SSA-R2001 RFID Reader User Manual imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please visit our website. www.samsungsecurity.
safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire. 6. Install it in a place with good ventilation. 7. Avoid aiming the controller directly towards extremely bright objects such as sun. 8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. 9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
contents PRODUCT INTRODUCTION 5 INSTALLATION AND EXTERNAL CONNECTION 8 INITIALIZATION 11 OUTPUT FORMAT 13 TROUBLE SHOOTING 5 5 6 7 7 Features What’s included At a Glance Cable Color Scheme Cable Selection 8 9 10 Installation Precautions on installation External Connection 11 12 Output Format Basic Operations 13 14 15 WIEGAND Output RS-232 Output 4/8 BIT BURST Output Format 16 Trouble Shooting 17 Product Specification 16 PRODUCT SPECIFICATION 17 4_ Contents
product introduction FEATURES This product is an elegant-looking proximity reader equipped with the built-in keypad, which has the maximum of 10cm (4”) read range. It is also supported by backlighting on the keypad, enabling stable operation at night. This product permits user access through authentication of the contactless card and personal identification number using the keypad. Red, green and orange LED indicators and the built-in buzzer ensure reliable and accurate operations.
product introduction AT A GLANCE Front/Rear 6 X Y Z [ \ ] ^ _ ` lzj W lu{ 7 5 4 8 zzhTyYWWX 1 LED Displays the status of the system operation. 2 Keypad Used to enter the ID/password. 3 2-PIN Connector Can be connected to the power cable. 4 6-PIN Connector Can be connected to Wiegand, RS-232 communication cables. 5 8-PIN Connector Connected to the tamper, LED and buzzer control connection cables.
CABLE COLOR SCHEME ❖ 2-PIN Connector I/O Pins Signal Cable Color DC +12V Red Earth-grounding GND (-) Black PRODUCT INTRODUCTION Power (+12V) ❖ 6-PIN Connector I/O Pins Signal Cable Color Wiegand Data Output 0 WIK_DATA0 Green Wiegand Data Output 1 WIK_DATA1 White Not Used Not Used Orange RS-232 TX TX OUT Purple Not Used Not Used Brown RS-232-GND GND Black ❖ 8-PIN Connector I/O Pins Signal Cable Color Tamper Switch NC Tamper NC Green with White Stripes Tamper Switch COM T
installation and external connection INSTALLATION 1. Attach the provided rear panel to the wall and drill two 6-32 holes and one 1/2 inch hole on it. (See [Figure 1]) 2. Refer to [Figure 2] below on how to secure the rear panel to the wall using the provided screws. 3. Apply each of 5 O-rings to the corresponding point as shown in [Figure 2]. 4. Fix the main unit with the rear panel by inserting the main unit’s cables into the center hole and pushing the main unit towards the rear panel.
PRECAUTIONS ON INSTALLATION IF INSTALLING ON A METAL WALL Metal Wall Z X Y [ \ ] _ ` ^ lzj W lu{ yYWWX zzhT Spacer Reader IF INSTALLING MORE THAN ONE READER SIDE BY SIDE OR FRONT AND BACK If you install more than one reader side by side or front and back, the read range may be reduced. In this case, if you present a card to one reader, the other reader may recognize the same card, meaning both readers read the same card simultaneously.
installation and external connection EXTERNAL CONNECTION WIRING DIAGRAM SSA-R2001 Green Wiegand Data 0 Out White Wiegand Data 1 Out Green with white stripes X Y Z Tamper Switch Out(COM) Gray [ \ ] Buzzer Control In Blue ^ _ ` lzj W lu{ Tamper Switch Out(NC) CONTROLLER LED Control In(Red) White with red stripes LED Control In(Orange) PC RS-232(GND) Yellow LED Control In(Green) RS-232(TX) Purple Black zzhTyYWWX Blue with white stripes Red Black DC +12V GND POWER Category
initialization OUTPUT FORMAT You can adjust the output format of the numeric values from the keypad. You can select 4/8 bit Burst or 34bit Wiegand. Adjust the format according to the controller receiving the keypad input. 2. See the table below to make adjustment as needed.
initialization BASIC OPERATIONS Initial State (when the power is supplied) When you apply power to the product, it will sound beep three times before entering Standby with the red indicator turned on. Using the card CX Y ar d\ [ Z ] X Y [ Z \ ^ ] i _ lzj _ ` lzj W lu{ ` ^ W lzj zzhTzYWWW Present the card to the product until you hear a beep and the green indicator turns on. The reader keeps the green indicator turned on while transferring the card data to the controller.
output format WIEGAND OUTPUT Timing Diagram 5V 1ms DATA-0 0V 5V DATA-1 LOGIC 1 2 3 n-2 n-1 0 1 1 1 0 0V n *n : 34 or26 0 Data Format (34-bit) • Bit 1 : Even Parity (bit 2 ~ bit 17) • Bit 2~Bit33 : 4-byte ID Number • Bit 34 : Odd Parity (bit 18 ~ bit 33) English13 OUTPUT FORMAT 100us
output format RS-232 OUTPUT Output Waveform LSB +15V 0 1 MSB 0 0 0 0 0 1 0 Space(=0) +3V Indeterminate Region 0V -3V Mark(=1) 8 Data Bits -15V 2 Stop Bits Start Bit Data packet corresponding to ASCII character ‘A’ Data Type M START (0X02H) DATA (10 Char) END (0x03H) LRC START(0X02H) DATA (10 Char) END (0x03H) LRC Check the following settings: Baud Rate : 9600bps Data Bit : 8 Parity Bit : None Stop Bit : 1 LRC : This is the result of XOR operation of each byte from Start to
4/8 BIT BURST OUTPUT FORMAT 4Bit Burst Output Format Binary Hexa Keypads Binary Hexa 0 0000 0 6 0110 6 1 0001 1 7 0111 7 2 0010 2 8 1000 8 3 0011 3 9 1001 9 4 0100 4 ESC 1010 A 5 0101 5 ENT 1011 B 8Bit Burst Output Format Keypads Binary Hexa Keypads Binary Hexa 0 11110000 F0 6 10010110 96 1 11100001 E1 7 10000111 87 2 11010010 D2 8 01111000 78 3 11000011 C3 9 01101001 69 4 10110100 B4 ESC 01011010 5A 5 10100101 A5 ENT 01001011
troubleshooting TROUBLESHOOTING If the product does not function properly, please see the below for trouble shooting. If the trouble persists, please contact the SAMSUNG Customer Service near you. PROBLEM SOLUTION My card is not read properly. 1) 2) Check the rated voltage specified in the user manual and the catalog. Ensure that you are using an ISO14443 Type A card. - Cards of 125 kHz format can not be used. However, the 13.56 MHz card can not be used if it is of Type B, ISO15693.
product specifications PRODUCT SPECIFICATIONS Item SSA-R2001 Power / Current DC 12V / Max.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
