CompactFlash™ Memory Card Product Manual (Preliminary) ® CORPORATE HEADQUARTERS 140 Caspian Court Sunnyvale, CA 94089 408-542-0500 FAX: 408-542-0503 URL: http://www.sandisk.
SanDisk® Corporation general policy does not recommend the use of its products in life support applications where in a failure or malfunction of the product may directly threaten life or injury. Per SanDisk Terms and Conditions of Sale, the user of SanDisk products in life support applications assumes all risk of such use and indemnifies SanDisk against all damages. The information in this manual is subject to change without notice.
Preliminary CompactFlash Memory Card Product Manual Table of Contents 1.0 Introduction to the CompactFlash Memory Card ...................................................................7 1.1 1.2 1.3 1.4 1.5 1.6 1.7 2.0 Product Specifications ..........................................................................................................12 2.1 2.2 2.3 2.4 2.5 2.6 3.0 System Environmental Specifications .........................................................................................
CompactFlash Memory Card Product Manual Table of Contents 4.4 4.5 4.6 4.7 5.0 Card Configuration.............................................................................................................................36 4.4.1 Attribute Memory Function ................................................................................................37 4.4.2 Configuration Option Register (Address 200h in Attribute Memory) ..........................38 4.4.
Preliminary Table of Contents 6.2 7.0 CompactFlash Memory Card Product Manual (continued) 6.1.5.9 Buffer Type ..........................................................................................................61 6.1.5.10 Buffer Size ............................................................................................................61 6.1.5.11 ECC Count ...........................................................................................................61 6.1.5.
CompactFlash Memory Card Product Manual Table of Contents Preliminary (continued) Ordering Information and Technical Support................................................................................97 Ordering Information....................................................................................................................................99 CompactFlash Memory Card ............................................................................................................
Preliminary CompactFlash Memory Card Product Manual 1.0 Introduction to the CompactFlash Memory Card The SanDisk CompactFlash™ Memory Card (CF™) products provide high capacity solid state flash memory that electrically complies with the Personal Computer Memory Card International Association ATA (PC Card ATA) standard. (In Japan, the applicable standards group is JEIDA.) The CompactFlash Memory Card Series also supports a True IDE Mode that is electrically compatible with an IDE disk drive.
CompactFlash Memory Card Product Manual Preliminary Data In/O ut Host Interface SanDisk Single Chip Controller SanDisk Flash Modules Control SanDisk CompactFlash Figure 1-1 CompactFlash Memory Card Block Diagram 1.1 Scope 1.2 This document describes the key features and specifications of CompactFlash Memory Cards, as well as the information required to interface this product to a host system.
Preliminary 1.3 • • • • • • • • • • • • • • • • 1.4 CompactFlash Memory Card Product Manual System Features 1.5 Up to 512 MBytes of mass storage data PC Card ATA protocol compatible True IDE Mode compatible Very low CMOS power Very high performance Very rugged Low weight Noiseless Low Profile +5 Volts or +3.
CompactFlash Memory Card Product Manual 1.7.1 Flash Technology Independence The 512 byte sector size of the CompactFlash Memory Card is the same as that in an IDE magnetic disk drive. To write or read a sector (or multiple sectors), the host computer software simply issues a Read or Write command to the CompactFlash Memory Card. This command contains the address and the number of sectors to write/read. The host software then waits for the command to complete.
Preliminary 1.7.5 CompactFlash Memory Card Product Manual Automatic Sleep Mode A unique feature of the SanDisk CompactFlash Memory Card (and other SanDisk products) is automatic entrance and exit from sleep mode. Upon completion of a command, the CompactFlash Card will enter sleep mode to conserve power if no further commands are received within 5 msec. The host does not have to take any action for this to occur.
CompactFlash Memory Card Product Manual Preliminary 2.0 Product Specifications For all the following specifications, values are defined at ambient temperature and nominal supply voltage unless otherwise stated. 2.
Preliminary 2.3 CompactFlash Memory Card Product Manual System Performance All performance timings assume the CompactFlash Memory Card Series controller is in the default (i.e., fastest) mode. Start Up Times Sleep to write: Sleep to read: Reset to ready: Active to Sleep Delay 2.5 msec maximum 2.0 msec maximum 50 msec typical 400 msec maximum Programmable Data Transfer Rate To/From Flash 20.0 MBytes/sec burst Data Transfer Rate To/From Host 16.
CompactFlash Memory Card Product Manual 2.5 Preliminary Physical Specifications Refer to the following table and to Figure 2-1 for CompactFlash Memory Card physical specifications and dimensions. CompactFlash Weight: 11.4 g (.40 oz) typical 14.2 g (.50 oz) maximum Length: 36.40 ± 0.15 mm (1.433 ±.006 in) Width: 42.80 ± 0.10 mm (1.685 ±.004 in) Thickness: 3.3 mm ± 0.10 mm (.130 ±.004 in) (Excluding Lip) .039±.002 [1.00] 25 .040±.003 [1.00] 2X .118±.003 [3.00] P TO .096±.003 [2.4] [36.40] 1 .040±.
Preliminary CompactFlash Memory Card Product Manual Refer to the following table and to Figure 2-2 for CompactFlash Memory Card PC Card Adapter physical specifications and dimensions. CF Adapter Weight: 33 g (1.16 oz) typical Length: 85.6 ± 0.20 mm (3.370 ±.008 in) Width: 54.0 ± 0.10 mm (2.126 ±.004 in) Thickness: 5.0 mm Max (0.1968 in) 0.196 [5.0] 0.130 [3.3] 2.126 [54.0] 3.370 [85.6] 1.196 [30.4] .866 [22.0] 1.536 [39.03] .472 [12.0] .078 [2.0] 1.694 [43.03] 0.138 [3.
CompactFlash Memory Card Product Manual 2.6 Preliminary Capacity Specifications The table below shows the specific capacity for the various models and the default number of heads, sectors/track and cylinders. 16 Model Number Capacity (formatted) Sectors/Card (Max LBA+1) No. of Heads No. of Sectors/ Track No.
Preliminary CompactFlash Memory Card Product Manual 3.0 Installation 3.1 Mounting The CompactFlash Memory Card may be installed in any platform with a 50 position Surface Mount Interface Header (3M P/N N7E50-7516VY-20) and Ejector (3M P/N D7E50-7316-02), or equivalent, properly installed. Refer to the appendix at the end of this manual for additional technical information. In addition, the CompactFlash Memory Card may be used in any standard PCMCIA Type II (5 mm) or Type III (10.
CompactFlash Memory Card Product Manual Preliminary 4.0 CompactFlash Memory Card Interface Description 4.1 Physical Description The host is connected to the CompactFlash Memory Card using a standard 50 pin connector consisting of two rows of 25 female contacts each on 50 mil (1.27 mm) centers. 4.1.1 Pin Assignments and Pin Type The signal/pin assignments are listed in Table 4-1. Low active signals have a “-” prefix. Pin types are Input, Output or Input/Output.
Preliminary CompactFlash Memory Card Product Manual Table 4-1 Pin Assignments and Pin Type PC Card Memory Mode Pin Num Signal Name 1 GND 2 D03 3 PC Card I/O Mode 4 True IDE Mode 4 Pin Num Signal Name Ground 1 GND I/O I1Z,OZ3 2 D03 I/O I1Z,OZ3 D04 I/O I1Z,OZ3 3 D04 I/O I1Z,OZ3 4 D05 I/O I1Z,OZ3 4 D05 I/O I1Z,OZ3 I1Z,OZ3 5 D06 I/O I1Z,OZ3 5 D06 I/O I1Z,OZ3 I/O I1Z,OZ3 6 D07 I/O I1Z,OZ3 6 D07 I/O I1Z,OZ3 I I3U 7 -CE1 I I3U 7 -CS0 I I3Z 2 In, Ou
CompactFlash Memory Card Product Manual Preliminary Table 4-1 Pin Assignments and Pin Type (continued) PC Card Memory Mode PC Card I/O Mode True IDE Mode Pin Num Signal Name Pin Type In, Out Type Pin Num Signal Name Pin Type In, Out Type Pin Num Signal Name Pin Type In, Out4 Type 35 -IOWR I I3U 35 -IOWR I I3U 35 -IOWR I I3Z 36 -WE I I3U 36 -WE I I3U 36 -WE3 I I3U 37 RDY/BSY O OT1 37 IREQ O OT1 37 INTRQ O OZ1 38 VCC Power 38 VCC Power 38 VCC 39 -C
Preliminary CompactFlash Memory Card Product Manual Table 4-2 Signal Description Signal Name Dir. A10 - A0 (PC Card Memory Mode) I Pin 8, 10, 11, 12, 14, These address lines along with the -REG signal are used to select the following: The I/O port address registers within the CompactFlash 15, 16, 17, 18, Card, the memory mapped port address registers within the card, a 19, 20 byte in the card's information structure and its configuration control and status registers.
CompactFlash Memory Card Product Manual Preliminary Table 4-2 Signal Description (continued) Signal Name Dir. Pin Description -CSEL (PC Card Memory Mode) I 39 This signal is not used for this mode. -CSEL (PC Card I/O Mode) This signal is not used for this mode. -CSEL (True IDE Mode) This internally pulled up signal is used to configure this device as a Master or a Slave when configured in the True IDE Mode. When this pin is grounded, this device is configured as a Master.
Preliminary CompactFlash Memory Card Product Manual Table 4-2 Signal Description (continued) Signal Name Dir. Pin Description -IOWR (PC Card Memory Mode) I 35 This signal is not used in this mode. -IOWR (PC Card I/O Mode) The I/O Write strobe pulse is used to clock I/O data on the Card Data bus into the CompactFlash controller registers when the card is configured to use the I/O interface. The clocking will occur on the negative to positive edge of the signal (trailing edge).
CompactFlash Memory Card Product Manual Preliminary Table 4-2 Signal Description (continued) Signal Name Dir. Pin Description RESET (PC Card Memory Mode) I 41 When the pin is high, this signal resets the CompactFlash Card. The card is Reset only at power up if this pin is left high or open from power-up. The card is also reset when the Soft Reset bit in the Card Configuration Option Register is set. RESET (PC Card I/O Mode) This signal is the same as the PC Card Memory Mode signal.
Preliminary 4.3 CompactFlash Memory Card Product Manual Electrical Specification Absolute Maximum conditions are: The following table defines all D.C. Characteristics for the CompactFlash Memory Card Series. Vcc = -0.3V min. to 7.0V max. V* = -0.5V min. to Vcc + 0.5V max. Unless otherwise stated, conditions are: * Voltage on any pin except Vcc with respect to GND. SDCFB-XX SDCFBI-XX Vcc = 5V ±10% Vcc = 5V ± 10% Vcc = 3.3V ± 5% Vcc = 3.3V ± 5% Ta = 0°C to 60°C Ta = -40°C to 85°C 4.3.
CompactFlash Memory Card Product Manual Preliminary 4.3.3 Output Drive Type Note: In the table below, x refers to the characteristics described in section 4.3.4. For example, OT3 refers to Totempole output with a type 3 output drive characteristic. Type Output Type OTx Totempole Ioh & Iol OZx Tri-State N-P Channel Ioh & Iol OPx P-Channel Only Ioh Only ONx N-Channel Only Iol Only 4.3.
Preliminary 4.3.5 CompactFlash Memory Card Product Manual Common Memory Read Timing There are several types of memory cards, SRAM, memory devices, read timing specifications are OTPROM, etc., and within a memory card, several common. types of memory devices may be mounted.
CompactFlash Memory Card Product Manual 4.3.6 Preliminary Common and Attribute Memory Write Timing The write timing specifications for Common and Attribute memory are the same.
Preliminary CompactFlash Memory Card Product Manual 4.3.6.1 Common Memory Write Timing The programming specification of various memory devices are not standardized. Moreover, programming specifications may vary among different generations of the same 4.3.7 device. Consequently, it is not practical to set standardized programming specifications for these memory devices. Attribute Memory Read Timing Specification The Attribute Memory’s access time is defined as 300 ns at 5 V Vcc or 600 ns at 3.3 Vcc.
CompactFlash Memory Card Product Manual 4.3.9 1. 2. 3. Preliminary Memory Timing diagrams Shaded areas may be high or low. Applies to card only when WAIT# is negated by card. However, the host shall always provide at least this access time before sampling data. Applies only when WAIT# is asserted by card. Figure 4-1 Read Timing Diagram 30 SanDisk CompactFlash Memory Card Product Manual Rev.
Preliminary CompactFlash Memory Card Product Manual tcW A[25::0], REG# tsu(CE-WEH) CE# tsu(CE) NOTE 1 NOTE 1 tsu(A-WEH) NOTE 4 NOTE 4 OE# tsu(A) WE# th(CE) NOTE 3 tv(WT) tv(WT-WE) tw(WT) WAIT# th(OE-WE) tsu(OE-WE) D[15::0](Din) tsu(D-WEH) DATA INPUT ESTABLISHED tdis(WE) 4. ten(OE) ten(WE) D[15::0](Dout) 3. th(D) NOTE 2 tdis(OE) 1. 2. trec(WE) tw(WE) Shaded areas may be high or low.
CompactFlash Memory Card Product Manual 4.3.10 Preliminary I/O Read (Input) Timing Specification A[25::0] thA(IORD) REG# CE# tsuREG(IORD) thREG(IORD) tsuCE(IORD) thCE(IORD) tw(IORD) IORD# tsuA(IORD) tdrINPACK(ADR) INPACK# tdfINPACK(IORD) tdrIOIS16(ADR) IOIS16#) tdfIOIS16(ADR) td(IORD) tdr(WT) WAIT# tdfWT(IORD) tw(WT) th(IORD) D[15::0] All timings are measured at the PC Card. Skews and delays from the host system driver/receiver to the PC Card must be accounted for by the system design.
Preliminary CompactFlash Memory Card Product Manual Table 4-6 I/O Read (Input) Timing Specification for All I/O Cards Item Symbol IEEE Symbol Min Max Data Delay after IORD# td(IORD) tlGLQV Data Hold following IORD# th(IORD) tlGHQX 0 IORD# Width Time tw(IORD) tlGLIGH 165 Address Setup before IORD# tsuA(IORD) tAVIGL 70 Address Hold following IORD# thA(IORD) tlGHAX 20 CE# Setup before IORD# tsuCE(IORD) tELIGL 5 CE# Hold following IORD# thCE(IORD) tlGHEH 20 REG# Setup before IO
CompactFlash Memory Card Product Manual 4.3.11 Preliminary I/O Write (Output) Timing Specification A[25::0] thA(IOWR) REG# tsuREG(IOWR) thREG(IOWR) tsuCE(IOWR) CE# thCE(IOWR) tw(IOWR) IOWR# tsuA(IOWR) tdrIOIS16(ADR) IOIS16#) tdfIOIS16(ADR) tdfWT(IOWR) tdrIOWR(WT) WAIT# tw(WT) th(IOWR) D[15::0] tsu(IOWR) All timings are measured at the PC Card. Skews and delays from the host system driver/receiver to the PC Card must be accounted for by the system design.
Preliminary CompactFlash Memory Card Product Manual Table 4-7 I/O Write Timing Specification for All I/O Cards Item Symbol IEEE Symbol Min Max Data Setup before IOWR# tsu(IOWR) tDVIWL 60 Data Hold following IOWR# th(IOWR) tlWHDX 30 IOWR# Width Time twIOWR tlWLIWH 165 Address Setup before IOWR# tsuA(IOWR) tAVIWL 70 Address Hold following IOWR# thA(IOWR) tlWHAX 20 CE# Setup before IOWR# tsuCE(IOWR) tELIWL 5 CE# Hold following IOWR# thCE(IOWR) tlWHEH 20 REG# Setup before IOWR
CompactFlash Memory Card Product Manual 4.4 Preliminary Card Configuration provide a method for accessing status information about the CompactFlash Card that may be used to arbitrate between multiple interrupt sources on the same interrupt level or to replace status information that appears on dedicated pins in memory cards that have alternate use in I/O cards. The CompactFlash Memory Cards are identified by appropriate information in the Card Information Structure (CIS).
Preliminary 4.4.1 CompactFlash Memory Card Product Manual Attribute Memory Function during the cycle. As in the Main Memory Read functions, the signals -CE1 and -CE2 control the even-byte and odd-byte address, but only the even-byte data is valid during the Attribute Memory access. Refer to Table 4-12 below for signal states and bus validity for the Attribute Memory function.
CompactFlash Memory Card Product Manual 4.4.2 Preliminary Configuration Option Register (Address 200h in Attribute Memory) The Configuration Option Register is used to configure the cards interface, address decoding and interrupt and to issue a soft reset to the CompactFlash Memory Card.
Preliminary CompactFlash Memory Card Product Manual Changed Indicates that one or both of the Pin Replacement register CRdy, or CWProt bits are set to one (1). When the Changed bit is set, -STSCHG Pin 46 is held low if the SigChg bit is a One (1) and the CompactFlash Memory Card is configured for the I/O interface. SigChg This bit is set and reset by the host to enable and disable a state-change “signal” from the Status Register, the Changed bit control pin 46 the Changed Status signal.
CompactFlash Memory Card Product Manual Preliminary Table 4-14 Pin Replacement Changed Bit/Mask Bit Values Initial Value 4.4.5 Written by Host Final Comments of (C) Status “C” Bit “M” Bit “C” Bit 0 X 0 0 Unchanged 1 X 0 1 Unchanged X 0 1 0 Cleared by Host X 1 1 1 Set by Host Socket and Copy Register (Address 206h in Attribute Memory) This register contains additional configuration information.
Preliminary CompactFlash Memory Card Product Manual 4.5 I/O Transfer Function 4.5.1 I/O Function CompactFlash Card permits both 8 and 16 bit accesses to all of its I/O addresses, so -IOIS16 is asserted for all addresses to which the CompactFlash Card responds. The I/O transfer to or from the CompactFlash Memory Card can be either 8 or 16 bits. When a 16-bit accessible port is addressed, the signal -IOIS16 is asserted by the CompactFlash Card. Otherwise, the -IOIS16 signal is de-asserted.
CompactFlash Memory Card Product Manual 4.6 Common Memory Transfer Function 4.6.1 Common Memory Function Preliminary The CompactFlash Memory Card may request the host to extend the length of a memory write cycle or extend the length of a memory read cycle until data is ready by asserting the -WAIT signal at the start of the cycle. The Common Memory transfer to or from the CompactFlash Memory Card can be either 8 or 16 bits.
Preliminary CompactFlash Memory Card Product Manual 4.7 True IDE Mode I/O Transfer Function 4.7.1 True IDE Mode I/O Function The CompactFlash Memory Card can be configured in a True IDE Mode of operation. This CompactFlash Card is configured in this mode only when the -OE input signal is grounded by the host. In this True IDE Mode, the PCMCIA protocol and configuration are disabled and only I/O operations to the Task File and Data Register are allowed.
CompactFlash Memory Card Product Manual Preliminary 5.0 ATA Drive Register Set Definition and Protocol The CompactFlash Memory Card can be configured as a high performance I/O device through: a.) Standard PC-AT disk I/O address spaces 1F0h1F7h, 3F6h-3F7h (primary); 170h-177h, 376h377h (secondary) with IRQ 14 (or other available IRQ). The communication to or from the CompactFlash Memory Card is done using the Task File registers which provide all the necessary registers for control and status information.
Preliminary 5.1 CompactFlash Memory Card Product Manual I/O Primary and Secondary Address Configurations Table 5-2 Primary and Secondary I/O Decoding Notes: -REG A9-A4 A3 A2 A1 A0 -IORD=0 -IOWR=0 Note 0 1F(17) 0 0 0 0 Even RD Data Even WR Data 1, 2 0 1F(17) 0 0 0 1 Error Register Features 1 0 1F(17) 0 0 1 0 Sector Count Sector Count 0 1F(17) 0 0 1 1 Sector No. Sector No.
CompactFlash Memory Card Product Manual 5.
Preliminary 5.
CompactFlash Memory Card Product Manual 5.4 Preliminary True IDE Mode Addressing When the CompactFlash Memory Card is configured in the True IDE Mode the I/O decoding is as follows: Table 5-5 True IDE Mode I/O Decoding 48 -CE2 -CE1 A2 A1 A0 -IORD=0 -IOWR=0 1 0 0 0 0 Even RD Data Even WR Data 1 0 0 0 1 Error Register Features 1 0 0 1 0 Sector Count Sector Count 1 0 0 1 1 Sector No. Sector No.
Preliminary CompactFlash Memory Card Product Manual 5.5 ATA Registers Note: In accordance with the PCMCIA specification: each of the registers below which is located at an odd offset address may be accessed at its normal address and also the corresponding even address (normal address -1) using data bus lines (D15-D8) when CE1 is high and -CE2 is low unless -IOIS16 is high (not asserted) and an I/O cycle is being performed. 5.5.
CompactFlash Memory Card Product Manual 5.5.2 Preliminary Error Register (Address - 1F1[171]; Offset 1, 0Dh Read Only) This register contains additional information about the source of an error when an error is indicated in bit 0 of the Status register. The bits are defined as follows: D7 D6 D5 D4 D3 D2 D1 D0 BBK UNC 0 IDNF 0 ABRT 0 AMNF This register is also accessed on data bits D15-D8 during a write operation to offset 0 with -CE2 low and -CE1 high.
Preliminary 5.5.8 CompactFlash Memory Card Product Manual Drive/Head (LBA 27-24) Register (Address 1F6[176]; Offset 6) The Drive/Head register is used to select the drive and head. It is also used to select LBA addressing instead of cylinder/head/sector addressing. The bits are defined as follows: D7 D6 D5 D4 D3 D2 D1 D0 1 LBA 1 DRV HS3 HS2 HS1 HS0 Bit 7 Bit 6 Bit 5 Bit 4 (DRV) Bit 3 (HS3) Bit 2 (HS2) Bit 1 (HS1) Bit 0 (HS0) This bit is set to 1.
CompactFlash Memory Card Product Manual 5.5.9 Status & Alternate Status Registers (Address 1F7[177]&3F6[376]; Offsets 7 & Eh) These registers return the CompactFlash Memory Card status when read by the host. Reading the Status register does clear a pending interrupt while reading the Auxiliary Status register does not.
Preliminary 5.5.10 CompactFlash Memory Card Product Manual Device Control Register (Address - 3F6[376]; Offset Eh) This register is used to control the CompactFlash Memory Card interrupt request and to issue an D7 D6 D5 D4 D3 D2 D1 D0 X X X X 1 SW Rst -IEn 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 (SW Rst) Bit 1 (-IEn) Bit 0 ATA soft reset to the card. The bits are defined as follows: This bit is an X (don't care). This bit is an X (don't care). This bit is an X (don't care).
CompactFlash Memory Card Product Manual 5.5.11 Preliminary Card (Drive) Address Register (Address 3F7[377]; Offset Fh) This register is provided for compatibility with the AT disk drive interface. It is recommended that this register not be mapped into the host's I/O space because of potential conflicts on Bit 7.
Preliminary 6.0 CompactFlash Memory Card Product Manual ATA Command Description This section defines the software requirements and the format of the commands the host sends to the CompactFlash Memory Cards. Commands are issued to the CompactFlash Card by loading the required registers in the command block with the supplied parameters, and then writing the command code to the Command Register. The manner in which a command is accepted varies.
CompactFlash Memory Card Product Manual Preliminary Table 6-1 ATA Command Set Class COMMAND Code FR SC SN CY DH LBA 1 Check Power Mode E5h or 98h - - - - D - 1 Execute Drive Diagnostic 90h - - - - D - 1 Erase Sector(s) (Note 2) C0h - Y Y Y Y Y 2 Format Track 50h - Y - Y Y Y 1 Identify Drive ECh - - - - D - 1 Idle E3h or 97h - Y - - D - 1 Idle Immediate E1h or 95h - - - - D - 1 Initialize Drive Parameters 91h - Y - - Y - 1 Re
Preliminary 6.1.1 CompactFlash Memory Card Product Manual Check Power Mode - 98H, E5H Bit -> 7 6 5 4 2 1 0 E5H or 98H Command (7) X C/D/H (6) Drive X Cyl High (5) X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) X Feature (1) X If the CompactFlash Memory Card is in Idle mode, the CompactFlash Card sets BSY, sets the Sector Count Register to FFh, clears BSY and generates an interrupt. This command checks the power mode.
CompactFlash Memory Card Product Manual Preliminary Table 6-2 Diagnostic Codes 6.1.
Preliminary 6.1.4 CompactFlash Memory Card Product Manual Format Track - 50H Bit -> 7 6 5 4 3 1 LBA 1 Drive 0 Head (LBA 27-24) Cyl High (5) Cylinder High (LBA 23-16) Cyl Low (4) Cylinder Low (LBA 15-8) Sec Num (3) X (LBA 7-0) Sec Cnt (2) Count (LBA mode only) Feature (1) X command with the same protocol as the Write Sector(s) command although the information in the buffer is not used by the CompactFlash Card.
CompactFlash Memory Card Product Manual Preliminary Table 6-3 Identify Drive Information 60 Word Address Default Value Total Bytes Data Field Type Information 0 848AH 2 General configuration bit-significant information 1 XXXX 2 Default number of cylinders 2 0000H 2 Reserved 3 XXXX 2 Default number of heads 4 0000H 2 Number of unformatted bytes per track 5 0240H 2 Number of unformatted bytes per sector 6 XXXX 2 Default number of sectors per track 7-8 XXXX 4 Number of se
Preliminary CompactFlash Memory Card Product Manual 6.1.5.1 Word 0: General Configuration 6.1.5.7 Words 7-8: Number of Sectors per Card This field informs the host that this is a non-magnetic, hard sectored, removable storage device with a transfer rate greater than 10 mb/sec and is not MFM encoded. This field contains the number of sectors per CompactFlash Memory Card. This double word value is also the first invalid address in LBA translation mode. 6.1.5.2 Word 1: Default Number of Cylinders 6.1.5.
CompactFlash Memory Card Product Manual Preliminary 6.1.5.14 Word 47: Read/Write Multiple Sector Count 6.1.5.22 Word 59: Multiple Sector Setting This field contains the maximum number of sectors that can be read or written per interrupt using the Read Multiple or Write Multiple commands. This field contains a validity flag in the odd byte and the current number of sectors that can be transferred per interrupt for R/W Multiple in the even byte.
Preliminary 6.1.6 CompactFlash Memory Card Product Manual Idle - 97H, E3H Bit -> 7 6 5 4 3 X C/D/H (6) Drive 0 X Cyl High (5) X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) Timer Count (5 msec increments) Feature (1) X enabled. If the sector count is zero, the automatic power down mode is disabled. Note that this time base (5 msec) is different from the ATA specification.
CompactFlash Memory Card Product Manual 6.1.8 Initialize Drive Parameters - 91H Bit -> 7 6 5 4 3 C/D/H (6) 2 1 0 91H Command (7) X 0 X Drive Max Head (no. of heads-1) Cyl High (5) X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) Number of Sectors Feature (1) X Note: This command enables the host to set the number of sectors per track and the number of heads per cylinder. Only the Sector Count and the Card/Drive/Head registers are used by this command. 6.1.
Preliminary 6.1.10 CompactFlash Memory Card Product Manual Read Multiple - C4H Bit -> 7 6 5 4 3 Note: 1 0 C4H Command (7) C/D/H (6) 2 1 LBA 1 Drive Head (LBA 27-24) Cyl High (5) Cylinder High (LBA 23-16) Cyl Low (4) Cylinder Low (LBA 15-8) Sec Num (3) Sector Number (LBA 7-0) Sec Cnt (2) Sector Count Feature (1) X The current revision of the CompactFlash Memory Card only supports a block count of 1 as indicated in the Identify Drive Information command.
CompactFlash Memory Card Product Manual 6.1.11 Read Long Sector - 22H, 23H Bit -> 7 6 5 4 C/D/H (6) 3 1 LBA 1 Drive Cylinder High (LBA 23-16) Cyl Low (4) Cylinder Low (LBA 15-8) Sec Num (3) Sector Number (LBA 7-0) Sec Cnt (2) X Feature (1) X 0 transferred in word mode followed by 4 bytes of random data transferred in byte mode. Random data is returned instead of ECC bytes because of the nature of the ECC system used. This command has the same protocol as the Read Sector(s) command.
Preliminary 6.1.13 CompactFlash Memory Card Product Manual Read Verify Sector(s) - 40H, 41H Bit -> 7 6 5 4 1 LBA 1 Drive Cylinder High (LBA 23-16) Cyl Low (4) Cylinder Low (LBA 15-8) Sec Num (3) Sector Number (LBA 7-0) Sec Cnt (2) Sector Count Feature (1) X 0 the cylinder, head, and sector number of the last sector verified. This command is identical to the Read Sectors command, except that DRQ is never set and no data is transferred to the host.
CompactFlash Memory Card Product Manual 6.1.15 Preliminary Request Sense - 03H Bit -> 7 6 5 4 3 1 0 03H Command (7) C/D/H (6) 2 1 X 1 Drive X Cyl High (5) X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) X Feature (1) X This command requests an extended error code after a command ends with an error. Table 6-4 defines the valid extended error codes for the CompactFlash Memory Card Series product. The extended error code is returned to the host in the Error Register.
Preliminary 6.1.16 CompactFlash Memory Card Product Manual Seek - 7XH Bit -> 7 6 5 4 3 1 LBA 1 Drive Cylinder High (LBA 23-16) Cyl Low (4) Cylinder Low (LBA 15-8) Sec Num (3) X (LBA 7-0) Sec Cnt (2) X Feature (1) X This command is effectively a NOP command to the CompactFlash Memory Card although it does perform a range check of cylinder and head or LBA 6.1.17 Set Features - EFH 7 6 5 address and returns an error if the address is out of range.
CompactFlash Memory Card Product Manual Preliminary Table 6-5 Features Supported Feature Operation 01H Enable 8 bit data transfer. 55H Disable Read Look Ahead. 66H Disable Power on Reset (POR) establishment of defaults at Soft Reset. 69H Accepted for backward compatibility with the SDP Series but has no impact on the CF Memory Card. 81H Disable 8 bit data transfer. 96H Accepted for backward compatibility with the SDP Series but has no impact on the CF Memory Card.
Preliminary 6.1.18 CompactFlash Memory Card Product Manual Set Multiple Mode - C6H Bit -> 7 6 5 4 3 1 0 C6H Command (7) X C/D/H (6) Drive X Cyl High (5) X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) Sector Count Feature (1) X loaded for all subsequent Read Multiple and Write Multiple commands and execution of those commands is enabled. If a block count is not supported, an Aborted Command error is posted, and Read Multiple and Write Multiple commands are disabled.
CompactFlash Memory Card Product Manual 6.1.20 Standby - 96H, E2H Bit -> 7 6 5 4 3 X C/D/H (6) Drive X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) X Feature (1) X 0 Recovery from sleep mode is accomplished by simply issuing another command (a reset is not required). This command causes the CompactFlash Memory Card to set BSY, enter the Sleep mode (which corresponds to the ATA “Standby” Mode), clear BSY and return the interrupt immediately. 6.1.
Preliminary 6.1.22 CompactFlash Memory Card Product Manual Translate Sector - 87H Bit -> 7 6 5 4 3 1 0 87H Command (7) C/D/H (6) 2 1 LBA 1 Drive Head (LBA 27-24) Cyl High (5) Cylinder High (LBA 23-16) Cyl Low (4) Cylinder Low (LBA 15-8) Sec Num (3) Sector Number (LBA 7-0) Sec Cnt (2) X Feature (1) X When this command is issued, the controller responds with a 512 byte buffer of information on the desired cylinder, head and sector with the actual Logical Address.
CompactFlash Memory Card Product Manual 6.1.23 Wear Level - F5H Bit -> 7 6 5 4 3 C/D/H (6) X X X Drive X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) Completion Status Feature (1) X This command is effectively a NOP command and only implemented for backward compatability with earlier SanDisk SDP series products. The 6.1.24 Write Buffer - E8H 0 7 6 5 Sector Count Register will always be returned with an 00H indicating Wear Level is not needed.
Preliminary 6.1.25 CompactFlash Memory Card Product Manual Write Long Sector - 32H, 33H Bit -> 7 6 5 4 1 LBA 1 Drive Cylinder High (LBA 23-16) Cyl Low (4) Cylinder Low (LBA 15-8) Sec Num (3) Sector Number (LBA 7-0) Sec Cnt (2) X Feature (1) X 0 mode. Because of the unique nature of the solidstate CompactFlash Memory Card, the four bytes of ECC transferred by the host cannot be used by the CompactFlash Card.
CompactFlash Memory Card Product Manual of the block or partial block transferred. The Write command ends with the sector in error, even if it is in the middle of a block. Subsequent blocks are not transferred in the event of an error. Interrupts are generated when DRQ is set at the beginning of each block or partial block. sectors (not the number of blocks or the block count) requested.
Preliminary 6.1.28 CompactFlash Memory Card Product Manual Write Sector(s) - 30H, 31H Bit -> 7 6 5 4 1 LBA 1 Drive 1 0 Head (LBA 27-24) Cyl High (5) Cylinder High (LBA 23-16) Cyl Low (4) Cylinder Low (LBA 15-8) Sec Num (3) Sector Number (LBA 7-0) Sec Cnt (2) Sector Count Feature (1) X BSY is cleared, DRQ is set and an interrupt is generated. When the final sector of data is transferred, BSY is set and DRQ is cleared.
CompactFlash Memory Card Product Manual 6.1.30 Write Verify Sector(s) - 3CH Bit -> 7 6 5 4 3 C/D/H (6) 2 1 0 3CH Command (7) 1 LBA 1 Drive Head (LBA 27-24) Cyl High (5) Cylinder High (LBA 23-16) Cyl Low (4) Cylinder Low (LBA 15-8) Sec Num (3) Sector Number (LBA 7-0) Sec Cnt (2) Sector Count Feature (1) X This command writes from 1 to 256 sectors as specified in the Sector Count Register. A sector count of zero requests 256 sectors.
Preliminary 6.2 CompactFlash Memory Card Product Manual Error Posting The following table summarizes the valid status and error value for all the ATA Command set.
CompactFlash Memory Card Product Manual Preliminary 7.0 CIS Description This section describes the Card Information Structure (CIS) for the CompactFlash Memory Card. 80 SanDisk CompactFlash Memory Card Product Manual Rev.
Preliminary CompactFlash Memory Card Product Manual Attribute Offset Data 7 6 5 000h 01h 002h 04h 004h DFh 006h 72h 008h 01h 1x 00Ah FFh 00Ch 1Ch 00Eh 04h 010h 03h 4 3 2 1 0 Description of Contents CIS Function Device Info Tuple Tuple Code Link is 4 bytes Link to next tuple I/O Device, No WPS, ext speed Device ID, WPS, Speed 700 nsec if no wait Extended Speed 2 Kilobytes of Address Space Device Size List End Marker End of Devices End Marker CISTPL_DEVICE_OC Oth
CompactFlash Memory Card Product Manual 82 Attribute Offset Data 02Ch 15h 02Eh 17h 030h 04h 032h 7 6 5 4 3 2 1 Description of Contents CIS Function Level 1 version / product info Tuple Code Link to next tuple is 23 bytes Link Length TPPLV1_MAJOR PCMCIA 2.0 /JEIDA 4.1 Major Version 01h TPPLV1_MINOR PCMCIA 2.0 /JEIDA 4.
Preliminary Attribute Offset Data 05Eh 80h 060h 03h 062h 14h 064h 08h 066h 00h 068h 21h 06Ah 02h 06Ch 04h 06Eh 01h 070h 22h 072h 02h 074h 01h 076h 01h CompactFlash Memory Card Product Manual 7 6 5 4 Description of Contents CIS Function CISTPL_VEND_SPECIF_80 SanDisk Parameters Tuple Tuple Code (Field Bytes 3-4 taken as 0) Link length is 3 byte Link to next tuple and length of info in this tuple No Wear Level & NO Vpp W:No Wear Level 12:Vpp Not used on Write NI:-INPAC
CompactFlash Memory Card Product Manual Attribute Offset Data 078h 22h 07Ah 03h 07Ch 02h 07Eh 0Ch 080h 84 0Fh 082h 1Ah 084h 05h 086h 01h 7 6 5 4 3 2 1 0 CISTPL_FUNCE Disk Function Extension Tuple Type R R R R U S V 0 0 0 0 1 1 0 R I E N P3 P2 P1 P0 0 0 0 0 1 1 1 1 CISTPL_CONF RFS RMS RAS 00 00 01 Preliminary Description of Contents CIS Function Function Extension tuple Tuple Code This tuple has 3 info bytes Link Length Basic PCMCIA-ATA Ex
Preliminary Attribute Offset Data 090h 1Bh 092h 0Bh 094h C0h 096h 098h 09Ah C0h A1h 27h CompactFlash Memory Card Product Manual 7 6 5 4 3 2 1 0 CISTPL_CE Description of Contents CIS Function Configuration Entry Tuple Tuple Code Link to next tuple is 11 bytes. Also limits size of this tuple to 13 bytes.
CompactFlash Memory Card Product Manual Attribute Offset Data 7 0A2h 75h X 0 0A4h 08h Length in 256 bytes pages (lsb) 0A6h 00h Length in 256 bytes pages (msb) 0A8h 21h 0AAh 1Bh 0ACh 06h 0AEh 00h 0B0h 0B2h 86 01h 21h 6 5 4 3 2 Mantissa Eh = 8.
Preliminary Attribute Offset Data 0BAh 1Bh 0BCh 0Dh 0BEh C1h 0C0h 0C2h 0C4h 41h 99h 27h CompactFlash Memory Card Product Manual 7 6 5 4 3 2 1 0 CISTPL_CE I D Configuration Index 1 1 1 W R P B Interface Type 0 1 0 0 1 M MS 1 0 IR IO T P 1 0 1 1 R DI PI AI SI HV LV NV 0 0 1 0 0 1 1 1 Description of Contents CIS Function Configuration Entry Tuple Tuple Code Link to next tuple is 13 bytes. Also limits size of this tuple to 15 bytes.
CompactFlash Memory Card Product Manual Attribute Offset Data 7 0CCh 75h X 0 0CEh 64h R S E IO AddeLines 0 1 1 4 S P L M V B I N 1 1 1 1 0 0 0 0 7 6 5 4 3 2 1 0 1 1 1 1 1 1 1 1 F E D C B A 9 8 1 1 1 1 1 1 1 1 X R P RO A T 0 0 1 0 1 0D0h 0D2h 0D4h 0D6h 88 F0h FFh FFh 21h 6 5 4 3 Mantissa Eh = 8.
Preliminary Attribute Offset Data 0D8h 1Bh 0DAh 06h 0DCh 01h 0DEh 0E0h 01h 21h CompactFlash Memory Card Product Manual 7 4 3 2 1 0 I D Configuration Index 0 0 1 M MS 0 0 IR IO T P 0 0 1 0 R DI PI AI SI HV LV NV 0 0 B5h X 1 0E4h 1Eh X 0 0E6h 4Dh X 0 0E8h 1Bh 0EAh 12h 0ECh C2h 41h 5 CISTPL_CE 0E2h 0EEh 6 1 0 0 0 Mantissa 6h = 3.0 0 CIS Function Configuration Entry Tuple Tuple Code Link to next tuple is 6 bytes.
CompactFlash Memory Card Product Manual Attribute Offset Data 7 0F0h 99h M MS 1 0 0F2h 90 27h 6 5 4 3 2 IR IO T P 1 0 1 1 1 0 R DI PI AI SI HV LV NV 0 0 1 0 0 1 1 1 Preliminary Description of Contents CIS Function Vcc Only Power Description; No Timing; I/O and IRQ present; No Mem Space; Misc Entry present P:Power info type T:Timing info present IO:I/O port info present IR:Interrupt info present MS:Mem space info type M:Misc info byte(s) present TPCE_FS Nominal Volta
Preliminary Attribute Offset Data 0FEh 61h CompactFlash Memory Card Product Manual 7 6 5 4 3 2 1 0 LS AS N Ranges - 1 1 2 1 Description of Contents CIS Function Number of Ranges is 2; Size of each address is 2 bytes; Size of each length is 1 byte.
CompactFlash Memory Card Product Manual Attribute Offset Data 110h 1Bh 112h 06h 114h 02h 116h 118h 92 01h 21h 7 6 5 4 3 2 1 0 CISTPL_CE I D Configuration Index 0 0 2 M MS 0 0 IR IO T P 0 0 1 0 R DI PI AI SI HV LV NV 0 0 11Ah B5h X 1 11Ch 1Eh X 0 11Eh 4Dh X 0 1 0 0 Mantissa 6h = 3.0 0 0 Description of Contents CIS Function Configuration Entry Tuple Tuple Code Link to next tuple is 6 bytes. Also limits size of this tuple to 8 bytes.
Preliminary Attribute Offset Data 120h 1Bh 122h 12h 124h C3h 126h 128h 12Ah 41h 99h 27h CompactFlash Memory Card Product Manual 7 6 5 4 3 2 1 0 CISTPL_CE I D Configuration Index 1 1 3 W R P B Interface Type 0 1 0 0 1 M MS 1 0 IR IO T P 1 0 1 1 R DI PI AI SI HV LV NV 0 0 1 0 0 1 1 1 Description of Contents CIS Function Configuration Entry Tuple Tuple Code Link to next tuple is 18 bytes. Also limits size of this tuple to 20 bytes.
CompactFlash Memory Card Product Manual Attribute Offset Data 7 6 5 134h EAh R S E IO AddeLines 1 1 1 Ah = 10 136h 94 61h 4 3 2 1 0 LS AS N Ranges - 1 1 2 1 Preliminary Description of Contents CIS Function Supports both 8 and 16 bit I/O hosts. 10 Address lines with range so card will respond only to indicated (170-177, 376-377) on A9 through A0 for I/O cycles.
Preliminary CompactFlash Memory Card Product Manual Attribute Offset Data 7 6 5 146h 21h X R P RO A T 0 0 1 0 1 148h 1Bh 14Ah 06h 14Ch 03h 14Eh 150h 01h 21h 4 3 0 2 1 0 CISTPL_CE Description of Contents CIS Function Power-Down, and Twin Card. T:Twin Cards Allowed A:Audio Supported RO:Read Only Mode P:Power Down Supported R:Reserved X:More Misc Fields Bytes TPCE_MI Configuration Entry Tuple Tuple Code Link to next tuple is 6 bytes.
This page intentionally left blank 96 SanDisk CompactFlash Memory Card Product Manual Rev.
Ordering Information and Technical Support SanDisk CompactFlash Memory Card Product Manual Rev.
This page intentionally left blank 98 SanDisk CompactFlash Memory Card Product Manual Rev.
Ordering Information and Technical Support Ordering Information To order SanDisk products directly from SanDisk, call 408-542-0595. CompactFlash Memory Card CompactFlash Memory Card Evaluation Kit Model SDCFBX-YY-101 Where: X: I Industrial temperature grade (blank) Standard temperature grade YY: 8 8.02 MB 16 16.05 MB 32 32.11 MB 64 64.22 MB 128 128.45 MB 192 192.41 MB 256 256.90 MB 384 384.49 MB 512 512.
Ordering Information and Technical Support System Software, Card Reader/Writers and Connectors Compatible with SanDisk CompactFlash Memory Cards Table 1 System Software with SanDisk CompactFlash Memory Card Support Vendor Product Name Telephone Number AMI AMICARDZ 770-263-8181 Award/VMI Cardware 415-968-4433 Databook Card Talk for Databook Chip 508-762-9779 Phoenix Phoenix Card Manager Plus 714-440-8000 SystemSoft Card Soft 508-651-0088 Vadem Socket Services for VG365, VG465, VG468 408-4
Ordering Information and Technical Support Table 2 Card Readers/Writers Compatible with SanDisk CompactFlash Memory Cards (continued) Vendor Country CardWize United Data Solutions Kingdom Telephone/FAX Number Country Code 44 118-947-9475 FAX 118-947-4676 Email pcmcia@cardwize.co.uk Product Model Product Type MiniWizard 1R WIZ/001 ISA adapter with one rear access slot. MiniWizard 2R WIZ/006 ISA adapter with two rear mounted slots.
Ordering Information and Technical Support Table 2 Card Readers/Writers Compatible with SanDisk CompactFlash Memory Cards (continued) Vendor Country Chase/CNF United States 408-778-1160 FAX 408-779-6558 United Kingdom Country Code 44 (0) 1274 841358 FAX (0) 1274 841316 Germany Country Code 49 (0) 711 7796420 FAX (0) 711 7796440 CSM Telephone/FAX Number Product Model Product Type CARDport isa ISA adapter with one slot on card and cable to single slot drive bay mounted unit.
Ordering Information and Technical Support Table 3 CompactFlash Connector Vendors The table below lists vendors that can supply CompactFlash connectors. Vendor Name Telephone Number 3M Company 800-225-5373 Amp Incorporated 800-522-6752 (USA only) 717-986-7777 (outside USA) Hirose Electric Incorporated 805-522-7958 Molex Incorporated 630-969-4550 SanDisk CompactFlash Memory Card Product Manual Rev.
Ordering Information and Technical Support Technical Support Services Direct SanDisk Technical Support Call SanDisk Applications Engineering at 408-542-0405 for technical support. SanDisk Worldwide Web Site Internet users can obtain technical support and product information along with SanDisk news and much more from the SanDisk Worldwide Web Site, 24 hours a day, seven days a week. The SanDisk Worldwide Web Site is frequently updated.
SanDisk Sales Offices SanDisk CompactFlash Memory Card Product Manual Rev.
This page intentionally left blank 106 SanDisk CompactFlash Memory Card Product Manual Rev.
SanDisk Worldwide Sales Offices SanDisk Worldwide Sales Offices Americas Europe SanDisk Corporate Headquarters 140 Caspian Court Sunnyvale, CA 94089-9820 408-542-0500 FAX 408-542-0503 http://www.sandisk.com Sales Offices Western Region USA 408-542-0730 FAX 408-542-0403 SanDisk GmbH Karlsruher Str.
This page has been left blank intentionally. 108 SanDisk CompactFlash Memory Card Product Manual Rev.
Appendix CompactFlash Connector Specifications Appendix CompactFlash Connector Specifications This appendix includes specifications for CompactFlash connectors as defined by the CompactFlash Association. See the Ordering Information section of this manual for a list of CompactFlash connector vendors.
Appendix CompactFlash Connector Specifications Pin Insertion 0.94mm (.037 in.) Min. Figure 2 Socket Connector Entry 110 SanDisk CompactFlash Memory Card Product Manual Rev.
Appendix CompactFlash Connector Specifications Description Pin Number L ± 0.10 L1 Max L2 Ref L3 ± 0.10 L4 Power 1, 13, 38 & 50 5.00 [.197] 0.50 [.020] 4.50 [.177] 0.50 [.020] 0.50 - 2.50 [.020 - .098] General All other pins 4.25 [.167] 0.50 [.020] 3.75 [.148] 0.50 [.020] 0.50 - 2.50 [.020 - .098] Detect 25, 26 3.50 [.138] 0.50 [.020] 3.00 [.118] 0.50 [.020] 0.50 - 2.50 [.020 - .098] L 1 L3 2 L4 L1 L2 Pin Socket Notes: 1 Pin/Socket contact area.
Appendix CompactFlash Connector Specifications 43.03mm ± 0.08 (1.694 in.) 3.5mm ± 0.08 (.138 in.) 1.4mm ± 0.05 (.055 in.) 0.79mm ± 0.05 (.031 in.) Pin 1 Pin 25 Pin 26 Pin 50 2X 0.89mm ± 0.05 (.035 in.) Figure 4 Pin Connector Opening 110° Min Contact Area 0.50mm ± 0.10 (.020 in.) 10° - 15° CL Row 0.46mm Max. (.018 in.) Ø 0.44mm ± 0.02 (.017 in.) Cross Section Tip Detail Figure 5 Header Pin Detail 112 SanDisk CompactFlash Memory Card Product Manual Rev.
Appendix CompactFlash Connector Specifications 47.96mm (1.888 in.) 1.27mm Typ (.050 in.) 2x 1.35mm ± 0.05 (.053 in.) 45.06mm (1.774 in.) 2x 1.42mm ± 0.05 (.056 in.) 0.79mm ± .002 (.031 in.) 1.40mm ± 0.05 (.055 in.) Pin 1 Pin 13 Pin 26 Pin 38 Pin 25 Pin 50 1.27mm Typ (.050 in.) Pin No. Pin Type Interface Dim A detect 3.50mm (.138 in.) 25, 26 general 4.25mm (.167 in.) all other pins power 5.00mm (.197 in.) 1, 13, 38, 50 43.03mm ± 0.08 (1.694 in.) 2X 0.89mm ± 0.05 (.035 in.) 2X 6.
Appendix 2X ø 2.20mm (.087 in.) CompactFlash Connector Specifications 40.16mm (1.581 in.) 0.635mm Typ (.0250 in.) Pin Type Interface Dim A detect 3.50mm (.138 in.) Pin No. 25, 26 general 4.25mm (.167 in.) all other pins power 5.00mm (.197 in.) 1, 13, 38, 50 4.50mm (.177 in.) A 2X 4.00mm (.157 in.) (Optional) 1.00mm (.039 in.) —A— ø1.50mm (.059 in.) 1.00mm (.039 in.) (Optional) A —A— 2X 2.00mm (.079 in.) (Optional) 1.50mm (.059 in.) 50.6mm (1.99 in.) (Optional) 43.03mm ± 0.06 (1.
Appendix CompactFlash Connector Specifications 1 25 26 50 0.635mm Typ (.0250 in.) 1.27mm Typ (0.050 in.) Insert Card 30.48mm (1.200 in.) Figure 8 Two Row SMT Host PCB Pattern 31.11mm (1.225 in.) 0.40mm Typ (.016 in.) 0.635mm Typ (.0250 in.) 3.50mm (.138 in.) 26 1 Insert Card 25 50 Figure 9 Single Row SMT Host PCB Pattern 24 25 1 2 50 26 5.72mm Ref (.225 in.) 3X 1.91mm (.075 in.) Insert Card 27 30.48mm (1.200 in.
Appendix CompactFlash Connector Specifications 24 25 1 2 50 26 5.72mm Ref (.225 in.) 3X 1.91mm (.075 in.) 30.48mm (1.200 in.) 27 49 Figure 11 Vertical Through Hole Host PCB Pattern 1.27mm (.050 in.) 1 25 26 50 1.27mm (.050 in.) Insert Card 30.48mm (1.200 in.) Figure 12 Alternate Right Angle Through Hole Host PCB Pattern 116 SanDisk CompactFlash Memory Card Product Manual Rev.
Limited Warranty Limited Warranty I. WARRANTY STATEMENT SanDisk warrants its products to be free of any defects in materials or workmanship that would prevent them from functioning properly for one year from the date of purchase. This express warranty is extended by SanDisk Corporation. II. GENERAL PROVISIONS This warranty sets forth the full extent of SanDisk’s responsibilities regarding the SanDisk CompactFlash Memory Card.
Limited Warranty reserves the right to market any products, whether new, repaired, or rebuilt, under different specifications and product designations if such products do not meet the original product’s specifications. IV. RECEIVING WARRANTY SERVICE According to SanDisk’s warranty procedure, defective product should be returned only with prior authorization from SanDisk Corporation.
