SR20J9250U✴ Series POWERbot user manual ✻ Before operating this unit, please read the instructions carefully. ✻ For indoor use only. English imagine the possibilities Thank you for purchasing a Samsung product. SR9200J_EN_DJ68-00732B-00.
Contents 03 Safety information 08 Installation Accessories / Installation note 10 Charging Automatic charging / Recharging / Low battery (Lo) the Virtual guard 12 Installing Part name of the Virtual guard / Inserting batteries POWERbot 14 Using Selecting cleaning mode the remote control 16 Using Power/Recharging / Suction power / Additional function / Manual clean mode & Direction control / Point cleaning 18 Name of each part Top / Bottom / Display panel 19 Setting time/schedule Setting the time / Se
Safety information Safety information • Before operating the appliance, please read this manual thoroughly and retain it for your reference. • Because these following operating instructions cover various models, the characteristics of your vacuum cleaner may differ slightly from those described in this manual. WARNING WARNING CAUTION/WARNING SYMBOLS USED WARNING caution Indicates that a danger of death or serious injury exists. Indicates that a risk of personal injury or material damage exists.
Safety information Important safety instructions When using an electrical appliance, basic precautions should be observed, including the following: READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot. Unplug from outlet when not in use and before conducting maintenance. WARNING: to reduce the risk of fire, electric shock, or injury: GENERAL • Use only as described in this manual. • Do not operate POWERbot or charger (station) if it has been damaged in any way.
POWERbot • Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc. • Do not use without a filter in place. When servicing the unit, never put fingers or other objects into the fan chamber in case the unit accidentally turns on. • Do not put any objects into openings. Do not use with any openings blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow. • Do not pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).
Safety information WARNING ffDo not spill any liquids on the charger. Power related –– There is a risk of fire or electric shock. ffPlease prevent any risk of electric shock or fire. –– Do not damage the power cord. –– Do not pull the power cord too hard or touch the power plug with wet hands. –– Do not use a power source other than 100 - 240 V~ and also do not use a multi outlet to supply power to number of devices at the same time. (Do not leave the cord carelessly on the floor.
CAUTION Before use CAUTION ffInsert the dustbin before using POWERbot. ffOpen room doors before cleaning in order to have all rooms cleaned and install a Virtual guard in front of entryway, balconies, bathrooms, or other areas where POWERbot may fall. ffBe careful with the followings for proper automatic recharging. –– Always turn on the power of the charger. –– Install the charger where POWERbot can easily find. –– Do not leave any object in front of the charger.
Installation Power of the charger must be on at all times. Do not install the charger in a narrow passage or near a door. Install it in a place without obstacles and danger of falling. Power lamp (Red) t1 u bo m A Abo ut 0. 5m DC-IN Abou t 0.5 m DC-IN 1 Connect the adapter jack to the charger 2 Connect the power cord to the adapter When using the adapter, the side with the sticker attached must face down. 3 Connect the power plug to the outlet Power lamp (Red) will turn on.
Accessories Remote control Batteries (AAA type) User manual Spare filter Cleaning brush Power cord Adapter Virtual guard Installation note Note ffInstall charger in a place where the floor and wall are level. ffIt is best to install the charger along the grain of wooden floors. ffIf the emergency switch is off, POWERbot will not charge even if it is docked on the charger. ffAlways turn on the power of the charger.
Charging It takes approximately 160 minutes to completely charge when charging for the first time after purchase and can be used for approximately 30 minutes in Max mode. WARNING • Rated input voltage of this product is 100 - 240 V~. Charging lamp during charging (green) 1 Turn on the emergency switch on the bottom You must turn on the emergency switch to turn on POWERbot. 2 Manually charge POWERbot by placing it on the charger Make sure charge pins of POWERbot and the charger is aligned.
Automatic charging When the battery indicator blinks during cleaning, POWERbot will return to the charger to charge itself automatically. Recharging You may command POWERbot to recharge at the charger while it is in cleaning process. Low battery (Lo) Manually charge POWERbot by placing it on the charger.
Installing the Virtual guard Infrared ray from the Virtual guard will restrict POWERbot from approaching certain area. The distance of virtual wall is 2.5 m at minimum and may differ depending on surroundings and movement status of POWERbot. Virtual guard .5 m 2 um im Min 1 Press the Power button to turn it on Power lamp (Red) will blink.
Part name of the Virtual guard Power button POWERbot detection sensor Power lamp Power on: Red lamp blinks Power off: Lamp is off Distance detection sensor (Infrared ray sensor) Battery cover Inserting batteries Batteries for Virtual guard must be purchased separately. 1 Open the battery cover of the Virtual guard by pressing the locking tab and lift it up. 2 Insert the alkaline batteries (D type) as shown in the illustration (check the +, - polarity).
Using POWERbot You must turn on the emergency switch before using POWERbot. Turning the power on/off Press the 3 second button for more than WARNING • When POWERbot is not used for 30 minutes, it will return to the charger to charge itself automatically. Using Auto clean mode The POWERbot moves and cleans automatically until it cleans entire space once. ✻✻Stop cleaning: Press the button Using Spot clean mode The POWERbot cleans a localized area intensely.
Selecting cleaning mode Cleaning mode How to select Displayed icon Auto clean Spot clean ✻✻Spot clean mode can be selected only by pressing this button on the main body of the POWERbot. Manual clean ✻✻Manual clean mode can be selected by the direction control buttons of the remote control. ✻✻When cleaning is done within 15 minutes in Auto clean mode, the POWERbot will repeat cleaning one more time. ✻✻When dust intake is detected in Spot/Manual clean mode, suction of the POWERbot will become stronger.
Using the remote control 1 Power / Recharging / Start/Stop Power Recharging Start/Stop Turn POWERbot's power on/off Select to recharge POWERbot at the charger automatically Select to start or stop cleaning process 2 Suction power Max mode Normal mode Quiet mode Select to clean with the strongest suction power Select to clean with moderate suction power Select to clean with lower operation noise 3 Additional function Sound Remote control Each time you press this button, Sound Effects → Mute is select
1 4 Manual clean mode & Direction control Select to move forward 2 1 4 5 3 Refer to page 19 Select to turn left Select to turn right ✻✻Moving backward is not available. 5 Point cleaning You can use the remote control to point and clean the desired spot while the POWERbot is in cleaning process. Point the red light on the floor within 1 m around POWERbot's location. Press and hold the Point cleaning button to move the red light to the desired spot. The POWERbot will follow the light while cleaning.
Name of each part Top 1 3 2 3 6 4 7 8 4 3 5 9 1 4 2 7 3 4 4 5 8 6 9 1. 2. 3. 4. 5. 6. 7. 8. 9. Display panel Dustbin holder Remote control signal receiver Virtual guard sensor Obstacle sensor Dustbin Camera Dustbin handle Bumper sensor Bottom 1. 2. 3. 4. 5. 6. 7. 8. 9. Charge pins Power brush Power brush cover Cliff sensor Roller Battery cover Power brush cover button Driving wheel Emergency switch 5 3 4 1 5 2 6 8 7 9 10 15 11 12 13 14 16 17 Display panel 1. 2. 3. 4. 5. 6.
Setting time/schedule Only Auto clean mode can be scheduled. Setting the time You must set the current time before using the One-time/daily schedule. Start setting Select "Hour" Select "Minute" Setting complete Select "AM/PM" Skip to previous, next setting Setting the schedule Setting/cancelling the schedule can only be done while POWERbot is docked on the charger.
Cleaning and maintaining You must turn off the emergency switch before cleaning POWERbot. Cleaning the dustbin Clean the dustbin when filter inspection indicator ( 1 Remove the dustbin 2 ) turns on or if there's too much dust in the dustbin.
Cleaning the Power brush Remove the Power brush cover 4 Reassemble the Power brush 2 Remove the Power brush 5 Reassemble the Power brush cover 3 Clean the Power brush ON OFF 1 ON OFF Cleaning the Driving wheel 1 Put a soft cloth on the floor and place POWERbot upside-down. 2 Use a blunt rod or tweezers to remove the foreign matters. ENGLISH-21 SR9200J_EN_DJ68-00732B-00.
Samsung Smart Home App Preparing the network Setting up the wireless router fThis f product supports only DHCP(Dynamic Host Configuration Protocol). Please check if the DHCP server option function of a wireless router is activated. fThe f supported types of authorization/encryption of the wireless router are WEP-OPEN, WPA-PSK/TKIP and WPA2-PSK/AES 801.11n. –– WPA2-PSK/AES is recommended to be used.
ffIf the POWERbot and smart phone are not connected to the same wireless router, response delay may occur according to network environment. ffRemote lock and Wi-Fi indicator –– On : Remote control is locked. –– Off : Remote control is allowed. –– Off : The POWERbot is connecting to the wireless router. –– On : The POWERbot is connected to the wireless router.
Samsung Smart Home App Registering the product (Easy-Setup) Register the product to the Samsung Smart Home Service before using the Samsung Smart Home app. 1. Press the Add new icon on the device list screen of the Samsung Smart Home app to start the registration of the product. 2. Select the Robot vacuum icon. 3. Enter the information of the wireless router to be connected. 4. Set the POWERbot according to the guidance on the screen.
Downloading Samsung Smart Robot vacuum app You can use more diverse functions through the Samsung Smart Robot vacuum App, which is exclusively for the POWERbot. 1. Select the Robot vacuum icon on the device list screen of the Samsung Smart Home app. If the Samsung Smart Robot vacuum app is not installed, you will be moved to the Google Play Store automatically. 2. Install the Samsung Smart Robot vacuum app. 3.
Samsung Smart Home App Main screen fSelect f the Robot vacuum icon on the main screen, and you can move to the POWERbot control screen. fYou f can control your smart home appliances made by Samsung Electronics by Going out, Coming home, Good night, and Good morning icons. fHome f view function is not supported for a POWERbot. User menu screen fYou f can control the smart home appliances made by Samsung Electronics with Chat control and Master key functions.
Controlling POWERbot When accessing the Samsung Smart Robot vacuum app, the control screen will appear. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
Notes and cautions ffThe POWERbot cannot vacuum clumps of dirt, so some may remain on the floor after cleaning. Charging Note ffIf the battery overheats during charging, it may take longer to charge. ffWhen automatic charging is not working, please check the followings. –– Turn the emergency switch (on the bottom of POWERbot) off and on again. –– Unplug the charger's power plug and then plug it back on.
About battery About the IrDA sensor Caution Note ffPurchase batteries at service centers and ) and check the genuine part symbol ( model name before purchasing. ffThe infrared signal transmission may not be smooth in locations exposed to halogen lamps or in outdoor locations. ffThis battery is exclusive for Samsung Electronics POWERbot; do not use it for any other product. ffThe POWERbot uses 3 types of infrared devices and a device may not work in front of another device with a higher priority.
Information codes 1 Below information codes appear on the display panel 2 Turn off the emergency switch and check the below instructions and take appropriate action Information codes 3 Information code will disappear when you turn on the emergency switch Checklist The POWERbot is caught, stuck or trapped while moving around. fTurn f off the emergency switch and move the POWERbot to another area. Foreign matter caught in the Power brush.
Troubleshooting Symptom The POWERbot is not working at all. Checklist fCheck f if the emergency switch is on. fCheck f if all the icons are displayed on display panel. fCheck f if the battery of POWERbot is depleted. –– When "Lo" is displayed, carry POWERbot to the charger to charge it. fReplace f the batteries (AAA type) when the remote controller is not working. The POWERbot is stopped during cleaning process. fWhen f "Lo" is displayed on the display panel, carry POWERbot to the charger to charge it.
Troubleshooting Symptom Checklist POWERbot moves around at the same place. fDust f sensor mode is on. –– The dust sensor mode is on by default. When the POWERbot passes through a dusty area, it moves around that area to focus on cleaning. fPOWERbot f moves around an area and the "DUST" is on the display panel even though there's no dust at the surrounding area. –– Check if foreign matters are caught between the dustbin and power brush and then remove them. POWERbot does not clean a certain area.
Open Source Announcement The software included in this product contains open source software. You may obtain the complete corresponding source code for a period of three years after the last shipment of this product by sending an email to mailto:oss.request@samsung.com. It is also possible to obtain the complete corresponding source code in a physical medium such as a CD-ROM; a minimal charge will be required. The following URL http://opensource.samsung.
Specifications Classification Mechanical specifications (POWERbot) Power specifications Item Detail information Size (Depth x Height x Length) 378 mm x 135 mm x 362 mm Weight 4.8 kg Sensor Ceiling shape recognition (Visionary mapping plus TM) Button type of POWERbot Touch type Power voltage 100 - 240 V~, 50 Hz / 60 Hz Power consumption 180 W (Max mode) Battery specifications Lithium ion 21.
Note ENGLISH-35 SR9200J_EN_DJ68-00732B-00.
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. Country Customer Care Center Web Site U.K 0330 SAMSUNG (7267864) www.samsung.com SOUTH AFRICA 0860 7267864 (SAMSUNG) www.samsung.com AUSTRALIA 1300 362 603 www.samsung.com HONG KONG (852) 3698-4698 www.samsung.com/hk www.samsung.com/hk_en/ MALAYSIA 1800-88-9999 www.samsung.com SINGAPORE 1800-SAMSUNG (7267864) www.samsung.
