RFID Reader User Manual SSA-R1000V SSA-R1100V
RFID Reader User Manual Copyright ©2010 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document.
safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING • To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. WARNING 1.
safety information FCC Statement Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.
contents PRODUCT INTRODUCTION INSTALLATION AND EXTERNAL CONNECTION 9 INITIALIZATION Features What’s included At a Glance Cable Color Scheme Cable Selection 9 10 11 Installation Precautions on installation External Connection 12 Basic Operations 13 14 WIEGAND Output RS-232 Output 15 Troubleshooting 16 Product Specifications 12 OUTPUT FORMAT 13 TROUBLESHOOTING 15 PRODUCT SPECIFICATIONS 16 EnglisEnglish _ 5 CONTENTS 6 6 6 7 8 8
product introduction FEATURES This model is an elegant-looking proximity reader that can be easily attached to a metal doorframe or the wall. Featured by the epoxy adhesion and aluminium case, R1000V/R1100V is shock-resistant with a high level of weather-proofing in any challenging weather conditions. The red and green indicators as well as the Piezo buzzer guarantee a stable and proper operation for you.
AT A GLANCE Front/Rear PRODUCT INTRODUCTION LED Displays the system operation status using red and green indicators. Buzzer Piezo buzzer. Connection Cable Used to connect to the power or I/O cable. Fixing Hole Fixing hole for wall-mounting. Tamper Switch A tamper switch to detect falling from the wall.
product introduction CABLE COLOR SCHEME Item Cable Color Signal Line Description Red DC +12V DC +12V supplied Black GND Earth-grounding for power Blue Buzzer Control BUZZER Control Input Port Yellow LED Control LED Control Input Port Green Out Wiegand 0 Wiegand Data 0 Output Port White Out Wiegand 1 Wiegand Data 1 Output Port Communication Brown RS-232(TX) RS-232 Transmission Output Port Not used Orange NC Not Connected Pink Tamper Output (COM) Tamper Output Port Light yello
installation and external connection INSTALLATION - Inserted in the doorframe / attached to the wall 2. Insert the reader cables to the midway hole and fix the reader module with two 6-32 or M3 screws. 3. Insert the reader module into the appearance case and tighten the screw (M6x8mm) using the hex wrench. Upper 6-32 hole 1.7” (4.31cm) 3.3” (8.
installation and external connection PRECAUTIONS ON INSTALLATION If installing on a metal wall If you install the reader on a metal wall, the read range may be reduced. To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown below. Metal Wall Spacer Reader If installing more than one reader side by side or front and back If you install more than one reader side by side or front and back, the read range may be reduced.
EXTERNAL CONNECTION Wiring Diagram SSA-R1000V/SSA-R1100V Blue LED Control In CONTROLLER RS-232(TX) Brown RS-232(GND) Black Yellow Wiegand Data 0 Out Green Wiegand Data 1 Out White Tamper Output(COM) Tamper Output(NC) PC Pink Light yellow Red Black DC +12V GND POWER Item Cable Wiring Connect the DC+12V to the red line. Power Supply Unit Connect GND to the black line. Connect the green line of the product to the Wiegand D0 input port of the controller.
initialization BASIC OPERATIONS Initial State (when the power is supplied) When you apply power to the reader, it will sound a beep before entering Standby with the red indicator turned on . Using the card Present the card to the reader until you hear a beep and the red indicator turns green. When the reader has transferred the card data to the controller, it returns to Standby with the red indicator turned on and waits for reading the next card.
output format WIEGAND OUTPUT Timing Diagram 5V 1ms DATA-0 0V 5V DATA-1 LOGIC 1 2 3 n-2 n-1 n 0 1 1 1 0 0 0V *n : 26 Data Type • • • • Bit 1 : Even Parity (bit 2 ~ bit 13) Bit 2 ~ 9 : Facility Code (000 ~ 255) Bit 10 ~ 25 : ID Number (00000 ~ 65,535) Bit 26 : Odd Parity (bit 14 ~ bit 25) EnglisEnglish _ 13 OUTPUT FORMAT 100us
output format RS-232 OUTPUT Output Waveform LSB +15V 0 1 MSB 0 0 0 0 0 1 0 Space(=0) +3V Indeterminate Region 0V -3V Mark(=1) 8 Data Bits -15V 2 Stop Bits Start Bit Data packet corresponding to ASCII character ‘A’ Data Type M Start (0X02H) Data (8 Char) End (0x03H) LRC START(0X02H) DATA (1~8 Char) END (0x03H) LRC Check the following settings: Baud Rate : 9600bps Data Bit : 8 Parity Bit : None Stop Bit : 1 LRC: This is the result of XOR operation of each byte from Start to E
troubleshooting TROUBLESHOOTING If the product does not function properly, please see the below for trouble shooting. PROBLEM 1) 2) 3) When I turn on the product, it sounds a beep with dimly turned on indicator. 1) 2) 3) Check the rated voltage specified in the user manual and the catalog. Ensure that the card must comply with the PSK (125 KHz Proximity ) format provided by Samsung. Cards of 125 kHz purchased from other manufacturers may not be supported.
product specifications PRODUCT SPECIFICATIONS Item SSA-R1000V SSA-R1100V Power / Current DC 12V / Max.120mA Reading Time (Card) 30ms Input Port 2ea : External LED Control, External Buzzer Control Output Port 26bit Wiegand LED Indicator 2 Color LED (Red and Green) Beeper Piezo Buzzer Operating Temperature -30°C to +50°C Operating Humidity 10% to 90% relative humidity non-condensing Color / Material Silver with Black/Polycarbonate & Aluminum Die casting Dimension (W x H x D(mm)) 47.
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 www.samsungcctvusa.com www.samsungsecurity.com www.samsungtechwin.com SAMSUNG TECHWIN EUROPE LTD.
