Samsung SmartCam User Manual SNH-1010N
SPECIFY SERVICE INSTRUCTIONS AND WARRANTY TERMS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
• Never use the product near bath tub, sink, washing machine and in wet basement to avoid moisture. • The product is designed for indoor use. • The product is not designed for medical monitoring, and requires a grown-up’s protective supervision on its use. • To avoid overheating of the product, do not expose the product to direct sunlight; do not install or use near a heat source such as heater, radiator, cooking devices (ex: electric stove or oven) and other warming devices (ex: audio amplifier, TV, etc.).
01 Getting Started Key Features Product and Accessories 4 5 Basic Information 6 Product At a Glance 6 Key Features • Easy to install - With the help of WPS (WiFi Protected Setup), wireless sharing and easy connection are enabled. - Simply visit the home page (www.samsungsmartcam.com) and download and install the program without a separate installer program. • Remote monitoring - Whenever and wherever if you are in the Internet enabled environment, remote monitoring is ready for you.
Product and Accessories Check for above components when opening the product package. 01 Power Adaptor Quick Start Guide License Information Warranty Card Bracket Double-sided Tape Network Cable Getting Started n` Camera Please save the packaging. you will need the serial number later to register the camera.
Basic Information Product At a Glance Front View High quality camera lens Built-in IR LEDs for night vision Power status LED WiFi status LED Flashing White: Searching for wireless network Steady White: Wireless network connected Off: Connected via network cable Bottom View Holes for wall mount bracket Built-in speaker · English Red: Power On, Boot-up in process White: Camera ready Yellow: Privacy mode enabled Magenta: Updating firmware Built-in Mic
Side View 01 Getting Started WPS Button Used to connect to the Wireless Access Point Press and hold for 3sec to initiate WPS mode Privacy Button Rear View Press for 3sec to stop transmitting video/audio Press and hold for 10sec to reset the camera to default settings DC 5V Power Input Network port Used if WPS is not supported on the Wireless Access Point or if you do not have a Wireless Access Point
02 Installation & Network Connection Installation Precautions Desktop mounting Wall mounting Power Supply Network Connection and Settings Precautions Connecting via network cable Connecting via WiFi without WPS feature Conneting using WiFi WPS feature · English 8 8 9 9 10 11 11 11 12 12 Installation Precautions 1. Install the camera in a place where the WiFi signal can be reached and without interference. 2. Keep it away from humidity such as around the humidifier. 3.
Desktop mounting 1. Place the camera in a desired position on the surface. Wall mounting 1. Use a double-sided tape to secure the bracket to a desired position. n` You can use the screws to tighten the camera. (not included) 02 ` The double-sided tape cannot be reused after being used once. 2. Adjust the camera’s shooting angle as appropriate. Do not put excessive force. Otherwise, it may cause damage to the camera.
3. Adjust the camera’s shooting angle as appropriate (left and right) and tighten the screws on the bottom of the bracket. n` You can also use a coin or flat-head screwdriver to tighten them. 5. Plug in the power cable and arrange the cables through the bracket holes. n` When done, remove the protective film from the lens. Power Supply 4. Adjust the camera’s shooting angle (top and bottom). n` Plug-in the camera power adapter to the wall outlet and connect the camera as shown.
Network Connection and Settings Precautions • The wireless network access may fail, depending on the communications environment. • For details about the network settings and password, contact your network administrator or service provider. • Do not access the unauthorized network. If you do not have a Wireless Access Point, you must connect the camera using LAN cable directly to your home router. 1. Connect the network cable to the camera and to the home router as shown below.
Connecting via WiFi without WPS feature Conneting using WiFi WPS feature If you want to connect the camera using a non-WPS Wireless Access Point, change the network setting to Wire and try the wireless network. What is WPS? WPS enables to make connection between the camera and the Wireless Access Point with a simple click of the button. 1. Use the network cable (LAN cable) to connect the LAN port of the unit to the LAN port of the Wireless Access Point. 1.
Monitoring Registration Web browser requirements Starting SmartCam Live Video Monitoring options Set up Basic Info Network Time Alarm & Notification Alarm Schedule 13 13 13 18 19 20 20 21 23 23 26 Event Alarm 27 Information 28 My Account Support 28 29 Once you register the product with the site, you can monitor the camera video on the PC or laptop computer. Web browser requirements Windows - Windows XP ,7 supported - Internet Explorer 8, 9 (The 64-bit is not supported.
Plug in installation You need to install your plug in to automatically search for cameras connected to the network and view the video in your camera. n` 3) Click to begin the installation. 4) Installation has completed. If you login or click in a PC where the plug in is not installed, the installation message window will pop up. ` When you install the plug in, the web browser will be terminated and you need to launch it again.
For Mac 2) Click . 4) Enter password, and click . 03 Click . 5) Monitoring 3) Installation has completed.
5. Provide the requested information, and click . • ID: Create the user ID and click the . Fill in the user ID in 8 ~ 14 alphanumeric characters and ‘.’. • Password: Create a password between 8 to 14 characters using both letters and numbers. • Confirm Password: Please enter the password again for confirmation. • Name: Enter the user name. • E-mail: Enter the correct email address as it is used for reference in case you forgot the user ID or password.
9. Create and . 10. Click . 12. Select your Wireless Network from the list. 13. Enter the password of your Wireless Network and click . 03 Display Strings The camera password is used to block the unauthorized access to your camera. Create camera password using alphanumeric characters between 1 to 8 without any space. 11. After adding the camera, click in the wireless network setup pop-up window.
15. Unplug the network cable from the camera and the router. 16. Click if the button is activated. Live Video 1. Select a camera from the camera list at the upper left hand of the screen. 17. Once the camera is successfully registered, you can check the camera in the camera list. n` 2. The gray icon indicates the camera is inactive so you cannot monitor it right now. Enter the camera password and click .
Monitoring options 1 2 Item 3 10 6 7 8 9 Item Full screen 5 Night Vision 6 Flip You can flip over the video image. 7 Capture Image Saves a picture of current live image you are viewing. 8 Network Speed Select frame rate based on your network speed. If the bandwidth provided by the cable service provider is lower than recommended, you may encounter a blurry image or a temporary loss of video signal. 9 Sound When enabled, you can hear what’s happening around the camera.
Network Speed Profile Name Recommended bandwidth Resolution Frame rate Low Speed Network VGA 5 fps 768Kbps Mid Speed Network VGA 10 fps 1Mbps High Speed Network VGA 20 fps 1.5Mbps n` ` ` ` ` ` 20 · English What is Relay Mode? Depending on your network connection, peer to peer connection may not be available. If you cannot make a peer to peer connection, the camera should be connected in relay mode.
n Network ` If you change the camera password, you will be logged out and return to the camera password input page. ` Keep the camera password in a safe place as it is used for viewing the live screen of the camera or for changing the display settings. Firmware update If the currently used S/W is not of the latest version, update it. If you are using the latest version, then the firmware will not be activated. 1) Click . 1 03 2 Click the < > icon to update the firmware.
n`` If any of the manual settings is wrong, the network settings will not be applied. If you have both cable and wireless network connections simultaneously, the cable network connection is prioritized. ` Press WPS to set the network connection to Wireless regardless of the current network settings. When the system reboots, it will switch to Cable if the cable network connection is already established.
Time Alarm & Notification Camera has ability to send event notifications when motion or audio is detected. 1 2 3 4 5 Item Item Description Confirm the camera’s time. 2 Time Zone Select your region. 3 Display Time Select time format on display. 4 Automatic Time It will display the current time to which the summer time is not applied. 5 Daylight Saving Time Check this option if you live in a country or region where DST(Daylight Saving Time) is applied.
Notification setting After clicking , select your email address and password. The setting is required if you want to use YouTube/Picasa/Gmail. Automatically uploads a image to your private Picasa account. Notification Automatically uploads 30 second clip to your private YouTube account. 1. Select the Google. 2. Check
Notification Notification The event alarm is sent through Gmail. When an event is detected, the notification message is sent to the user’s Twitter account. 1. Select the Google. 1. Select the Google. 2. Check
Push alarm Notification Alarm Schedule The push alarm is provided through the web viewer and mobile app in which the camera is registered. Set the desired time to activate alarms for the selected time period. 1 2 - If this is set to Enabled, the video and image link recorded in YouTube and Picasa will be transferred to the listed friends in real time in the event of an alarm. - The video/image alarm will be transferred only if you have set the Youtube and Picasa enabled.
Event Alarm You can check the event alarm. 3 4 03 1 5 2 Description 1 Delete by dates Delete all the event alarms on the date. 2 Play Video Select an event and double click on it. The video will be played. Video can be played only if you are logged into the Google account where you uploaded the video. 3 Delete All Delete all the event alarms for thirty days. 4 Display Events Displays the number of events occurred in the 30 day list.
Information My Account n` 28 · English If you want to change your information, click < > icon and move to “Account” page and select an item (password and/or email address) and make changes as necessary.
Support You can download the Samsung SmartCam mobile app and user guide. 03 Monitoring n` lf you want to know more information of camera, move to “Support” page.
Appendix 04 Specifications 30 · English 30 Specifications Product Appearance 30 32 Troubleshooting 33 Specifications Specifications Sensor Item Imaging Device SNH-1010N VGA 1/6 inch CMOS Lens Focal Length (Zoom Ratio) 2.17mm Angular Field of View (D/V/H) 64.5°/ 41.0°/ 50.
Item Item SNH-1010N Network Mobile application support SNH-1010N iPhone 4/5, Galaxy S2/S3 (Recommended Smartphone) iPad 2/3, Galaxy Note 10.1 (Recommended Tablet PC) Ethernet RJ-45 (10/100BASE-T) Wireless WiFi 802.11 b/g/n WPS (WiFi Protected Setup) Support WPS Button Operating Temperature / Humidity Video Compression Format H.264, MJPEG Electrical Resolution 640x480, 320x240 Input Voltage / Current 5V DC / 2.2A Max. Framerate 20fps (640x480) Power Consumption Max.
Product Appearance 32 · English
Troubleshooting Problem If you encounter a problem with your system, see the table below to solve the problem as quickly and easily as possible. Please follow the instruction below: Problem I forgot my user ID/password. Action ove to “Log-in page -> Forgot your ID/Password?”, and enter - M the registered e-mail address to which we will send you the user ID and/or a new password. It can be spammed out depending on the policy of the email server.
Problem The video from the camera is temporarily lost. No sound is output from the video. I forgot my Camera password. Action he video from the camera will be affected by the illumination of - T the installation site of the camera. This is why the video from the camera looks lost if the camera is installed in a low illumination environment. he video from the camera can be delayed according to a - T network delay.
Samsung Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products. The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive.
SALES NETWORK • S AMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL: +82-70-7147-8740~60, FAX: +82-31-8018-3745 • SAMSUNG TECHWIN AMERICA Inc. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free : 1-877-349-3149 www.samsungsv.com • SAMSUNG TECHWIN EUROPE LTD.
