SHR-1040/SHR-1040K-ENG 2006.4.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` ii SHR-1040/1040K USER’S MANUAL Safety Regulations Please be sure to keep the following in mind for the right use of the product to pre-vent proprietary risk or damage. ■ Do not use multiple plugs at once. ● ■ Do not put a vase, flowerpot, cup, cosmetics, medicine, or vessel with water around you. ● ■ This may cause fire. Do not disassemble, repair, or remodel the product. ● ■ This may cause abnormal operation due to high temperature.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` iii Before we start This User’s Manual describes the basic usage of SHR-1040. This Manual contains all the matters necessary for using SHR-1040 such as brief instruction, part name, function, connecting other equipment, and menu setup of SHR-1040. - SEC retains the copyright on this User’s Manual. - This User’s Manual cannot be copied without SEC’s prior written approval.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` iv Contents ii Safety Regulations iii Before we start Standards Approvals 1 1-1 1. Introduction 1-2 2. Features 1-3 3. Part Names and Functions 1-6 4. Remote Controller 2 Chapter 2. Installation 2-1 1. Installation Environment Setup 2-2 2. Checking Product & Accessory 2-3 3. HDD Addtion 3 English Chapter 3. DIY Carmera 3-1 1. Standard Camera 3-5 2. Nightvision Camera 4 Chapter 4. Connecting with Other device 4-1 1.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` v 6 Chapter 6. Menu Setup 6-1 1. Main Setup Menu 6-2 2. Clock/Display Setup 6-3 3. Record Mode Setup 6-4 4. Title Setup 6-5 5. Dwell Time Setup 6-6 6. Alarm Setup 6-7 7. Event Record Mode Setup 6-9 8. Timer Record Setup 6-10 9. System Setup 6-14 10. System Information 7 Chapter 7. Recording 7-1 1. Basic Recording 7-1 2. Timer Recording 7-2 3. Motion Recording 7-2 4. Alarm Recording 7-3 5. Stop Recording 8 Chapter 8.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 1 Chapter 1.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 1-1 SHR-1040/1040K USER’S MANUAL 1 Introduction The SHR-1040 digital video recorder is a digital video recorder that records and plays back video and audio input from four cameras. It records and plays back each channel of video data in MPEG4 format, and audio data in installed HDD format, by using the G-723 compression standard.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 1-2 2 Features Adjusts recorded data in three steps. - HIGH, NORMAL, LOW ■ Adjusts the number of record fields per second. - NTSC : 1~ MAX 30 IPS ■ Records before-event (Alarm or Motion) data based on pre-set hours. (Pre-Alarm) - 0 ~ 5SEC ■ Audio-records and plays back selected channels. ■ Offers a timer used for time record. ■ Records video and audio with alarm. ■ Offers various playback speeds. ■ Offers easy-to-use search functions.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 1-3 SHR-1040/1040K USER’S MANUAL 3 Part Names & Function [SHR-1040] No. Name 1 1 2 4 ... MODE 3 Function Power LED Displays power On/Off condition. Alarm LED lights on when an event occurs. HDD LED Displays Normal Access to HDD. Upon Access to HDD, LED repeats on and off. Rec LED Displays the record condition.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ No. ` 1-4 Name Function ZOOM ZOOM 7 FREEZE FREEZE 8 SEQUENCE You can view X2 screen by pressing the ZOOM Button in the single screen. When you press the up/down and the left/right key in the Zoom screen, the selected Zoom Area moves. Press the Enter button to view X2 Zoom Screen of the selected area. Press the Freeze Button to freeze the current displayed screen, and press the Freeze Button again to cancel the Freeze.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 1-5 SHR-1040/1040K USER’S MANUAL [SHR-1040] Caution The ventilation outlet may be blocked. Do not operate the DVR on a carpet or other soft surfaces. When you operate the DVR in a cabinet or on a rack, check whether a ventilation device is properly installed. No. 1-5 English Name Function 1 CAM IN RJ-11 Connector linked to the Port DIY CAMERA.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 1-6 4 Remote Controller 1. RECORD Starts the recording as the setup record setting in normal record mode. 2. ID RESET 15. SYSTEM ID Confirms system and remote control ID and changes the remote control ID. 16. PIP In Single mode, press to watch another channel in a sub picture. The ID is reset. 3. NUMBER KEY Press to select one of single channels in Live mode. Use this for typing purposes in a numeric input mode. 4. MODE Selects split-screen. 5.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 1-8 Chapter 2.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-1 SHR-1040/1040K USER’S MANUAL 1 Installation Environment Setup Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator. To play DVR on the cabinet or rack, be sure to check the ventilation condition. You should pay attention to the following before you use the product. 1. Do not use it outdoor. 2. Do not let water or liquid in the connection part or the product itself. 3. Do not impose excessive shock or force. 4.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-2 2 Checking Product & Accessory Upon delivery of a product, you shall unwrap the product and put it on the even floor or where you want to use it. Then you shall check if the following items are in it.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-3 SHR-1040/1040K USER’S MANUAL 3 HDD Addtion You can install one additional hard disk drive inside the product (Max. 2 HDDs). However, there are lots of factors inside that may cause electrical shock, physical damage or malfunction. So please follow the instructions below to mount the HDD as the product couldn’ t recognize the additionally installed HDD or may not work properly due to incorrect installation or connection.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-4 5. Disconnect the power supply cable and the signal cable (IDE cable) from the current HDD. Push the bracket to the arrow direction as in the picture below and lift it up from the bottom. 6. Use the four screws provided (SCREW-SPECIAL: PWH,+,-,6-32UNC,L14.7(4.2),ZPC) to fix the old HDD and the additional with the bracket (Make sure you fasten the screws firmly so that they are not loose from vibration).
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-5 SHR-1040/1040K USER’S MANUAL 7. Mount the HDD-fixed bracket to its original position. (Installation is done in the reverse order of the disassembly. Fit the bracket (BRACKET-HDD) into the bottom hole and fix the screw). 8. When done (make sure the bracket is firmly fixed), connect the power supply cable and the signal cable (IDE) to both the old and the additional HDD (see the picture below). 9.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-6 10. Use the screws (two for each side and one for the rear) in step 1 above to fix the cover.
SHR-1040/SHR-1040K-ENG 2006.4.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-8 Chapter 3.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-9 SHR-1040/1040K USER’S MANUAL 1 Standard Camera Composition and Installation Method 1) STANDARD CAMERA COMPOSITION (SOC-C120) a. Lens It has a focal length of 3.8mm and makes it possible for you to observe a relatively wide area. b. Microphone Capable of picking up all sound in the vicinity of the camera location and transmitting to the monitor. c. Camera fitting groove Enables the camera to be fixed onto the bracket.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-10 2) INSTALLING STANDARD CAMERA (SOC-C120) SOC-C120 camera can be attached to the wall, ceiling or shelf using the camera mount bracket (SBR-110S). Choose an installation site that can sufficiently support the weight of the equipment to be installed. Attach the camera mount bracket to the wall or ceiling using the supplied three screws (M4 X L15). Adjust the camera to target the video location and tighten the bracket handle on the camera mount bracket.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-11 SHR-1040/1040K USER’S MANUAL • Adjust the camera to target the video location and tighten the bracket handle on the camera mount bracket. Install the camera on to the male screw of the Camera Mount Bracket by rotating the camera in clockwise. • Loosen the handle by turning it in a counter-clockwise direction and then adjust the camera position . Tighten the handle, turning it clockwise, and lock the camera in position.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-12 After positioning the monitor and installing four cameras in the desired location, please connect the CAMERA to the DVR using the CAMERA CABLE (MCB-60) as shown in the figure below. Connection status checking method : • Turn on the DVR after connecting cameras, and check if camera image is displayed. • If the DVR and the camera are not connected properly, OSD ‘L’(LOSS) will be displayed on screen.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-13 SHR-1040/1040K USER’S MANUAL 2 Nightvision Camera 1) Before Installation SOC-N120 INTRODUCTION SOC-N120 Nightvision camera is intended to be used exclusively with those sold by this company for DIY. With the built-in IR LED and light sensor in the camera, both day monitoring and night monitoring are possible. Also, since it is designed as water-proof daily product, it can be used not only indoors, but also outdoors.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-14 3) Installation 1. Make sure the installation location is a place where 5 times (about 2.2lbs) of the total weight of the camera can be tolerated before installing the camera. 2. Connect the cable below the camera after attaching the provided Mount Bracket to the desired place. 3. Use the handle on the Mount Bracket to adjust the direction you want to setup for monitoring.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 2-15 SHR-1040/1040K USER’S MANUAL 4) Title of Each Component a). Lens - It has a focal length of 3.8mm and makes it possiblefor you to observe a relatively wide area. b). Illumination Sensor - Detects incoming light to control the IR LED. c). IR LED - This is an infrared LED that is controlled by the illumination sensor. d). Camera fitting groove - Enables the camera to be fixed onto the bracket.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 3 Chapter 4.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 3-1 SHR-1040/1040K USER’S MANUAL 1 Connecting the Video, Audio, and Monitor [SHR-1040] Caution - Do not connect the Video In (BNC Input) and the RJ-11 (DIY Camera) input with the same channel at the same time. If connecting them simultaneously, two input signals may be mixed when outputting. This is not the product defect; so, please connect only one between the two inputs. - When the first delivery, the Video output is set to the CVBS (BNC Output) output.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 3-2 2 Connecting the Alarm Input/Output The Alarm IN/OUT port in the back of SHR-1040 is composed of the following elements. ALM OUT G ALM RST ● ALM IN ALARM IN/OUT Connection Name Function 1 ALM IN ALARM Input Port 2 ALM OUT ALARM Output Port 3 ALM RST On receiving an ALARM RESET signal, the system cancels the current ALARM input and output signal and then resumes sensing.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5 Chapter 5.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 4-1 SHR-1040/1040K USER’S MANUAL 1 System Operation Turning Power On ● When the adapter is connected to the DC 12V connector on the back panel, the Power LED on the front is lit. The following screen appears, and the system is booted. Detection of Video In Signals ● 5-1 English If no video signals exist when the system is turned on, the letter L (for Loss) lappears next to the title (CAM1…CAM2) of the screen, and the screen turns black.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 4-2 2 Live Screen Mode Full Display Screen Markers and displays on the screen are seen as below. Play 05/05/01 00:00:01 01/01/06 12:00:00 AML CAM 1 S AML CAM 2 AML CAM 3 AML CAM 4 For Live, it indicates the current time and date as set in the system. For playback, it indicates the time and date of the data recording. marker is displayed when the system in recording mode. Prevents the cancellation of REC.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 4-3 SHR-1040/1040K USER’S MANUAL 3 Key Functions 1. CHANNEL KEY & MODE KEY ● ● ● ● ● Use the CHANNEL Key when you want to view the channel in full screen. Press the desired channel key to view the channel in full screen. Audio of the channel is also selected. The S mark appears next to the title of the selected channel, and the audio of the channel is off. Audio recording is available for the one selected channel.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 4-4 3. ZOOM KEY ● ● ● ● ● The ZOOM Key is used to X2 zoom the selected area in 1CH mode. Press the ZOOM Key to display the ZOOM area (default: Center Area). Press the ZOOM Key repeatedly to display or clear the ZOOM area. Press the ZOOM Key to zoom the selected area, and press the ENTER key to clear the ZOOM and display the marked area. ZOOM function is operated in the Single screen mode. SINGLE. 4.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 4-5 SHR-1040/1040K USER’S MANUAL 5. SEQUENCE KEY ● The Sequence Key is used for automatic channel sequencing. It is enabled only in Live Mode. Channels are switched in sequence and the Loss channel without video signals are skipped during the Dwell Time set by the Setup Menu. (Switch from 1channel ➝ 2 channel) ☛ Sequence in the Full Screen CH1 ➝ CH2 ➝ CH3 ➝ CH4 ➝ CH1 ➝ CH2 ➝ CH3 ➝ CH4 ➝ ......
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5 Chapter 6.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-1 SHR-1040/1040K USER’S MANUAL 1 Main Setup Menu 1. CLOCK/DISPLAY - Set the time, date and display items. 2. RECORD MODE - Set record-related items. 3. TITLE SETUP - Set channel titles. 4. DWELL TIME SETUP - Set the dwell time for each channel for sequence operations. 5. ALARM SETUP - Set the alarm channels and setup/alarm-related items. 6. EVENT RECORD MODE - Set the recording and motion detection items when the alarm is on. 7.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-2 2 Clock/Display Setup ● Set the time, date and display items. (1) DATE TYPE - Date can be displayed in three types, and the user can choose one among the three. [YY/MM/DD, MM/DD/YY, DD/MM/YY] (2) DATE - Set the present data. (3) TIME [HH:MM:SS] - Set the present time. (4) DATE/TIME - Set the date/time to ‘‘On’’ to display it on the screen, set the date/time to ‘Off’ to not display it.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-3 SHR-1040/1040K USER’S MANUAL 3 Record Mode Setup (1) PICTURE QUALITY - Define the picture quality in three steps when recording. High means top quality, followed by Normal and Low. [NORMAL/HIGH/LOW] (2) PICTURE RATE - Set the number of record fields for video In. [1/2.5/3.75/7.5/15/30] (3) DISK END MODE - When the mode is set to Stop, recording is stopped if the HDD becomes full during recording.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-4 4 Title Setup ● The default settings of the title setup menu are shown as follows. (1) TITLE SETUP - You can set the title of each channel as you want. - You can change the title by using …,†,œ,√, ➛ 0123456789 ABCDEFGHIJKLMNOPQRSTUVWXYZ :=.( ) [/]_+ - Place the cursor on the “ ” area when the title is not displayed. Press Enter to delete OSD.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-5 SHR-1040/1040K USER’S MANUAL 5 Dwell Time Setup ● The default settings of the Dwell Time are shown as follows. (1) DWELL TIME SETUP - Press the Sequence button in single screen to enter Sequence Mode. You can set the dwell time of each channel before switching. When the Dwell Time is set to 0 seconds, the channel is skipped and the next channel appears. [0SEC, 1SEC, 2SEC, 3SEC....................
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-6 6 Alarm Setup ● The default settings of the Alarm Setup Menu are shown as follows. (1) ALARM SETUP - Set the alarm setup to ‘ON’ to enable the alarm of each camera. Set the setup to ‘OFF’ to disenable alarm. [ON/OFF] (2) HOLD TIME - When Alarm occurs, set the hold time of alarm. [5SEC, 6SEC, 7SEC, 8SEC ~ 59SEC , 1MIN, 2MIN, 3MIN ~30MIN] (3) ALARM ON TIME - Set the start time of alarm operation.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-7 SHR-1040/1040K USER’S MANUAL 7 Event Record Mode Setup ● The default settings of the Alarm/Motion Recording Setup menu are shown as follows. (1) EVENT RECORD ENABLE Set the EVENT RECORD ENABLE to ‘On’ to start recording when alarm occurs, and set the EVENT RECORD ENABLE to ‘Off’ to not start recording when alarm occurs. If you exit the menu after setting the EVENT RECORD ENABLE to ‘On’, the system records data whenever an alarm occurs.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-8 (4) MOTION DETECTION - When the Motion Detection is set to ‘ON’, the system records input video whenever a motion is detected. [ON/OFF] (5) SENSITIVITY - You can set the level of sensitivity of motion detection when setting motion detection. HIGH/NORMAL/LOW. High indicates the highest level of sensitivity of motion detection, and Low indicates the lowest level of sensitivity of motion detection.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-9 SHR-1040/1040K USER’S MANUAL - Motion is detected only from channels set to ‘On.’ The following screen shows motion recording after motion detection. A motion is deteced in the Channel 1. The ‘M’ mark before the title of each channel indicates that a motion is detected. [ON/OFF] 8 Timer Record Setup (1) TIMER: Set the Timer to ‘On’ to enable timer recording. [ON/OFF] (2) DAY: Set the day of the week to record data.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-10 9 System Setup (1) PASSWORD - The default password : 4321 - You can set the password to limit access to the Main Screen setup by unauthorized people. (Create a four-digit password by choosing between 1~4.) You can enter the password from No. 1 to No. 4 using the corresponding channel key. Once the password is entered, you’ll see the following message that asks if you want to change the password.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-11 SHR-1040/1040K USER’S MANUAL (3) RECORD LOCK If you set RECORD LOCK to ON and press STOP to release the current recording, you are prompted to enter the PASSWORD. (4) HDD ERASE If you exit the Menu after setting HDD ERASE to ON, you will see the following message that asks if you want to erase the data on the HDD. If you click OK, you’ll see “HDD ERASE” as in the next picture, and the existing HDD Data is erased.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-12 (6) SYSTEM ID Set the System ID to use the Remote Controller. When using more than one unit of the system, a number of systems may be operated at the same time with a single remote controller. Set the different IDs for different units. Press the System ID of the Remote Controller and use the number keys to create IDs. After the setting, systems with IDs that correspond to the ID of the remote controller will operate.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-13 SHR-1040/1040K USER’S MANUAL Once the system switched to 1 channel mode, all system functions operate in 1 Channel mode and the items of other channels in the MENU are deactivated. Once the system switched to 1 channel mode, you can just play the data in this mode and the data recorded in 4 Channel mode could not be played.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 5-14 10 System Information (1) HDD NO Displays HDD quantity that is installed on the system. (2) CAPACITY Displays the HDD capacity of the System. [Remaining Capacity/Entire HDD Capacity] (3) VERSION Displays the version of the System.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 7 Chapter 7.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 6-1 SHR-1040/1040K USER’S MANUAL 1 Basic Recording Press the Record button ( ● ) to record live video. The Rec LED is lit, and the ( ● ) mark appears on the screen. The HDD LED blinks, indicating that data is being recorded to the HDD. Note You cannot record previously recorded data now being played back. To record the data, you must stop the playback of the data first. 2 Timer Recording - You can set the time and date of recording.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ 3 ` 6-2 Motion Recording Start recording when a motion is detected in the channel and area set by the Alarm/Motion Record Setup menu. When the motion record begins, the M mark is displayed next to the channel, indicating recording is on. Note - To enable the motion detection, you have to set an area for each channel. MOTION DETECTION operates only if there is a motion detected in the area of the channel you have selected.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 6-3 SHR-1040/1040K USER’S MANUAL 5 Stop Recording ● 7-3 English Click the Stop button to stop data recording. The REC mark disappears as follows, and recording is stopped. To stop data recording, click the STOP button. The REC mark disappears and the current recording stops as shown in the picture. However, if RECORD LOCK is set to ON, you have to enter the password to stop recording.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 7 Chapter 8.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 7-1 SHR-1040/1040K USER’S MANUAL 1 Search Menu ● Search Menu Press the Search button in Live mode to search recorded data. The following screen appears. Search is not enabled during recording. Stop recording to start search. - DATE & TIME SEARCH : Search recorded data based on the time and date. - RECORD EVENT SEARCH : Searches for all data recorded in Normal Record or Timer Record.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 7-2 2 Date Time Search (1) DATE[YY/MM/DD] Set the date (year/month/day) you want to search. (2) TIME[HH:MM:SS] Set the time you want to search. (3) SEARCH START Enter the year/month/day/hour/minute/second you want to search. Press the Enter button ( ) to search the time and date. 3 Record Event Search ● The following screen appears when selecting the Record Event Search after pressing the Search button.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 7-3 SHR-1040/1040K USER’S MANUAL 4 Alarm Event Search ● The following screen appears when selecting the Alarm Event Search after pressing the Search button. ● Displays the list of the data recorded in ALARM or MOTION RECORD out of all data on the HDD. Select from the Record Event List by using up/down left/right buttons (…,†,œ,√). Press the Search button after selecting from the Alarm Event List to start search.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ 6 ` 7-4 Power Event List ● Display the list of the time and date record of Power On/Off. ● You can view the list on the following page by using the up/down/left/right buttons (…,†,œ,√). Note Enter the Time Record Mode from the Menu screen, and set On/Off before setting the time and date of recording. You can also set the number of fields to be recorded per minute. 7 Basic Playback ● Press the Play/Still Button to play back the recorded data on the HDD.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 7-5 SHR-1040/1040K USER’S MANUAL Note Enter the Timer Record Mode from the Menu screen, and set On/Off before setting the time and date of recording. You can also set the number of fields to be recorded per minute. ● When the system reaches the end of the HDD during playback or the end of the current data, the system will start playing back from the beginning of the first data on the HDD.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 7-6 Chapter 9.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 8-1 SHR-1040/1040K USER’S MANUAL 1 Product Specification 1) SHR-1040, SHR-1040K Block Function SHR-1040 SHR-1040K(DIY Kit) NTSC 4 BNC, 4CH(RJ-11 DIY Camera) 2 BNC, 2RCA, 1VGA Video 1ch - FullScreen, Quad, Sequence, Display Mode Freeze, Zoom, PIP 720*480 Display Resolution 4CH(RCA), 4CH(RJ-11 DIY Camera) Audio Input Audio 2 CH(RCA) Audio Output 1CH mode : 30IPS Video REC/PB Speed 4CH mode : 120IPS MPEG4 Video CODEC G.
SHR-1040/SHR-1040K-ENG 2006.4.4 11:12 AM ˘ ` 8-2 2) SOC-C120 : Standard Camera Model Name Broadcasting System Imaging Device SOC-C120 NTSC STANDARD 1/4” SUPER HAD (Hole Accumulation Diode) IT CCD Effective Pixels S Synchronization Resolution 510(H) x 492(V) Internal H :330 TV Lines, V: 350 TV Lines Signal Output S/N Ratio Minimum Scene Illumination Gamma Correction Lens Auto Exposure VBS 1.
SHR-1040/SHR-1040K-ENG 2006.4.
SHR-1040/SHR-1040K-ENG 2006.4.
SHR-1040/SHR-1040K-ENG 2006.4.
