LLF122 INSTRUCTION MANUAL Para Español ver página 20 WE’RE HERE TO HELP Want to watch a video that shows how easy this DIY project will be? Watch it now at: SANUS.com/2849 Recommended placement Check it out at: SANUS.com/2850 Get it right the first time. HeightFinder™ shows you where to drill. Our US-based install experts are standing by to help.
CAUTION: IMPORTANT SAFETY INSTRUCTIONS PLEASE READ ENTIRE MANUAL PRIOR TO USE — SAVE THESE INSTRUCTIONS Please read through these instructions completely to be sure you’re comfortable with this easy install process. Check your TV owner’s manual to see if there are any special requirements for mounting your TV. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, contact Customer Service: 1-855-734-7805.
Wall Construction ONLY install on these acceptable wall types. CAUTION: wood studs Solid concrete or concrete block DO NOT install in drywall alone Drywall alone will NOT hold the weight of your TV Unsure ACCEPTABLE Concrete kit CMK1 is required [NOT INCLUDED] Call Customer Service ACCEPTABLE Call Customer Service: 1-855-734-7805 Tools Needed 1/2 in. (13 mm) Stud Finder Pencil Awl Level 7/32 in. (5.
Dimensions 3-D TV INTERFACE 23.62in 600mm MAX 7.87in 200mm MIN 15.75in 7.87in 400mm 200mm MAX MIN 9.00in 228.5mm 5.31in 135mm WALL IS ON TOP 7.62in 193.5mm 5.31in 135mm SIDE VIEW - EXTENSION/TILT TOP VIEW - SWIVEL 0.87in 22mm 35deg 35deg SIMULATED 70" FLAT SCREEN TV 0.35in 9mm FRONT VIEW - TILT FULLY ASSEMBLED MOUNT 25.91in 658mm 15deg DOWN WALL IS ON RIGHT 15.98in 406mm 22.00in 558.8mm SIDE VIEW - RETRACTED WALL IS ON TOP 9.24in 234.6mm 17.13in 435mm 7.89in 200.
Supplied Parts and Hardware WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts! NOTE: Not all hardware included will be used. STEP 1 Parts and Hardware 01 TV Screws Washer (qty. 4 each) (qty.
STEP 3 Hardware STEP 2 Parts and Hardware M5 x 8mm Securement Screw 11 Wall Plate Template 07 Wall Plate Assembly qty. 1 08 qty. 1 Washer [Securement Screw] qty. 1 12 qty. 1 Installation / Adjustments Hex Key 13 Lag Screw 09 qty. 4 5/16 x 2¾ in. qty. 4 14 5/16 in. 6 M4 Cable Tie Washer [Lag Screw] 10 qty. 1 qty.
Hardware for STEP 2B Concrete Installation [Concrete Kit CMK1 is NOT INCLUDED] For concrete installations ONLY CAUTION: Do not use in drywall or wood Contact Customer Service to inquire about the ConcreteConcrete Installation Kit CMK1. Anchors For concrete installations ONLY CAUTIONFischer : Do not use in drywall or wood UX10 x 60R Concrete Anchors For concrete installations ONLY CAUTION: Do not use in drywall or wood Washer Concrete Anchors C2 C1 qty. 4 qty. 4 Fischer UX10 x 60R 5/16 in.
STEP 1 Attach TV Bracket to TV 1-1 Select TV Screw Diameter Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter (M6, or M8) to use. M6 M8 1-2 Select TV Screw Length a: For flat-back TVs, b: Spacers 03 supplied for: no spacers 03 required. a ●● Round (irregular) back TVs ●● Extra space needed (for cables or inset mounting holes) b FLAT BACK ROUND BACK CAUTION: Verify adequate thread engagement with the screw or screw/spacer combination.
1-3 Attach TV Bracket 1 2 3 H HEIGHT (H) greater than (>) 200 mm H mm inches cm mm 7⅞ 11 ¾ 15 ¾ 23 ¾ 20 30 40 60 200 300 400 600 HEIGHT (H) equal (=) 200 mm inch dimensions are approximate Measure the HEIGHT (H) of your TV's mounting hole pattern. NOTE: Position the slotted holes as shown for your TV hole pattern Height (H).
4 05 For HEIGHT (H) equal (=) 200 mm Screw posts on horizontal TV bracket 05 must sit in bottom hole of vertical TV bracket 04 . 5 F TV TOP O 04 05 04 05 Screw posts Angle the brackets 05 to clear the screw posts. Tilt the brackets 05 to nest the screw posts. Slide horizontal TV brackets 05 onto the vertical TV bracket 04 as shown. 10 05 04 TV HOLE PATTERN Center the TV brackets 04 and 05 over the hole pattern on your TV.
7 6 a: Flat Back 02 01 05 04 b: Round Back / Extra Space 03 02 01 05 06 06 Secure the assembly with the four wing nuts 06 . Center the TV bracket assembly over your TV's hole pattern and attach using screw combination a or b you selected for your TV. CAUTION: Avoid potential personal injuries and property damage! DO NOT use power tools for this step. Tighten the screws 01 only enough to secure the TV brackets to the TV.
STEP 2A Attach Wall Plate Wood Stud Installation CAUTION: Avoid potential personal injury or property damage! ●● ●● ●● ●● 1 Drywall covering the wall must not exceed 5/8 in. (16 mm) Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1 ½ x 3 ½ in. (38 x 89 mm) Minimum horizontal space between fasteners: 16 in. (406 mm) Stud centers must be verified MAX 5/8 in. (16 mm) 2 MIN. 16 in. (406 mm) 07 Locate studs.
3 2¾ in. (70 mm) 4 10 09 7/32 in. (5.5 mm) 07 Drill pilot holes then remove the wall plate template 07 . IMPORTANT: Be sure to drill into the center of the stud. IMPORTANT: Pilot holes must be drilled to a depth of 2 ¾ in. (70 mm), using a 7/32 in. (5.5 mm) diameter drill bit. 08 Install the wall plate 08 using four lag bolts 09 and washers 10 . Tighten all lag bolts only until they are pulled firmly against the wall plate. CAUTION: Improper use could reduce the holding power of the lag bolt.
STEP 2B Attach Wall Plate Solid Concrete or Concrete Block Installation CAUTION: Avoid potential personal injury or property damage! ●● ●● ●● ●● Mount the wall plate assembly 08 directly onto the concrete surface Minimum solid concrete thickness: 8 in. (203 mm) Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm) Minimum horizontal space between fasteners: 16 in.
4 3 C3 C2 08 C1 Remove wall plate template 07 and insert four concrete Install the wall plate 08 using four lag bolts C3 and anchors C1 . washers C2 . Tighten all lag bolts only until they are pulled firmly against the wall plate. CAUTION: Be sure the anchors are seated flush with the concrete surface. CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
STEP 3 Hang TV onto Wall Plate HEAVY! You may need assistance with this step. 1 2 04 08 Hang your TV onto the arm of wall plate assembly 08 by first hooking the top support, then resting the TV into place. 16 12 11 Lock TV to wall plate assembly 08 with screw 11 and washer 12 . CAUTION! Avoid potential personal injuries and property damage!Screw 11 must be installed to secure your TV onto the wall plate assembly 08 .
Manage Cables Fully extend the arms before routing cables. Use cable ties 14 to bundle and attach cables to the arms 08 for a cleaner look.
TV Adjustments TILT LEVEL 1. Loosen the tilt lever 2. Adjust the TV tilt position. 3. Tighten tilt lever T T . to secure the TV in place at your desired tilt angle. NOTE: If needed, tighten screw T2 for additional tilt tensioning. T2 08 1. Loosen the screw 11 on the rear of wall plate assembly 08 . 2. Level your TV. 3. Retighten screw 11 to secure in place.
REMOVING THE TV HEAVY! You may need assistance with this step. To remove your TV from the wall plate assembly 08 : 1. 2. 3. Disconnect all cables. Remove screw 11 and washer 12 . Lift the TV up and off of wall plate assembly 08 .
ESPAÑOL INSTRUCCIONES IMPORTANTES DE SEGURIDAD - LEA TODO ESTE MANUAL ANTES DE UTILIZAR ESTE PRODUCTO - GUARDE ESTAS INSTRUCCIONES Lea atentamente estas instrucciones en su totalidad para asegurarse de que está familiarizado con el sencillo proceso de instalación. Consulte igualmente el manual de su televisor para conocer si existen requisitos especiales para el montaje de su aparato.
Dimensiones Consulte la página 4 Piezas y elementos de sujeción suministrados Consulte la página 5 ESPAÑOL ADVERTENCIA: Este producto contiene piezas pequeñas que, en caso de ser tragadas, podrían causar asfixia. Antes de comenzar a montar la unidad, verifique que dispone de todas las piezas y que se encuentran en buen estado. Si no dispone de todas las piezas o alguna está dañada, no devuelva el elemento defectuoso al distribuidor. Póngase en contacto con el Servicio de Atención al Cliente.
ESPAÑOL PASO 2A Fijar la placa de pared a la pared - Montante de madera ●● ●● ●● ●● 1. 2. 3. 4. Consulte la página 12 PRECAUCIÓN: Evite posibles lesiones personales y daños materiales. Los paneles de yeso sobre la pared no deben ser mayores de 16 mm (5/8 pulg.) Tamaño mínimo de los montantes de madera: nominal 51 x 102 mm (2 x 4 pulg.) actual 38 x 89 mm (1½ x 3½ pulg.) Espacio horizontal mínimo entre los elementos de sujeción: 406 mm (16'') Se debe verificar el centro del montante Localice el montante.
ESPAÑOL PASO 3 Colgar el televisor en la placa de pared Consulte la página 16 ¡PRODUCTO PESADO! Podría necesitar ayuda para realizar esta operación. 1. Cuelgue el televisor en el brazo del conjunto de placa de pared 2. Bloquee el televisor en el conjunto de placa de pared PRECAUCIÓN: Este tornillo 11 08 08 enganchando en primer lugar el apoyo superior y luego dejando caer el televisor en su posición. con el tornillo 11 y la arandela 12 .
Watch the installation video or call our Customer Care team for help SAN.US/2849 1-855-734-7805 Legrand AV Inc. and its affiliated corporations and subsidiaries (collectively, “Legrand”), intend to make this manual accurate and complete. However, Legrand makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product.