Owner's Manual

ManualsBrandsSanus ManualsFurnitureMD-115

Table Of Contents

Assembly Instructions
- Supplied Parts & Hardware
- Assembly

SANUS

SYSTEIVIS

MOllS

6901-100054 <02>

Thank you

for

choosing

the

Sanus Systems

MOllS

Desk

Mount.

The Sanus Systems

MOllS

Desk

Mount

designed

support

monitors sized

30 in. (76 cm) and

weighing

kg (3Slbs).

allows

the

monitor

tilt

and swivel ±lSo, roll ± 90°, raise

and lower 2 in.

cm) and

the

arm extends 12 in. (30 cm).

r-------------

WARNING

---------------.

This

product

contains small items

that

could be a

choking

hazard

swallowed.

Keep these

items

away

from

young

children!

r-------------A.

CAUTION

--------------,

not

use this

product

for

any purpose

not

explicitly specified by Sanus Systems.

Improper installation or use may cause personal

injury

and/or

property

damage.

you

not

understand these instructions,

you have

doubts

about

the

safety

the

installation, contact Sanus Systems Customer Service. Sanus Systems

not

liable

for

injury

or damage caused by incorrect installation or

use.

Hardware and procedures

for

multiple

mounting

configurations are included.

OPT When you

see

this symbol, choose

the

correct configuration

suit your

needs.

Not

all hardware included will be used.

Sanus Systems

2221

Hwy

36 West, St Paul, MN 55113

USA

Customer

Service 1-800-359-5520· www.sanus.com

Summary of content (7 pages)

PAGE 1
SANUS SYSTEIVIS MOllS 6901-100054 <02> Thank you for choosing the Sanus Systems MOllS Desk Mount. The Sanus Systems MOllS Desk Mount is designed to support monitors sized up to 30 in. (76 cm) and weighing up to 15 kg (3Slbs). It allows the monitor to tilt and swivel ±lSo, roll ± 90°, raise and lower 2 in. (S cm) and the arm extends 12 in. (30 cm). r - - - - - - - - - - - - - A. WARNING - - - - - - - - - - - - - - - . This product contains small items that could be a choking hazard if swallowed.
PAGE 2
Supplied Parts and Hardware Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the item to your dealer; contact Sanus Systems Customer Service.
PAGE 3
1: Attach Pillar to Desk 2: Adjust Height I I, , I, ....-------A. CAUTION-----, I Avoid potential injuries or property damage! Do not adjust height with monitor attached. 6901-100054 <02> 3 ,.... 0 ...., ,.... 0 ....
PAGE 4
3: Select Plate 75mm 100mm -8r------- 200mm NOTE For monitors with 1OOmm x 200mm or 200mm x 200mm hole spacing, you must remove the existing plate from the head assembly and replace it with plate [02].
PAGE 5
4: Attach Monitor Flat Back e --. ---:::--.::::.--- --.;:::::::::::::J --- -.;:::::::::::-- ~-- I [10],[11] i -- --- ~- ...... I \---- : I : I I : I : I I i: I I I I I ~ I I I - - _ ~~---=::------- ~l =:--J--V ~-- Curved Back or Obstruction For clarity, monitor is not shown. [08],[09] --- - -rv: -- ---------- : 1 II : --~\ _-~~-- ~ --.
PAGE 6
5: Cable Placement NOTE Leave slack in the cables to prevent added tension on the connectors. .....-~--[16] .......- - - [ 1 6 ] CSAV, Inc. and its affiliated oorporations and subsidiaries (oollectively, ·CSAV"), intend to make this manual accurate and oomplate. However, CSAV makes no claim that tha information oontained herein oovers aN details, oonditions, or variations. Nor does it provide for every possible oontingency in oonnection with the installation or use of this product.
PAGE 7