EZ View Kit:Remote Monitoring Video Surveillance SYSTEM SMO-211QN, SMO-150QN User Guide
IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these Instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Graphic Symbol Explanation The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated ‘dangerous voltage’ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
IMPORTANT SAFEGUARDS Caution Power source is indicated on the rear of the set. It contains high-voltage parts. If you remove the cover, it may cause fire or electric shock. Do not remove the cover by yourself. (Control switches are at the front of the monitor.) 1. Read Instructions : All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions : The safety and operating instructions should be retained for future reference. 3.
8. Accessories : Do not place this monitor on an unstable cart, stand, tripod, bracket. The monitor may fall causing serious injury to a child or adult and serious damage to the appliance. Use only with a cart, stand, tripod, bracket or table recommended by Samsung or sold with the monitor. Any mounting of the monitor should follow Samsung’s instructions and should use a mounting accessory recommended by Samsung. 9.
13. Lightning : For added protection for this monitor during a lightning storm or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the monitor due to lightning and power-line surges. 14. Overloading : Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. 15.
18. Replacement Parts : When replacement parts are required be sure the service technician has used replacement parts specified by Samsung or have the same characteristics as the original parts. Unauthorized substitutions may result in fire electric shock or other hazards. 19. Safety Check : Upon completion of any service or repairs to this monitor ask the service technician to perform safety checks to determine that the monitor is in proper operating condition.
Information to user Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
The party responsible for product compliance: SAMSUNG ELECTRONICS CO., LTD. America QA Lab of Samsung 3351 Michelson Drive, Suite #290, Irvine, CA92612 USA IC Compliance Notice This Class (A) digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe (A) respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This Class A digital apparatus complies with Canadian ICES-003.
Contents IMPORTANT SAFETY INSTRUCTIONS .................................. 2 IMPORTANT SAFEGUARDS..................................................... 4 FCC & ICES Information.............................................................. 7 Chapter 1: System Components and Installation 1-1) Environmental requirements for installation and safety .......... 12 1-2) System Components.............................................................
2-14) UP/DOWN KEY............................................................... 35 2-15) LEFT/RIGHT KEY........................................................... 35 Chapter 3: Setting each item function in the SETUP MENU 3-1) ADJUST MENU Function and setting method ................... 36 3-2) DATE/TIME MENU Function setting ................................ 37 3-3) DWELL TIME MENU Function setting ............................. 37 3-4) DISPLAY MENU Function setting ....................................
Chapter 1: System Components and Installation 1-1) Environmental requirements for installation and safety This section describes the environmental requirements for safe installation and use. Install the product on a flat table or in a rack. It should be used only when level and should not be used when stood vertically or obliquely. The location in which the main system is installed and the configuration of the wiring room are very important for proper operation of the system.
1-2) System Components The system consists of the following: STANDARD CAMERA (SOC-C120) MONITOR POWER CORD & INSTALLATION MANUAL CAMERA BRACKET DOME CAMERA (SOC-D120) PIR CAMERA (SOC-P120) CAMERA CAMERA Corner Mount CABLE BRACKET VCR CABLE SENSOR CONNECTOR ETHERNET CABLE ITEM MODEL MONITOR SMO-211QN 21" FLAT CRT MONITOR 1 AB97-00793A SMO-150QN 15" FLAT CRT MONITOR 1 AB97-00787A SOC-C120 WR(Standard) Camera 2 AB97-00720A SOC-D120 DOME Camera 1 AB97-00721A SOC-P120 PIR Camera 1
1-3) STANDARD CAMERA composition and installation method 1) Standard Camera composition (SOC-C120) PIN NUMBER SPEC ! SPEAKER(HOT) @ VIDEO_OUT # GND $ SPEAKER(COLD) % AUDIO_OUT/ALARM_OUT ^ 18V DC a. Lens It has a focal length of 3.8mm and makes it possible for you to observe a relatively wide area. b. Microphone Capable of picking up all sound in the vicinity of the camera location and transmitting to the monitor. c.
f. Speaker Outputs the sound signal. 2) INSTALLING STANDARD CAMERA (SOC-C120) SOC-C120 camera can be attached to the wall, ceiling or shelf using the camera mount bracket (SBR-110S). Choose an installation site that can sufficiently support the weight of the equipment to be installed. Attach the camera mount bracket to the wall or ceiling using the supplied three screws (M4 X L15). Adjust the camera to target the video location and tighten the bracket handle on the camera mount bracket.
3) CAMERA MOUNT BRACKET(SBR-110) & STANDARD CAMERA(SOC-C120) (1) Overview CAMERA MOUNT BRACKET (SBR-110S) is used to attach the camera to a wall, ceiling or shelf. (2) Specifications Use : Indoor Installation : Wall or Ceiling Dimensions : 2.25 (W) X 1.86(H) X 3.95(L) inch Weight : 0.29 lbs Operating Temperature : 32°F ~ 104°F (3) Accessories SCREW (M4 X L15) : 3 pcs (4) Installation Explains the installation of CAMERA MOUNT BRACKET as well as the installation of the camera onto the CAMERA MOUNT BRACKET.
• Adjust the camera to target the video location and tighten the bracket handle on the camera mount bracket. Install the camera on to the male screw of the Camera Mount Bracket by rotating the camera clockwise. • Loosen the handle by turning it in a counter clockwise direction and then adjust the camera position . Tighten the handle, turning it clockwise, and lock the camera in position. • Connect the camera cable to the camera.
After positioning the monitor and installing four cameras in the desired location, please connect the CAMERA to the MONITOR using the CAMERA CABLE (MCB-60) as shown in the figure below. Connection status checking method : • Turn on the monitor after connecting cameras, and check if camera image is displayed. The monitor's initial screen mode is quad. • In the monitor and the camera are not connected properly, OSD ‘L’(LOSS) will be displayed on screen.
1-4) DOME CAMERA composition and installation method (SOC-D120) 1) Dome Camera composition (SOC-D120) a d b e c PIN NUMBER SPEC 1 N.C 2 VIDEO_OUT 3 GND 4 N.C 5 N.C 6 12V DC ✽ Fixed Dome Camera does not have aspeaker,so the alam and !@#$%^ audio features are not supproted. a Fixed Focus Lens Keeps the camera's lens free from dust and dirt. b Lens Assembly c Camera Frame Supports the camera. d Dome Cover Clear plastic cover that protects the camera. Take care not to scratch the cover.
2) INSTALLING THE DOME CAMERA (SOC-D120) • Attach the camera to the wall or ceiling using the supplied tap screws. • Put the dome cover back on the camera by rotating the cover clockwise. Wall or ceiling Main body Screw Driver Tab screw • Adjust the video location by swiveling the camera (Lens assembly) up and down, and adjust the focus by turning the lens clockwise and counter clockwise.
1-5) PIR CAMERA composition and installation method (SOC-P120) 1) PIR Camera composition (SOC-P120) 1> Vertical Detection Line 3 5 4 1 • Please consider the horizontal detection area and the vertical detection line when choosing an installation site.
6 8 ON 7 9 OFF ! PIN ! @ # $ @ # $ Function Sensor Sensitivity On, On : Low On, Off : Normal Off, On : Normal Off, Off : High Alarm LED On/Off (Sensor On) Sensor On/Off ➅ Function Switch A function switch for the PIR sensor operation. ⑦ PIR Sensor A thermal heat sensor that detects infrared radiation projected by warm objects. ⑧ Microphone Capable of picking up all sound in the vicinity of the camera location and transmitting to the monitor.
2) INSTALLING THE PIR CAMERA (SOC-P120) Assy-case front 1. Choose an installation site that can sufficiently support 5 times the weight of the equipment to be installed. 2. Remove the screw (BH M2.6) at the bottom of the main unit by turning it counterclockwise, and then lift the assy-case front as you push it upward to detach it from the case-rear. (❊ Do not apply excessive force, as doing so may damage the internal assembly.❊) 3.
5. Align the two holes of the caserear to the holes of the plastic anchors, and then fasten the screw tappings (BH M3 X 30). 6. Adjust the direction of the lens. 1) Use a the philips head screwdriver to turn the screw (indicated by the arrow in the illustration) counterclockwise slightly. The lens body will move. 2) Tilt the lens body down about 10° from the horizontal, and then turn the screw clockwise to fasten it. SCREWTAPPING G(BH M3 x 30) SCREW-TAPPING G(BH M3 x 30) 7.
3) INSTALLING THE CAMERA USING THE CORNER MOUNT(SOC-P120) 1. Choose an installation site that can sufficiently support 5 times the weight of the equipment to be installed. 2. Place the corner mount to the corner to which you want to install the camera and mark screw holes with a pencil (indicated by the circles in the illustration). Drill a pilot hole for each pencil mark (0.2 inch in diameter and at least 1.38 inch in depth), and then fully insert the supplied plastic anchors (HUD 5) into them.
5. Connecting Cables 1) Connecting the RJ-11 cable to the RJ-11 connector on the case-rear and connect the camera cable to the cable terminal on the case- rear. 2) Pass the cables through the hole on the corner mount as shown in the picture to the right. 6. Assemble the case-rear onto the corner mount by aligning the two holes of the case-rear to the protrusions of the corner mount and fasten the screw-tappings (PH M3 X 16). 7. Adjust the direction of the lens.
CASE-REAR 8. Assemble the assy-case front onto the case-rear as shown in the illustration. Fasten the assy-case front to the case-rear with the screw (BH M2.6) you removed earlier. Screw (BH M2.6) 3) CABLE CONNECTION (SOC-P120) • Connect the camera cable to the camera cable jack on the camera, then connect the other end of the cable to the monitor's channel input jack as shown in the illustration. • Connect the alarm box to the terminal block, which is located on the bottom of the camera.
1-6) Camera and Monitor connections 1) External terminal connecting method for CAMERA Camera alarm in jack Sensor in put Sensor PIR Sensor • An additional PIR sensor or external sensor can also be connected. • The additional PIR sensor can be connected as shown in the illustration above. • Sensor’s trigger signal is NO (Normal Open). • Sensor is not supplied.
f) Not Used g) Connect the A/O (HOT) terminal on the rear panel to the Alarm IN terminal of the VCR. h) Connect the A/O (COLD) terminal on the rear panel to the Ground terminal of the VCR. i) Connect the A/R terminal on the rear panel to the Alarm Reset terminal of the VCR. j) Connect the G (ground) terminal on the rear panel to the Ground terminal of the VCR.
1-8)Total System Configuration Eng-30
1-9)Local System Configuration 1. Connect LAN cable of Cable/DSL modem or Direct Fixed/Static IP LAN Line to WAN port of IP Router. 2. Connect LAN ports of IP Router(1~4 or 1~8) to Ethernet port SMO-211QN/SMO-150QN to be set up and to Ethernet port of Local PC to use during setup. 3. Connect Video cable of Camera to MONITOR. 4. Turn on the MONITOR power.
Chapter 2: MONITOR FRONT PANEL KEY Function and Operation Front Panel 2-1) TALK KEY The TALK KEY allows voice signal tobe transmitted to an intended camera with built-in MIC on the front of the monitor. For this function, select a target camera with the ▲/▼ key on the FRONT PANEL, and press AUD/SP SEL KEY. At this time, if a voice signal is generated through the MIC with the TALK KEY pressed, the signal will be transmitted to the camera.
2-4) SCREEN SAVE - KEY Allows users to set the monitor's SCREEN SAVE MODE. The PICTURE screen is off when the SCREEN SAVE KEY is pressed. Users can exit from the SCREEN SAVE MODE by pressing the SCREEN SAVE BUTTON again. SCREEN SAVE MODE is automatically cancelled and picture is “ON” when an event such as an alarm or video loss in the SCREEN SAVE MODE occurs. 2-5) ALARM RESET- KEY Alarm function can be cancelled while the alarm is working.
2-8) PIP- KEY Can be used to see the main screen while Single screen is displayed. The main screen can be changed and transfered to another channel while in PIP mode. Please refer to "CHAPTER 4. DISPLAY MODE setting method(Eng-88)" for PIP function and details. 2-9) FREEZE- KEY This key allows users to see a target camera picture in the PAUSE MODE.Select a camera with the ▲/▼ KEYs and press the FREEZE button. All other controls are disabled while in freeze mode.
2-13) ENTER- KEY Enter key allows users to: 1.Enter set up menu and setting mode 2.Display single camera picture 2-14) UP/DOWN KEY Allows users to 1.Change camera channel 2.
Chapter 3: Setting each item function in the SETUP MENU Pressing the FRONT PANEL MENU button allows users to enter SETUP MENU and see the following menu OSD box. Setting method of each SETUP MENU function and operation is as follows. 06/01/03 SETUP 13:14:00 VE_1.07 MENU 1. ADJUST 2. DATE/TIME 3. DWELL TIME 4. DISPLAY 5. TITLE 6. ALARM 7. NETWORK SETUP 8. VIEW EVENT LOG 3-1) ADJUST MENU function and setting method • Function: Allows adjustment of the display status • Setting method: Move to #1.
3-2) DATE/TIME MENU Function setting • Function: Sets the display date format and current time. • Setting method: Move to #2. DATE/TIME MENU by using ▲/▼ KEY at setup menu, then press the ENTER SWITCH to display the OSD as shown in the below figure below. (The figure shows the initial setting status.) 06/01/03 DATE/TIME SETTING DATE TYPE DATE TIME [HH:MM:SS] • 13:14:00 MM/DD/YY 06 / 01 / 03 13 : 14 : 00 Setting method of date display format Move to the item by using ▲/▼ KEY, and press ENTER .
If the time is set for each camera channel by using ▲/▼ KEY, each camera picture will be displayed for the set time and switched to the next picture automatically. 3-4) DISPLAY MENU function setting • Function: Allows users to select the color and ON/OFF of borderline at QUAD DISPLAY. • Setting method: Move to #4. DISPLAY SETTING MENU by using▲/▼ KEY in the SETUP MENU, then press ENTER to display the OSD as shown in the below figure. (The figure shows the initial setting status.
3-5) TITLE MENU Function setting • Function: Set the desired title of each camera. • Setting method: Move to #5. TITLE MENU by using ▲/▼ KEY in the SETUP MENU, and press the ENTER SWITCH to display the OSD as shown in the figure below. (The figure shows the initial setting status.) 06/01/03 TITLE CAMERA1 CAMERA2 CAMERA3 CAMERA4 CAMERA5 CAMERA6 CAMERA7 CAMERA8 13:14:00 SETTING CAM1 CAM2 CAM3 CAM4 CAM5 CAM6 CAM7 CAM8 0 1 2 3 4 5 6 7 8 9 : = .
3-6) ALARM MENU Function setting • Function: Allows users to set the ALARM MODE for each camera. • Setting method: Move to #6. ALARM MENU by using ▲/▼ KEY in the SETUP MENU, and press the ENTER SWITCH to display the OSD as shown in the figure below. (The figure shows the initial setting status.
3-7) NETWORK SETTING function and setting method This section of the manual is intended for users who will install this security system in a network environment.If you have difficulty setting the network,we recommend contacting your network administrator. • Static • DHCP • DSL (PPPoE) • Function: Allows users to select the STATIC (fixed) IP, DHCP, PPPoE of Setting.
5) After setting, move to the main screen by using the MENU BUTTON. 6) Set values will be stored as shown below. It takes 2 or 3 seconds. 06/01/03 13:14:00 [S] 06/01/01 13:14:00 NETWORK SETTING CAM1 On completion of setting to Static IP(Fixed IP)setup, the screen, [S] is displayed. If the network connection is cancelled or cut, [S] starts blinking. 7) Open your Internet Explorer web browser.
DHCP User - Constituted by Dynamic IP on the cable/xDSL modem network You can use the SMO-211QN/SMO-150QN products through the network using Dynamic IP on cable/xDSL modem. In this case, it should be connected with DDNS to support the Dynamic IP. In case of a configuration using DHCP, as the connection to SMO-211QN/ SMO-150QN is made using domain names (EX : http://sff0000.websamsung.
2) Move to ‘DHCP...’ by using ▲/▼ KEY in NETWORK ACCESS, then press ENTER SWITCH to set to DHCP. 06/01/03 13:14:00 DHCP ACCESS DNS 1 DNS 2 168.126.63.001 168.126.63.002 3) DNS 1 and DNS 2 will be automatically set to DNS as shown above. Use œ / √ KEY to change it. 4) After setting, move to the main screen by using the MENU button. 5) Set values will be stored as shown below. It takes 2 or 4 seconds.
8) Open your Internet Explorer web browser, type in the following in the URL window and press Enter. http://sff0000.websamsung.net Where ff0000 is the MAC address of your SMO-211QN/SMO-150QN in this example. If your SMO-211QN/SMO-150QN’s MAC address is ff0001, then type in ff0001 instead of ff0000 * Note : MAC Address. Locate the MAC Address of the SMO-211QN/SMO-150QN (each SMO211QN/SMO-150QN has its own unique MAC address) It can be checked in ‘7.NETWORK SETUP” of SETUP MENU’.
DSL User (PPPoE) SMO-211QN/SMO-150QN products can be used on the network using IP through PPPoE (DSL). In case of a configuration using PPPoE, SMO-211QN/SMO-150QN connection is made through the domain names (EX : http://sff0000.websamsung.net) that are automatically registered in Samsung's DDNS server. You do not need to enter IP address, Subnet Mask and Gateway in the network tab of Admin Mode. 1) Connect as in the figure below and turn on the power of each piece of equipment in the following order.
06/01/03 13:14:00 PPPoE... ACCESS DNS 1 DNS 2 USER ID USER PWD 168.126.63.001 168.126.63.002 ******** ******** 4) When the PPPoE (DSL) type in the User Name and Password (and Confirm Password) given to you by the DSL Service Provider. CAUTION When using DSL (ISP-internet service provider) you must type correct User Name and Password to connect to SMO-211QN/SMO-150QN. If you type an incorrect User Name or Password, commection is impossible.
10) You can view the video source of the SMO-211QN/SMO-150QN from a remote location PC. 11) Make sure the remote PC meets the minimum specification requirements described in Chapter 5. Each product feature (Eng-91), and make sure that the PC is internet capable and set up to able to browse the internet. 12) Open your Internet Explorer web browser, type in the following in the URL window and press ENTER. http://sff0000.websamsung.
CAUTION The connection to SMO-211QN/SMO-150QN is unavailable for about 2~5 minutes after DSL Modem’s power ON. Since the connection is not available, as the IP is not received from DSL communications, please reboot by turning off the power of DSL Modem and SMO-211QN/SMO-150QN for more than 5 seconds,and then try to connect again. 3-8) SMO-211QN/SMO-150QN basic setting 1) Open your Internet Explorer web browser, type in the Monitor's IP address: http://sff0000.websamsung. in the URL window press ENTER.
4) Click YES . This will automatically download the necessary Active X Controls to operate the Remote Viewer. It takes about 20 seconds at the first connection. 5) When you enter properly, a window appears as shown below. Note:If the MPEG 4 codec is improperly installed, you will not see video images. To see video, click on Dual Quad Viewer in the upper left portion of the screen, then a window will appear prompting you to install MPEG 4.
3-8-1) “LIVE” MENU 2 - CAMERA SELECT 3 # % ! ^ * ( ) 1 @ $ & Initial display mode of monitor if QUAD A. - Remote Viewer Function Buttons KEY Type Function Choose a camera by channel Ch 1 ~ Ch 8 4 Cameras are supplied. You can connect ! 4 additional cameras if desired.
PLAY ) STOP 1 LIVE MODE change 2 ADMIN MODE change 3 - SINGLE SCREEN DISPLAY If users want to see the camera image at full mode,or smaller mode, Select a target camera with NEXT channel or CHANNEL SELECT keys. After camera selection, camera image can be displayed at full screen. * AT SINGLE DISPLAY Original Size Large Size - QUAD MODE DISPLAY A user can select the QUAD mode. QUAD A -> QUAD B -> QUAD A -> ...
- Auto SEQUENCY DISPLAY MODE Press the sequence key in the single or QUAD mode to display the screen in sequence. If the DWELL TIME SETTING of SETUP MENU is set to 3 seconds and the SEQUENCY KEY is pressed at this time, the operation will be carried out as follows. (NO signal channel will be skipped while single screen is auto-switching) * SINGLE MODE SEQUENCE DISPLAY -> Press SEQUENCY KEY When SINGLE MODE (camera select key) is displayed at full screen.
1. Recording When saving with Viewer, the file and folder are created automatically. If the Mac address of product is "00-30-6F-FF-00”, the created file and folder are as follows. "C:\Program Files\Samsung \SMO-211QN/SMO-150QN\00-30-6F-FF-00" An user can change the name of file or folder by use of the save key ( ) of Viewer. If you are connected to and recording from more than one SMO-211QN/SMO-150QN on the same PC, there will be more than one “Server Name” directory.
2. PLAY When you select play and double click the file, that file will play back on the Remote Viewer as a motion clip. You can select several files simultaneously at once (up to 10) and the files will be played back in the order of the file name (by date and time).
3. PLAYER - Player installation/execution/deletion - Installation Player will be installed together when it is connected to SMO-211QN/SMO-150QN. - Execution (Follow the instruction to execute it separately.) Click Start —> Program —> Smart Webviewer For WEB-MON —> Player. (Fig. 3 ) FIG.3 - Deletion Click Start —> Program —> Smart VIewer For WEB - MON —> Uninstall. (Fig.
- Program screen configuration - How to play 1. Playback File - Open... Selecting this, you can choose between fmp4(moving image file) or fmpi(still image file) in the window as shown below.
Having chosen and opened a file, you will see a picture as shown below. Reverse playback Enlarge Playback Reduce Pause Original size Stop Save the present frame as a image Print To the back frame To the front frame Status Display the playback speed, bar magnification, and information on the storage.
- Snap shot Save the present image as a form of fmpi file. Select in the toolbar. The result will be as follows. Type in the file name and press ‘Save’ to store it as a fmpi file. - Print Prints the present image. Select Eng-59 in the toolbar. The result will be as follows.
Type in the phrase you added in ‘Description’. Then press the ‘OK’ button. Select Print and press ‘OK’.
Admin Menu The following pages are geared towards advanced users who function as network adminidtrators, and will be using the system in a network environment. It is an administrator’s menu to set the general items on SMO-211QN/SMO-150QN Server. To use this menu, you need the administrator’s ID and Password. On delivery, they are “root” (administrator’s ID) / “root” (administrator’s Password). The password can be changed on Admin Menu.
-3) Type in the administrator and password in the user’s name and password columns and press Enter key to execute the Admin Menu as shown below. 1 2 4) Screen configuration ! : General menus of Admin Menu. The menus related to SMO-211QN/SMO-150QN Server are divided into System, Network, Monitor Setup, and Utilities in the main. Each of them has several sub menus.
• Admin Menu Structure Category System Configuration Main Menu System Information Admin.
3-8-2) System Configuration Menu. 1. System Information In this menu, you can check the information on the system including the name of the SMO-211QN/SMO-150QN Server. Server name can be changed if desired. - Menu Configuration Server Name Type in the name of the SMO-211QN/SMO-150QN Server. * Server’s name should be composed of 19 or less numerals or English alphabetical letters. It cannot start with a numeral and should start with a letter.
2. Admin Password In this menu, the administrator (root) password can be changed. - Menu Configuration Administrator’s ID Old Password Administrator’s ID is always “root”. The initial password is “root”. New Password Type the new password. * The password should be composed of 4-8 digit numerals or alphabets. Confirm Password Type the new password again. After completing setting, click Apply button. The new password will be applied. The user needs to log in again by using the new password.
3. Access Configuration This menu is to set the targets the SMO-211QN/SMO-150QN Server can have a access to. - Menu Configuration Access Limitation This is to set limit for the frame speed for users who are Configuration registered in the system, to join and view images. The users, who join in the system after this setting, will be connected at the set speed. The access speed can be set on the Local Network depending on the network status.
4. User Registration This is a user control menu to register, change, or delete the users who may have access SMO-211QN/SMO-150QN Server.
- Menu Configuration User ID Password Set the ID you want to register. Set the password you want to register. Confirm Type again the password you want to register. Password Full Name Type in the name you want to register. Add This is a menu to register a user. It is to fix the user’s ID, Password, name, and set the users accessibility of the system. - Type in the user’s ID in the User ID column. - Type in a password in the Password and Confirm columns.
5. Video Configuration This is to set the data to be added in the video configuration and set an environment for each channel. - Menu Configuration Image Size This is to choose the size of the video data image . You can choose between 2 size (Small / large). Image Quality This is to choose the image quality. You can choose between 3 levels (High, Normal, Low). After completing setting, click Apply button.
6. Alarm Notification This notifies the registered users of an alarm arising situation through e-mails. At this time, a maximum of 5 stored JPEG pictures, which were stored, can be sent together. - Menu Configuration Service SMTP server address Authentication Login User ID Password Sender (E-mail) E-mail address 1 ~4 Image count Choose enable if you want to send the ALARM notifying E-MAIL. SMTP server of the ISP that provides SMO-211QN/SMO-150QN with services. ISP’s confirmation required.
EX) When user who has an e-mail address (SMO-211QN@yahoo.com) and password(123456) in YAHOO, sets “Alarm Notification” in order to send a mail to (test1@yahoo.com). After completing setting, click Apply button. image transfer in your e-mail account. In the event of Alarm, please use PLAYER to catch normal JPEG images. Otherwise, the image size will be reduced to a half JPEG size. Refer to Eng-57 “How to play” for the detailed usage of PLAYER .
3-8-3) Network Configuration Menu. 1. Network Configuration On this menu, you can fix the general environment related to the network of the SMO-211QN/SMO-150QN Server and check the present status. - Menu Configuration Network Configuration PPPoE(DSL) Set “Static IP” or “DHCP”. Set PPPoE (DSL). Network Ports Set “Network Port”. View Network Status Modification of HTTP and other application network port numbers. Network Status Notify View network status.
1-1. Network Configuration : Static IP / DHCP Client 1) If the IP of the SMO-211QN/SMO-150QN Server is Static : Choose “Static IP”. 2) Type in the IP Address you want to assign to the SMO-211QN/SMO-150QN Server, NetMask, GateWay, DNS1, and DNS2 addresses. 1-2. Network Configuration : Static IP / DHCP Client 1) If the IP of the SMO-211QN/SMO-150QN Server is DHCP : Choose “DHCP Client”. 2) Type in the addresses of DNS 1 and DNS 2.
3) Click Apply button to apply the settings. If you click Reset button, the latest setting will be applied again. Click Back button if you don’t want to apply the setting. 4) If the mac address of an user is XX:XX:XX:FF:00:00, an user who uses DDNS but does not know the IP can connect the Viewer by typing as follows in the URL. EX) http://sff0000.websamsung.net If the mac address of an user is XX:XX:XX:FF:00:01, connect to SFF0001. EX) http://sff0001.websamsung.net * Note : MAC Address.
2. PPPoE (DSL) for Eth0 1) Service : Decide if you want to try PPPoE Connection or not. 2) User ID : User’s ID that is registered in the ISP. 3) User Password : User’s password that is registered in the ISP. 4) Confirm Password : Confirm the password. 5) DNS (Domain Name Service) : Service to convert a Domain Name (ex. www.yahoo.com) into an IP address (ex. 216.109.127.28). The SMO-211QN/SMO-150QN Server uses this service to join the FTP server or other webs by the Domain Name.
3. Network Ports Configuration It sets the HTTP Port number to use when the SMO-211QN/SMO-150QN Server communicates with a Client PC. The present SMO-211QN/SMO-150QN Server uses HTTP Port (80). - HTTP Port 1) This is the port the Client PC uses to connect to the web page of the SMO-211QN/SMO150QN Server. Depending on the environment of the network, its value may vary. 2) The fault values is 80 and can be assigned up to 65535 maximum.
4. View Network Status This is a menu to see the general status of the network setting of the SMO-211QN/SMO-150QN Server. - Menu Configuration Common Status LAN Status To check the status of the Gateway, DNS 1, and DNS 2. To check the status of the STATIC IP Address, Netmask, and MAC Address. PPPoE Status If the PPPoE service is connected, Link is up. At this time, the service IP and NETMASK can be also checked. If the PPPoE service is not in the connected, Link is down.
1) DHCP Client has been set in “Network Configuration” menu and an IP has been assigned from the actual DHCP Server to make communication possible. 2) PPP Client has been set in “PPPoE” menu and communication has become possible through the connection with ISP or PPP Server. - Menu Configuration Mail Notification E-mail forwarding or not. Enable : Forward E-mails. Disable : Doesn’t forward E-mails. SMTP Server Type in the address of the server that provides e-mail relay function.
Network Status Notify Configuration click “Network Status Notify” in the Network Configuration group. Choose to use the Mail Notification function or not. Choose “Enable” if you want to notify the network status of the SMO-211QN/SMO-150QN Server to people who through e-mails. Type the address of the SMTP Server. * SMTP Server plays a part as a relay that receives the mail of the user and delivers it to the receiver.
6. DDNS Configuration - Menu Configuration Server DDNS Server Select Enable or Disable Websamsung.net Note The domain name of this system is sff0000.websamsung.net CAUTION In case of a configuration using DHCP, as the connection to SMO-211QN/SMO-150QN is made using domain names (EX : http://sff0000.websamsung.net) that are automatically registered in Samsung's DDNS server, IP address, Subnet Mask and Gateway that are in the network tab of Admin Mode are not necessarily to be inputted.
3-8-4) Monitor Set up - Menu Configuration Please refer to CHAPTER3 of the user’s manual. Date & Time View Event Log Set the display data format and current time. Display the time and data of camera event and type of event. Dwell Time Displays each picture for pre-set time and automatically Switches it to the next picture in SEQUENTIAL DISPLAY MODE. Display Allows users to select the color andset theborder ON/OFF in the QUAD DISPLAY Title Set the title of each camera as desired.
3-8-5) Utilities This menu is for the flash memory’s update, rebooting, restoring to the basics, and system upgrade. - Menu Configuration Save Configuration Save Configuration is required to save all new configuration in the system.
1. Save Configuration This menu is to save all of the present setting in the Flash Memory. If you changed any of the settings for the SMO-211QN/SMO-150QN, it is recommended that you save it in the Flash Memory in this menu.
2. Reboot This menu is for the rebooting of the system. It is better to reboot the system if you change the setting and update the flash. 1. Click “Reboot” in the utilities group. 2. Click “Reboot!!!”.
4. System Update This menu is to update the inner programs and data of the SMO-211QN/SMO-150QN Server. They are recorded in the Flash Memory and composed of 4 parts called Kernel Image, Ram disk Image, System Image, and Web Image respectively. Each image file should be stored in the user’s PC for update. Depending on the range you want to update, press the start button properly. Normal (System and Web) Update Update only the System Web.
3-2. All (kernel, RAM disk, System, Web) Update When you click the start button located, a window will appear to ask if you want to update. Click “Cancel” to stop updating. 1. “OK” to proceed updating. 2. A pop-up window will appear. Choose “Zimage-ve” in the browser.
3. Click “Next” button to move to the next stage. Click “Skip” button to move to the next stage without Kernel Image’s update. Click “Next” button and a window will appear to check the name and size of the file.
Click Previous button to go back to the previous stage. Click the Next button to execute update of the program and move to the next stage. Click the Cancel button to stop the update process. 4. In the next stage, a pop-up window will appear for the file searching for the RAM Disk Update. Choose “rfs-ve.gz” in the browser.
5. Click “Next” button to move to the next stage. Click “Skip” button to move to the next stage without Kernel Image’s update. Click “Next” button and a window will appear to check the name and size of the file. Click “Previous” button to go back to the previous stage. Click the Next button to execute update of the program and move to the next stage. Click the Cancel button to stop the update process.
6. In the next stage, a pop-up window will appear for the file searching process for the System Image Update. Choose “fw_2pq-ve.tar.gz” in the browser. 7. Click “Next” button to move to the next stage.
Click “Skip” button to move to the next stage without kernel Image’s update. Click “Next” button and a window will appear to check the name and size of the file. Click “Previous” button to go back to the previous stage. Click the Next button to execute update of the program and move to the next stage. Click the Cancel button to stop the update process. 8. In the next stage, a pop-up window will appear for the file searching process for the System Image Update. Choose “web-ve.tar.gz” in the browse.
9. Click “Next” button to move to the next stage. Click “Skip button to move to the next stage without Kernel Image’s update. Click “Next” button and a window will appear to check the name and size of the file. Click “Previous” button to go back to the previous stage. Click the Next button to execute update of the program and move to the next stage. Click the Cancel button to stop the update process.
10. A window will appear for rebooting after completing all the update processes. Click the reboot button and press the confirmation button to reboot the system. 11. Close your web browser and wait for about a minute before you log in again Files related to the update of SMO-211QN/SMO-150QN Kernel Image RAM Disk Image zimage-ve rfs-ve.gz System Image fw_2pq-ve.tar.gz Web page Image web-ve.tar.gz The window shown above may not appear if there is a pop-up blocker installed in the user’s PC.
3-9) VIEW EVENT LOG MENU function and setting method • Function: Displays the time and date of camera event and type of event. • √ Setting method:Move to #7. VIEW EVENT LOG MENU by using œENTER√ SWITCH at SETUP MENU, then press the ENTER SWITCH to display the OSD as shown in the figure below. (The figure shows the initial setting status.) 06/01/03 Sequence of event happening Camera No. that event happened.
Chapter 4: DISPLAY MODE setting method 4-1) SINGLE SCREEN DISPLAY Initial display mode of monitor is QUAD - A. If you want to see the camera image at full mode, select a target camera by using ▲/▼ KEY. After that, press the ENTER SWITCH and selected camera image will be displayed at full screen. If you press the ▲/▼ KEY SINGLE DISPLAY MODE at this time, they can see another camera image at full screen.
4-2) QUAD MODE DISPLAY Users can switch SINGLE DISPLAY MODE and SEQUENTIAL DISPLAY MODE to QUAD DISPLAY MODE, or QUAD - A (QUAD - B) to QUAD - B (QUAD - A), or PIP MODE to QUAD MODE, press the QUAD/PAGE KEY.
4-3) AUTO SEQUENTIAL DISPLAY MODE Pressing on the SEQUENCE KEY on the front allows screen to automatically switch to SINGLE MODE full screen or QUAD MODE. (‘no-signal’ channels will be skipped while single screen is auto-switching.) If the DWELL TIME SETTING of SETUP MENU is set to 3 seconds and the SEQUENCE KEY is pressed at this time, the operation will be carried out as follows.
4-4) PIP MODE DISPLAY Can be used to see PIP screen in Single screen mode. If you press the SEQUENCE on PIP screen ,the Sub- screen will change. If you press the ▲/▼ KEY,the main screen can be transferred to another channel. Sub-screen location can be selected in DISPLAY MENU in SETUP MENU.
4-5) ZOOM MODE DISPLAY When users want to see a zoomed image of a specific area of the display, press the ZOOM KEY in the front to display zoom selection area. Select zoom target area by using ▲/▼ KEY, and press the ENTER SWITCH, then, the selected area will be displayed at full single mode with zoomed area doubled.In the zoom function operation in SINGLE DISPLAY MODE (CH2), the operation will be carried out as shown in figure below.
Chapter 5: Product features SOC-C120 : Standard Camera Model Name SOC-C120 Broadcasting System NTSC STANDARD Imaging Device 1/4 ”SUPER HAD IT CCD Effective Pixels S 510(H) x 492(V) Synchronization Internal Resolution H :330 TV Lines, V: 350 TV Lines Signal Output VBS 1.0Vp-p(75ohms composite) S/N Ratio ≤ 48 dB Minimum Scene Illumination 2lux(F2.0, 50 IRE) Gamma Correction 0.45 Lens Focal Length (f) : 3.8 mm, F Number = 2.
SOC-D120 : Dome Camera Model Name SOC-D120 Broadcasting System NTSC STANDARD Imaging Device 1/4 ”SUPER HAD IT CCD Effective Pixels 510(H) x 492(V) Synchronization Internal Resolution H :330 TV Lines, V: 350 TV Lines Signal Output VBS 1.0Vp-p(75ohms composite) S/N Ratio ≤ 48 dB Minimum Scene Illumination 2lux(F2.0, 50 IRE) Gamma Correction 0.45 Lens Focal Length (f) : 3.8 mm , F Number = 2.
SOC-P120 : PIR Camera Model Name Broadcast System Imaging Device Effective Pixels Synchronization Resolution Signal Output S/N Ratio Minimum Scene Illumination Gamma Correction Lens Auto Exposure PIR Sensor Audio I/O Connectors Operating Temperature Power Source Power Consumption Dimensions Weight SOC-P120 NTSC Standard 1/4" Color IT CCD 510(H) X 492(V) Internal H :330 TV Lines, V: 350 TV Lines VBS 1.0 Vp-p (75 ohms composite) ≤ 48dB 2 lux (F2.0, 50IRE) 0.45 Focal Length :3.8 mm, F Number = 2.
OBSERVATION MONITOR Video Input • CAMERA 8 Input: 1.0Vp-p(CVBS), 75Ω (vertical) • VCR 1 Input (to Video Out of VCR) : 1.0Vp-p, 75Ω (vertical) Video Output • VCR 1 Output: 1.
NETWORK Hardware • 32bit Embedded Processor • Flash Memory : 8Mbytes • SDRAM : 32Mbytes Network Protocols • HTTP, TCP/IP, FTP, Telnet, ARP, PPP, DHCP, PPPoE Image Compression & Quality • Compression Algorithm : Real-time fmpi • Rate : 30 fps for each channel • Quality : 3 levels Video Format • NTSC Video Resolution • NTSC, 352x240, 704x240 Performance • Max 30 Frame Per Second (NTSC) Management • Configuration by serial port or web browser • Remote Flash memory update LAN Interface • 10/100 B
The system performance may decrease if the computer has lower specification than the recommendations, is not installed with the latest service pack, or has an illegally installed operation system(OS). A unique MAC address is registered to this device. If the administrator setting and monitoring may not be available due to conflicting unregistered MAC addresses, please contact a local service center or head office. SMO-211QN/SMO-150QN enables users to see up to four viewers on one computer.
Appendix A) Software up data The initial screen of Samsung Electronics’ web site is as follows. 1. http://www.securitysamsung.com http://www.samsung.com/Products/CCTV.htm 2. Network Security in Homepage 3. Download the following items for SMO-211QN/SMO-150QN.
Appendix B) IP Router Setup Guide List of Routers compatible with SMO-211QN/SMO-150QN. Refer to Router User’s Manual for the detailed router setup. Step-by-Step Examples : Linksys (Model : WRT54G) Netgear (Model : WGR614v4) D-Link (Model : DI-624+) SMC (Model : 7004VBR) CAUTION Other routers may be incompatible with SMO-211QN/SMO-150QN.
Step-by-Step Setup Example of IP Router Linksys model WRT54G 1. Click the “Application and Gaming” tab. 2. Click “Port Range Forward”. 3. Port forwarding Row #1 : ! Application : Set this to “HTTP” @ Start and End : Set both to “From 10000 to 65535” # Protocol : Select “TCP” $ IP Address : SETUP MENU -> 7. NETWORK SETUP -> Check IP from network status to apply it identically to Private IP after DHCP setup.
Step-by-Step Setup Example of IP Router Netgear model WGR614v4 SMO-211QN/SMO-150QN 10000 10000 192.168.0.101 1. Click the “Router Status” 2. Click the WAN and LAN Port information. Write down the WAN Port IP Subnet Mask number and the LAN Port IP Address number. You will need it later when setting up the SMO-211QN/SMO-150QN. 3. Click “Advanced” and “Port Forwarding” 4.
Step-by-Step Setup Example of IP Router D-Link model DI-624+ 1. Select “Virtual Server” and “Advanced” You need to create Virtual Servers (Port Forwarding) for HTTP, TCP and Upgrade separately. 2. Virtual Server (Port Forwarding) for HTTP ! Enabled : Leave this “checked” @ Name : Set this to “HTTP” # Private IP : SETUP MENU -> 7. NETWORK SETUP -> Check IP from network status to apply it identically to Private IP after DHCP setup.
Step-by-Step Setup Example of IP Router SMC model 7004VBR 1. Select “NAT” and “Virtual Server” You need to create Virtual Servers (Port Forwarding) for HTTP 2. Virtual Server (Port Forwarding) for HTTP : use the first empty ID row. ! IP Address : SETUP MENU -> 7. NETWORK SETUP -> Check IP from network status to apply it identically to Private IP after DHCP setup. (Eng- 41 Setup) * That is not in use by any other device connected to the Router including the Local PC.
HEADQUARTERS 105 Challenger Road Ridgefield Park, NJ 07660-0511 TEL:1-800-SAMSUNG SERVICE DIVISION 400 Valley Road,Suite 201 Mount Arlington, NJ 07856 1-800-SAMSUNG(1-800-726-7864) www.samsung.com Part No.
