezas o alguna está dañada, no devuelva el elemento defectuoso al distribuidor. Póngase en contacto con el servicio de atención al cliente.
ESPAÑOL PASO 2 Fijar el soporte de pared al altavoz página 12 Siga los siguientes pasos según el estilo de su altavoz. Para Sonos® One™ - consulte PASO 2A/2B en la PÁGINA 13 Para Sonos® Play:1™ - consulte PASO 2C en la PÁGINA 18 Para Sonos® Play:3™ (vertical) - consulte PASO 2D en la PÁGINA 19 Para Sonos® Play:3™ (horizontal) - consulte PASO 2E en la PÁGINA 20 PASO 2A/2B Fijar el soporte de pared al altavoz Siga los siguientes pasos basados en su instalación.
ESPAÑOL PASO 2C Fijar el soporte de pared al altavoz Fije el soporte 04 al altavoz Play:1 con el tornillo del altavoz 09 . NOTA: Puede instalar el altavoz con la parte derecha hacia arriba (a) o boca abajo (b), en función de sus necesidades. PASO 2D - (vertical) 1. 2. 3. 3. Sonos® Play:3™ Fijar el soporte de pared al altavoz Sonos® Play:3™ página 20 Fije el soporte de conexión del Play:3 05 al soporte 04 con el tornillo 08 .
Thank you for choosing SANUS! Please take a moment to let us know how we did: Call us: 1-800-359-5520 Email us: info@sanus.com Leave a review: sanus.com Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions, or variations.