DT-120 / DT-180V GB Version 1
1
Controls 1 2 3 4 5 6 7 8 9 10 11 LCD display Band selection DBB (Deep Bass Booster) On/Off Tuning Control Stereo/Mono switch Power On/Off Volume Control Lock Switch Battery Compartment Memory button Earphone Jack Display A B C D E F G Selected Band System lock FM stereo indicator Battery power indicator Memory presets DBB on Frequency GB 2
Battery Installation Battery cover is located on the back of the unit. Slide the cover in the direction of the arrow to gain access to the battery compartment. Insert one AAA (UM-4) battery into the compartment. Make sure that the battery is positioned in accordance with the indicated diagram. Replace cover. Note: 1. You can always monitor the battery power from LCD display battery icon.
Antenna/Earphone Insert the earphone into the earphone jack. The cord connecting the earphone to the receiver acts as an antenna during FM and TV (DT-180V) audio reception and should be extended as much as possible to increase the sensitivity. A built-in ferrite bar antenna is provided for AM reception and it is only necessary to rotate the radio for maximum signal strength during AM listening.
Volume Control Using the volume control knobs to adjust volume level. Display will show the changes when you operate the volume control. Tuning the radio Band: AM Frequency: DT-120 522 - 1629 kHz (9 kHz) DT-120 520 - 1710 kHz (10 kHz) DT-180V 522 - 1629 kHz (9 kHz) DT-180V 520 - 1710 kHz (10 kHz) Antenna: Internal/Rotate radio for bes reception Band: FM Frequency: 87.
Band: TV Frequency: TV channels 2-13 (DT-180V) Antenna: External/Make sure the earphone is plugged into earphone jack Scan Tuning Turn on the radio, select required band by pressing Band Selection button. Press and hold down the Tuning Control buttons for more than half a second and release the button to commence Scan Tuning. The radio will scan and stop automatically when a station is found.
Manual tuning Turn on the radio, select required band by pressing Band Selection button. Desired station may be selected by pressing the Tuning Control buttons intermittently until the desired station is reached. Or pressing and holding the Tuning Control until the desired station is reached. Memory Tuning (Station Preset) Turn on the radio by pressing Power On/Off button. Select required band by pressing Band Selection button. Tune to the desired station using the Scan or Manual tuning described above.
You may store 5 memory stations each band (AM, FMI, FMII and TV). Recall memory stations Turn on the radio, select required band then simply press and release Memory station button. LCD display will show Memory preset and radio frequency. Stereo/Mono switch The radio is designed to receive FM stereo broadcastings. For weak FM station, switch Stereo/Mono to Mono position. LCD display Stereo icon will disappear.
Change AM band tuning step For Northern American countries and some South American countries, AM tuning step is 10 kHz. On other countries is 9 kHz. To change AM band tuning step, please follow below steps. 1. Change the AM band tuning step from 9 kHz to 10 kHz When radio is OFF, press and hold Tuning UP button then switch on radio by pressing Power On/Off button until LCD display flashes 10 and then 520, indicating AM step has been changed to 10 kHz tuning step. 2.
Note: To change AM step will erase all the AM Memory preset stations. System Lock To prevent accidental changing of any of the radio settings. Switch the Lock switch to Lock position. LCD display lock icon will appear. To release, simply switch the Lock switch to its opposite position, LCD display lock icon will disappear. It’s important to make sure Lock switch is in its off position when radio is to be operated, as radio is completely inoperative until Lock Switch is released.
Specifications Battery: 1 x AAA (LR03, UM-4) Frequency Coverage: FM: 87.50 – 108 MHz AM: 522 – 1629 kHz ( DT-120 9 kHz) 520 – 1710 kHz ( DT-120 10 kHz) 522 – 1629 kHz (DT-180V 9 kHz) 520 – 1710 kHz (DT-180V 10 kHz) TV: 2 – 13 channel (DT-180V) Output Power: 1.0 mW + 1.0 mW Earphone Jack: 3.5 mm diameter (stereo) The company reserves the right to amend the specifications without notice.
