NETWORK CAMERA User Manual XND-6010/6020R/8020R/8030R/8040R XNV-6010/6020R/8020R/8030R/8040R
Network Camera User Manual Copyright ©2017 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) 7.
overview Class construction An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. Battery Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S.
CONTENTS web viewer overview 6 7 8 10 installation & connection 12 12 13 16 16 17 network connection and setup 20 20 20 21 21 22 22 24 24 25 25 Important Safety Instructions Product Features Recommended PC Specifications Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs What’s Included At a Glance (XND-6010/6020R/8020R/ 8030R/8040R) At a Glance (XNV-6010/6020R/8020R/ 8030R/8040R) Installation (XND-6010/6020R/8020R/ 8030R/8040R) Installation (XNV-6010/6020R/8020R/ 8030R
overview Product Features •• Dustproof/Waterproof (IP67, IP66) (XNV-6010/6020R/8020R/8030R/8040R) The dustproof and waterproof design makes you feel at ease when installing the product outdoors or exposing it to rain. •• IR mode (XND/V-6020R/8020R/8030R/8040R) If the IR indicator turns on, the product switches to the IR mode for preventing an object from being too bright, which helps you identify the object in near distance.
What’s Included Appearance Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.
overview At a Glance (XND-6010/6020R/8020R/8030R/8040R) Components b Appearance b c b 7 e f g V 456 12 123 T i h VIDEO T RESE 123 456 e f g 7 i h Item US B T RESE d FRON DC V 12 VIDEO DC US B T 1 2 d FRON c 1 2 a Description a Dome cover Case cover used to protect the lens and the main unit. b Microphone hole Microphone is embedded. c Camera Case Housing part that covers the camera body.
Item Description Illumination Sensor Detects incoming light to control the IR LED. b Lens Lens for the camera. c IR LED These infrared LED’s are controlled by the illumination sensor. ●● overview a Port to connect audio and alarm cables. d Audio and alarm cable port ARM-IN Used to connect the alarm input sensor or external day/night sensor. GND These are common ports to connect alarm input/output signals.
overview At a Glance (XNV-6010/6020R/8020R/8030R/8040R) Components b Appearance a b a T 1 2 1 d FRON 1 2 2 c d FRON T FRON T RESE 4 123 123 7 V 456 12 T RESE T RESE 123 456 7 N W T AF RESE VID EO Description a Dome cover Case cover used to protect the lens and the main unit. b Camera Case Housing part that covers the camera body.
Item Description Illumination Sensor Detects incoming light to control the IR LED. b Lens Lens for the camera. c IR LED These infrared LED’s are controlled by the illumination sensor. ●● overview a Port to connect audio and alarm cables. d Audio and alarm cable port ARM-IN Used to connect the alarm input sensor or external day/night sensor. GND These are common ports to connect alarm input/output signals.
installation & connection 123 RESE T B V 456 7 NT FRO 4. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. (page 15) recommend you not to touch the lens as the camera lens has been JJ `` We properly focused in the final process of manufacturing. If so, the lens may be out of focus or stained by alien substances. 5. Please connect the inner cover to the main body.
Installation (XNV-6010/6020R/8020R/8030R/8040R) 123 RESET 456 W T VIDEO 7 AF VIDEO N ●● installation & connection RESE B AC V/ 24 DC F V + T 12 - 1. Using the L wrench provided, turn the 2 fastening bolts on the dome cover counter clockwise to remove the cover. 12 V Disassembling US •• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.
installation & connection Attaching to the unbundled adapter 5. Insert the LAN cable into the large hole made by removing the projected part of the rubber plug in step 2 above. Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience. 6. Remove the sheath with a cable cutter, and align the cables. 7. Connect the LAN cable with a LAN connector, and insert it into the LAN tool. 2.
Adjusting the monitoring direction for the camera Pan 12 B V T US 123 456 7 NT FRO 1 2 Tilt 2. CEILING MOUNT ADAPTOR(SBP-300CM)/HANGING MOUNT(XND6010/6020R/8020R/8030R/8040R : SBP-300HM7, XNV-6010/6020R/ 8020R/8030R/8040R : SBP-122HM) This adaptor is used when installing the dome camera on a concrete ceiling. Lens rotation `` Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling.
installation & connection Inserting/Removing a Micro SD Memory Card JJ JJ `` Pressing too hard on the Micro SD memory card can cause the card to shoot out uncontrollably from the slot when released. `` Before removing the Micro SD memory card, in , set the device to and press the [Apply] button and turn the camera off. (Page 47) `` Disconnect the power cable from the camera before inserting the Micro SD memory card.
Connecting with other Device Ethernet Connection Connect the Ethernet cable to the local network or to the Internet. Wi-Fi dongle SOFT AP ●● installation & connection Connecting Wi-Fi Camera Setup 1. Connect OTG gender (5-pin) and WiFi dongle to the micro USB terminal. Monitor to install A T C K LIN NETW ORK Smartphone Setup 2. Select the camera SSID after turning on the WiFi. 1 2 1. Install the Wisenet Installation application. 3. Run the Wisenet Installation application.
installation & connection Power Cable Specification for Each Model In case of DC 12V Input: Model XND/V-6010 XND/V-6020R/8020R/8030R/8040R Network Cable Specification Item Connector Ethernet Cable Max Distance PoE Support 2. Connect the AUDIO OUT port of the camera with the speaker or LINE IN port of the amplifier that the speaker is connected to. Wire Type (AWG) #22 #20 #20 #18 Cable Length (Max.) 15m 24m 17m 27m Contents RJ45 10/100Base-T UTP Category 5e 100M IEEE 802.3af Remark 10/100 Mbps 3.
To connect the external sensor Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port, and connect the other strand to the [GND] port. External connection Inside of the camera VCC_3.3V RESISTOR Sensor ALARM IN (5mA SINK) ●● installation & connection Alarm In Wiring Diagram RESISTOR RESISTOR MLCC GND DIODE TRANSISTOR GND To connect the alarm out If devices (e.g.
network connection and setup You can set up the network settings according to your network configurations. Connecting the Camera Directly to Local Area Networking Connecting the Camera Directly to a DHCP Based DSL/Cable Modem Connecting to the camera from a local PC in the LAN INTERNET DSL/Cable Modem 1. Launch an Internet browser on the local PC. External Remote PC Camera 2. Enter the IP address of the camera in the address bar of the browser. DDNS Server (Data Center, KOREA) Camera 1.
Connecting the Camera Directly to a PPPoE Modem Connecting the Camera to a Broadband Router with the PPPoE/Cable Modem This is for a small network environment such as homes, SOHO and ordinary shops. INTERNET PPPoE Modem Camera Camera DDNS Server (Data Center, KOREA) Camera 1. Connect the user PC directly with the network camera. 2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on your desktop to connect to the Internet. 3.
network connection and setup Buttons used in IP Installer a b c d Item e f g Description Scans for cameras with the IPv6 setting. Activated in an IPv6 compliant environment only. i IPv6 j Search Scans for cameras that are currently connected to the network. However, this button will be grayed out if neither IPv4 nor IPv6 is checked. k l m Auto Set The IP Installer automatically configures the network settings. Manual Set You should configure the network settings manually.
If not using a Broadband Router If the Broadband Router has more than one camera connected 4. In the pane, provide necessary information. •• HTTP Port : Used to access the camera using the Internet browser, defaulted to 80. •• VNP Port : Used to control the video signal transfer, defaulted to 4520. ex) For setting , , and , contact your network administrator.
network connection and setup Dynamic IP Setup Dynamic IP Environment Setup •• Example of the Dynamic IP environment -- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server 3. When done, click [Save Settings]. Your settings will be saved. MM `` Above sample instructions are based on the CISCO’s Broadband Router. `` The settings may differ depending on the connected Broadband Router model. For more information, refer to the user manual of the applicable router.
Connecting to the Camera from a Shared Local PC 1. Run the IP Installer. It will scan for connected cameras and display them as a list. ●● network connection and setup 2. Double-click a camera to access. The Internet browser starts and connects to the camera. to the camera can also be gained by typing the camera’s IP MM `` Access address in the address bar of the Internet browser.
web viewer Connecting to the Camera Normally, you would 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2.
Password setting a new password with 8 to 9 digits, you must use at least 3 of JJ `` For the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. -- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].
web viewer Installing WebViewer Plugin To access to the plug-in webviewer and play a live video (H.264/H.265) or a recorded video, an installation message will be prompted. At this time you need to install the webviewer plug-in to use the function properly. Using the Live Screen a b c d e f 1. When the monitoring page is accessed for the very first time, the installation page is displayed. Click [Plugin] to begin installation.
Item Description You can select a profile type in
web viewer To Use Microphone Click [Mic ( )] icon to activate the microphone. To check the profile status You can check the profile information. MM `` If you are using IE or the Safari browser, you will need to install plug-in. To count the number of pixels 1. Click the [Pixel count ( )] icon to activate it. 2. Drag the mouse on the video to select an area. 3. The number of pixels in the selected area is displayed on the screen. To control PTZ 1. Click the [PTZ ( 1. Click the [Status ( )] icon.
Playing the recorded video Item MM `` Before you can play the video, you must configure the record settings. For details on record settings, refer to “Storage”. (page 47) e Search range setting Set the search date and time range for data saved in your Micro SD memory card or NAS. f Capture Saves the current video screen in an image file format (format may vary depending on the browser). g Backup Set the desired date to make a backup copy of video data saved in your Micro SD memory card or NAS.
web viewer To play after searching by time To Play an AVI File 2. On the calendar, set the search date, start time and end time. The event searched is displayed on the time bar. 1. Separate the Micro SD memory card from the camera. 1. Click the [ ] icon. 3. Click the [Play ( )] button. The video at the selected time will be played. 4. When a video is played, the recording time of the video currently being played is displayed. 5. Search the video forward and backward and adjust the playback speed.
setup screen Setup You can configure the basic information of the camera, PTZ, video & audio, network, event, analysis, and system settings of the camera over the network. 2. The Setup screen appears. )] button. -- Control compression : Control the compression rate if the network bandwidth drops down. Compression adjustment can cause deterioration of the image quality. Basic Setup Video profile 1. From the Setup menu, select the .
setup screen To Add/Change the Video Profile The profile setup can be added or modified to accommodate various profiles depending on the recording conditions. 1. In
To Use Crop Encoding User 2. Click . The Crop Encoding Area Setup window will pop up. •• 16:9 : The aspect ratio shall be set to 16:9 as close as to the user specified area. The supporting size ranges from 640X360 to 1280X720 and supporting output resolutions are 640X360, 800X448, 1280X720. •• 4:3 : The aspect ratio shall be set to 4:3 as close as to the user specified area.
setup screen •• Current users : If you select
6. Click . 7. Type in each item in the Port menu as necessary. `` Neither the port range between 0 and 1023 nor port 3702 is available. •• HTTPS : In this version, the security of the web communication protocol HTTP is strengthened. It can be used when you set HTTPS mode in SSL. The initial value is set to 443(TCP). `` The available setting range is 1024~65535. (For security reasons, in your Safari or Google Chrome browser, you may not use 65535 as your HTTPS port.
setup screen Video & Audio setup Video setup 1. From the Setup menu, select the
Camera setup You can change the camera settings according to the environment where the camera is located. 1. From the Setup menu, select the
setup screen To Set the Sensor To Set BLC 1. Select . 1. Select . It specifies how many frames the camera CMOS sensor will capture per second. 2. Select . MM `` Refer to “Video profile” for the framerate setup range of the
To Set WDR It displays a sharp image of the objects in a scene where both bright and dark areas exist. 1. Select . 3. Select each item and set it properly. •• WDR level : Adjusts the intensity of backlight compensation. •• Auto : Detects the surrounding environment and automatically uses backlight compensation. •• Turn off in low light : Does not use automatic backlight compensation when detecting a dark environment.
setup screen •• Dwell Time : It specifies the period for which the selected brightness condition must be maintained to switch the lighting mode from Day to Night or vice versa. •• Duration : It specifies the interval of lighting mode conversion. •• Alarm in : The video is set to Color or B/W as the alarm sensor is open or closed. `` If the Day/Night mode is set to External Input, the alarm input function of the Event-Alarm Input page is disabled.
Smart codec Set a desired area of the video incoming from the camera as ROI area and specify the detection sensitivity for the area. )> DDNS DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of a camera into a general Host Name so that the user can easily remember it. 2. Click . JJ `` You can use the DDNS service only if the internet is connected. 4. Specify an area of interest to monitor manually. 2. Click . 6.
setup screen Registering with DDNS To connect to the Wisenet DDNS in camera setup 1. Visit the Wisenet DDNS web site (http://ddns.hanwhasecurity.com) and sign in with a registered account. 2. Provide the that you registered product ID with the DDNS site. To register your product with the Wisenet DDNS 2. From the top menu bar, select . 3. Click the [Register Product] tab. 4. Enter the product ID. 1. From the DDNS setup page, set to . 3. Click [Apply].
selected for IP Filtering and of is set to
setup screen QoS You can specify the priority to secure a stable transfer rate for a specific IP. 1. From the Setup menu, select the . )> tab. 3. Click the [Add] button. The IP list will be created. -- IP address : Enter the IP address to which messages will be sent. -- Authentication failure notification : It specifies whether an event shall be generated when the community information is invalid.
Event Setup •• E-mail configuration -- Server address : Enter the SMTP address of the email server that you transfer the alarm or event images to. Event setup -- Authentication : Select whether to use authorization. 2. Click . -- ID : Enter the user ID for logging into the email server. 1. From the Setup menu, select the tab. 3. Activate desired items on the Event list. -- Password : Enter the user account password for logging into the email server. 4.
setup screen To make recording on the Micro SD memory If you want to record in your NAS 2. Click the [Apply] button. deletion is supported only if your NAS meets the recommended JJ `` Auto specifications. 1. Set the SD card unit to . 3. Check the memory card’s and . You can format the Micro SD card by clicking the button. `` Some frames may be skipped if the Micro SD memory card operates at the lower speed than recommended.
NAS (Network Attached Storage) guide JJ `` Since data may not be saved after a temporary network interruption when using NAS, it is recommended that you use SD at the same time to prevent loss of recorded images. 4. Click the [Create] button. 5. After entering the shared folder name(ID), click the [OK] button to create a shared folder. In this example, the shared folder name is [testDirectory].
setup screen 10. Basic setting in the NAS is completed. Connect your camera to the actual NAS. As shown below, enter the NAS connection setting items. 1. From the Setup menu, select the tab. 3. Configure the camera alarm output settings. `` If you change the alarm output type, the alarm out button on the monitoring page and alarm output type displayed on Event Setup page will be changed accordingly. •• Type -- N.O.
Time schedule You can configure settings to transmit images at regular intervals at a scheduled operation time regardless of the occurrence of an event. 2. Click
setup screen Configure analysis settings Motion detection You can configure settings to generate an event signal when a motion is detected. 1. From the Setup menu, select the . )> tab. 3. Set whether or not to . 4. Set an and . You can set up to 8 areas. You can configure level, sensitivity, and handover settings for each area of interest. A single area supports a shape with up to 8 vertexes.
Defocus detection You can configure settings to generate an alarm signal when a defocus of the camera lens is detected. 1. From the Setup menu, select the . 4. Configure settings for each item. •• Level of detection : An alarm is generated if the current level is higher than the detection level configured. •• Sensitivity : The higher the intensity is, the higher the level of the chart that is output for the same video.
setup screen Face detection You can configure the settings to generate an event signal in response to the detection of a face in the specified area. 1. From the Setup menu, select the . )> tab. 4. Set an and . `` You can set an area of interest only in a rectangular shape. `` A face that is smaller than the circle marked in the center of the area of interest is not detected. 5. Set the sensitivity level.
Sound classification •• Size 1. Select the tab. 3. When done, click [Apply]. Audio detection You can set to detect sound over the specified level and trigger an event accordingly. 1. From the Setup menu, select the . )> tab. 3. Set whether or not to . 4. Set the audio detection’s sound level. The lower the level, the smaller the sound change is detected.
setup screen Statistics setup 8. When done, click [Apply]. 9. To delete all data from the people counting statistics, click the button. People Counting The people counting function lets you check the number of people entering a designated area through video analysis. 1. From the Setup menu, select the . )> tab.
To set heat map You can configure settings related to heat map. Figure 1) 1. Click . 2. Select the tab. ●● setup screen 3. Enable or disable the Heat Map option. 4. Select a background color. 5. Enable or disable the Report option. If you select , you can receive heat map data at regular intervals. - , you should configure the FTP settings MM `` Into receive data. 6. When done, click [Apply]. 7.
setup screen Figure 4) Figure 5) Live 08:22:23 Live 08:22:23 Hanwha Techwin 58_ setup screen Hanwha Techwin
System Setup Product information 1. Click [Browse ( )> tab. 3. Check the camera information, or provide details according to your network environment. •• Model : Model name of the product. •• Serial number : Product serial number. •• Device name : Provide a device name that will be displayed on the Live screen. •• Location : Specify the location where the camera is installed. •• Description : Provide detailed information about the camera location.
setup screen Open Platform Setup Log You can check the system log or event log. 1. From the Setup menu, select the . )> tab. 3. Select a log type. •• Access Log : You can check the log information that contains the user’s access and the access time. •• System log : You can check the system logs where any system changes are recorded including the time information. •• Event log : You can check the event logs including the time information. 4.
appendix Specification Items 1945(H) x 1109(V) 2.16M Scanning System Progressive Scan Min. Illumination S / N Ratio Video Out Focal Length (Zoom Ratio) Lens 1945(H) x 1097(V) 2.13M Color : 0.055 lux(F2.0, 1/30sec), B/W : 0.0055 lux(F2.0, 1/30sec) 50dB 2.4mm Fixed 4mm Fixed F1.4 Angular Field of View H: 139˚, V: 73˚, D: 167˚ H: 88.6˚, V: 47.5˚, D: 104.8˚ Min. Object Distance 0.4m Lens Type Fixed 1/1.
appendix Items Video & Audio Analytics Alarm I/O Alarm Triggers Operational Alarm events XND/V-6010 Description XND/V-6020R Items XND-8020R/8030R/8040R XNV-8020R/8030R/8040R Tampering, Loitering, Directional Detection, Defocus Detection, Fog&Dust Detection, Virtual Line, Enter/Exit, Appear / Disappear, Audio Detection, Face Detection, Motion Detection, Digital Auto Tracking, Sound Classification, People counting, Heat map Video Quality Adjustment Bitrate Control Method Input 1ea / Output 1ea Alar
Items Webpage Language XND/V-6010 Description XND/V-6020R XND-8020R/8030R/8040R XNV-8020R/8030R/8040R XND-6010/6020R/8020R/8030R/8040R Unit : mm (inch) ●● appendix English, Korean, French, German, Spanish, Italian, Chinese, Russian, Japanese, Swedish, Portuguese, Czech, Polish, Turkish, Dutch, Hungarian, Greek Product Overview Supported OS : Windows 7 / 8.1 / 10, MAC OS X 10.10, 10.11, 10.
appendix XNV-6010/6020R/8020R/8030R/8040R Unit : mm (inch) Troubleshooting PROBLEM When an Windows 10 user accesses the web viewer through Chrome or Firefox, the sound volume of microphone changes periodically. No video is displayed when accessing the plug-in free webviewer on Safari via HTTPS. SOLUTION yy This is what happens when microphone driver has been set to Realtek driver. Install the High Definition Audio device (Windows Default Driver) or the third party driver as the microphone driver.
PROBLEM A. Check settings. B. The should be set to . C. Check if the option of menu is checked to use. ●● appendix of is set to , but no notification e-mail reaches me even when an analysis event had occurred. SOLUTION yy Verify the settings in the following sequence: No signal is found at the Alarm Output port even when an intelligent video yy Check alarm output port settings.
Open Source Announcement GPL/LGPL software license If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged. Component Name License Base Kernel Busybox iproute2-4.3.0 iptables-1.4.21 ethtool-4.2 mtd-1.5.2 mii-diag-2.11 rp-pppoe-3.11 wpa_supplicant-2.5 bash-4.3.30 zeroconf GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 3.0 GPL 2.
components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4.
2. Basic Permissions. All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither the name of Sparta, Inc nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
1.11. "Source Code" means the preferred form of the Covered Code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an Executable, or source code differential comparisons against either the Original Code or another well known, available Covered Code of the Contributor’s choice.
provides that the language of a contract shall be construed against the drafter shall not apply to this License. 12. RESPONSIBILITY FOR CLAIMS. As between Initial Developer and the Contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this License and You agree to work with Initial Developer and Contributors to distribute such responsibility on an equitable basis.
16. "Patch for Modification" means a difference, program, system, or the like in order to create the Modified Source Code from the Source Code or the Binary Code thereof. 17. "Vicarious Execution of Patch Processing" means vicarious execution service to create the Modified Source Code applying the Patch for Modification to the Source Code or the Binary Code thereof. 18. "Source Code User" means a person who uses the Source Code. 19.
"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.
PHP 3.01 License The PHP License, version 3.01 Copyright (c) 1999 - 2010 The PHP Group. All rights reserved. Component Name License URL php-5.2.17 PHP 3.01 http://www.php.net/distributions Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
Head Office 6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 Rep. of KOREA Tel : +82.70.7147.8753 Fax : +82.31.8018.3740 www.hanwha-security.com Hanwha Techwin America 500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666 Toll Free +1.877.213.1222 Direct +1.201.325.6920 Fax +1.201.373.0124 www.hanwha-security.com Hanwha Techwin Europe Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom Tel +44.1932.57.8100 Fax +44.1932.57.8101 www.hanwha-security.
