User Manual

ManualsBrandsSamsung ManualsWashing Machine: Twin Tub TypeWT10C1

1 2

BEFORE USING THE WASHER

CAUTIONS

PRECAUTIONS WHEN OPERATING

DESCRIPTION OF PARTS

● Remove the cap-hose from the drain

hose.

● In case of pump drained washer,

remove the cap-hose from

the drain hole.

● Be sure that the washer is grounded.

To avoid electrical shock,use

a metal pipe for the ground

connection. But, don't ground

the washer with gas pipes or

telephone lines to avoid to

dangers of explosion or lightning strike.

● Do not put your hands into the spin

dryer basket when it is spinning.

Your fingers can be caught

by spinning laundry and

damaged.

● Ventilation

opening must not be obstructed

by carpeting when the washing machine is

installed on a carpeted floor.

● If the supply

cord of this appliance is damaged,

it must only be replaced by a repair shop

appointed by the manufacturer,because

special purpose tools are required.

● To

avoid overfilling and damages this appliance

must be filled with the operator present using a

moderate water supply pressure only.

● This appliance is to be connected to the water

mains using new hose-sets and that

old hose-sets should not be reused.

● Never allow children to operate

or play with the washer.

Children playing with the washer

may accidentally fall into the

washing tub.

● Be sure to cover with the inner

cover on laundry before spinning.

This prevents laundry from

being tossed out and damaged.

● Before washing,check all pockets.

If nails or pins remain in pockets,they may

damage the washer or clothes.

● Close the water tap a little if the

water pressure is too high.

● To avoid water splashes,

close the wash tub lid.

● Never splash water on the control panel.

● Disconnect the power cord from the

power supply when not in use.

● Don't use excessively hot water.

(50˚C or more)

Plastic parts may be deformed or damaged.

Also, clothing may be deformed or decolored.

INNER LID

DRAIN HOSE

(with pump)

When you open this lid while

the spin basket is spinning,

the spinning will be stopped

by breake system.

POWER CORD

EARTH WIRE

(Option)

WATER DRAIN HOSE

(WITHOUT PUMP)

SPIN DRYER BASKET

SPIN DRYER HATCH

WASH TUB LID

Be sure to keep the lid

closed during washing

and spinning.

CONTROL LEG

Adjust the control leg

for even placement.

Otherwise,excessive vibration

and noise can occur

during spinning

OVER FLOW

FILTER

LINT FILTER

This is used for gathering

the dregs which are made

during washing.

WASH TUB

PULSATOR

The plug’s shape

may not correspond

with this drawing.

SPIN DRYER LID

Summary of content (5 pages)

PAGE 1
DESCRIPTION OF PARTS BEFORE USING THE WASHER SPIN DRYER LID When you open this lid while the spin basket is spinning, the spinning will be stopped by breake system. LINT FILTER OVER FLOW FILTER This is used for gathering the dregs which are made during washing. WASH TUB LID Be sure to keep the lid closed during washing and spinning. In case of pump drained washer, remove the cap-hose from the drain hole. ● CONTROL LEG Remove the cap-hose from the drain hose.
PAGE 2
CONTROL PANEL WASHING PROCEDURE SWT90C1(P) / SWT90C2(P) (A)Type SWT10H0(P) /SWT10H1(P) /SWT10H2(P) TO WASH Before starting washing, check the following 4.CYCLE SELECTOR 1.WATER SELECTOR During washing, WATER SELECTOR KNOB should be selected to wash. During spin rinsing, WATER SELECTOR KNOB should be selected to spin. This is used to set the Washing/Rinsing or Draining. (A)Type 5. SPIN DRY TIMER 2.WASH TIMER This is used to set the spin time 1-5 minutes.
PAGE 3
WASHING PROCEDURE OVER FLOW RINSE SPIN DRY 1. Transfer the clothes into the spin basket and arrange the clothes evenly. 3. Close the spin dryer lid. 2. Be sure to attach the safety cover and close the inner lid. (A)Type (B)Type 1. Keep suppling water(adjust water pressure 1. Keep suppling water(adjust water pressure to ensure that the amount of water supplied does not exceed that water drained.) to ensure that the amount of water supplied does not exceed that water drained.) 4.
PAGE 4
LAUNDRY GUIDE INSTALLATION AMOUNT OF CLOTHES ENVIRONMENT CHANGING THE POSITION OF THE DRAIN HOSE Before attempting to change the position of the drain hose, disconnect the plug from the outlet. 1. Route the drain hose inside the machine. 2.Take out the drain hose from the opposite hole and insert the drain hose into the hose holder. Leave some space Space at last 15cm between the washer and the wall. Place the washer on a sturdy flat surface.
PAGE 5
Owner’s Instructions IF YOU NEED HELP. Do not hesitate to call your local samsung service center. They will be willing to help you. Be sure to give them your name,address,telephone number and the purpose of the call. SW-903(P)/SWT90C1(P) / SWT90C2(P) SWT10H0(P) /SWT10H1(P) /SWT10H2(P) Before operating the unit, please read this manual throughly, and retain for future reference.