2X SPEED DOME CAMERA SCP-2120 User Guide Before installing and operating the camera, please read this user’s manual carefully.
The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Contents • • • • • Features…………………………………………………………………………… 6 Warnings & Cautions… ……………………………………………………… 7 Component Names and Functions………………………………………… 11 Components and Accessories……………………………………………… 12 Installing Your Camera… …………………………………………………… 14 ■ Speed Dome Camara and Appliances Wiring Diagram………… 14 ■ How to Set Up Protocols and ID DIP Switches…………………… 16 ■ Communication DIP Switch Settings (SW2)… …………………… 17 ▶ Protocol Settings……………………………………………………………………… 17 ▶ Baud Rate Settings…………………………………………………………
Features A/F 12X Optical Zoom Smart P/T The built-in 12X optical zoom lens with auto-focus is combined with a 16x digital zoom, providing a maximum of 192x zoom. The Smart P/T function automatically adjusts the control speed of the Pan and Tilt functions according to the current zoom ratio. It is useful to adjust the functions manually for detailed controls when monitoring at high zoom ratios.
Warnings & Cautions Warnings Cautions Stop using the camera if smoke or abnormal heat is detected. Do not install on your own. This installation should be made by a qualified service person. Installing this product on your own may result in fire or electric shock. For the installation service, contact the retail shop where you bought the product. May cause fire. Do not install in high humidity or in a place that may be exposed to oil or gas.
Warnings & Cautions Detailed Warnings and Cautions * Components - Avoid operating the camera for long durations under high temperatures and in high humidity. Excessive heat can shorten the lifespan of the camera components. - Do not install or place the camera near any heat sources. - Subjecting the dome cover to physical shock may damage the camera. - Do not place the camera facing direct sunlight or other intense light sources.
Components and Accessories Front Side Camera Wiring Interface Board For the camera wiring, please refer to the picture below. The camera's wiring interface board is fitted to the housing, this is sold separately. (When using coaxial communication, a separate control signal connection is not required.) Alarm Controller & Auxiliary Signal Connection Bottom 1 2 3 4 5 1 2 3 4 5 Screw Hole Communication Setup Switch ID Setup Switch Video/Communication/Power Alarm No. 1 2 3 4 5 6 7 8 Name 2.COM 2.
Installing Your Camera Speed Dome Camera and Appliances Wiring Diagram Connecting with the Samsung Techwin PC DVR Connecting with Samsung Techwin’s “Stand Alone DVR” · RS-485 : · RS-485 : Camera 485+ 485- Stand Alone DVR R+ R SVR-1670/1680/1660/1645/960/ Camera PC DVR 485+ 485- + - SVR-945 SVR-940/450 SVR-1650/1640A/950E SVR-9416/9116/9016 Connecting with the Samsung Techwin Controller SCC-3100A · RS-485 : SCC-3100A Data Box PORT1 Camera RX+ RXTX+ TX- SCC-3100A Data Box 485+ 485- Not
Installing Your Camera How to Set Up Protocols and ID DIP Switches You can control various settings of the camera system using the Communication and ID DIP switches. Before installing the product, please set up the DIP switches according to the installation environment. 1. Detach the camera frame from the install base, and place the bottom of the frame toward you as shown in the picture below. 2. S et the switches according to your installation environment.
Installing Your Camera • Camera ID Chart • Communication Response Settings Select a communication response method for the camera and controller: Response or No Response. Function Response Mode Switch SW2- #7 ON Response OFF No Response • Termination Settings To prevent the attenuation of communication signals between the camera and controller, the items at the end of line must be set up with the termination settings.
Installing Your Camera ID 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 SW1-#1 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF SW1-#2 ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF SW1-#3 OFF OFF ON ON ON ON OFF OFF OFF
Installing Your Camera ID 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 SW1-#1 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF SW1-#2 OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF
Installing Your Camera ID 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 SW1-#1 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON SW1-#2 ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON SW1-#3 O
Installing Your Camera Preparing and Installing Camera Bracket Installation Examples For the installation guidelines for the brackets and housings, refer to the user’s manual enclosed with the bracket or housing that is sold separately. • Camera Wiring Diagram - The pictures below show the front view of the camera installed with a wall or flush bracket. For more instructions on installing the camera, please refer to the following guidelines. RS-485 SVR Series 1 2 ...
Installing Your Camera On-Ceiling Mount Type Installation Example 1. Attach Template Attach the template on the ceiling, facing the “Front” mark to the main monitoring direction. Drill a hole in the ceiling according to the 60 mm diameter hole marked on the template, and then drop the camera cables down through the hole. 2. Mount Bracket Using the 4 screws, install the mount brackets on the ceiling, matching its directional guides with those of the template. 3.
Installing Your Camera 5. C onnect Cables Connect each camera cable to the proper terminals on the bottom of the camera. For more detailed instructions, please refer to Page 13:“Camera Wiring Diagram”. 6. C amera DIP Switch Setup DIP switches for communication and ID setup are located on the bottom of the camera. For more instructions, please refer to Page 16. Flush Mount Type Installation Example 1.
Installing Your Camera 3. Detach the Mount Housing Remove the 3 screws, and then detach the mount housing from the camera. 5. Install Camera Install Camera Fit the camera to the hole on the ceiling, and then secure the camera using 3 Product-enclosed Fixture Screws (M4x20). Ceiling Screw Screw 4. Connect Cables & Camera Setup Connect each camera cable to the proper terminals on the bottom of the camera (Refer to Page 13: “Camera Wiring Diagram”).
Interface Symbols • Motion Detection Standby/Operation Display : - When in standby mode, the " " in the upper right of the screen blinks and then changes to " " if motion is detected. • Alarm Input Port Status Display : - "①","②" in the upper right of the screen blink. • Current Alarm Port Display According to Input Alarm Ports(Priority) : - Only one of " "," " in the upper right of the screen blinks.
Operating Your Camera INTERNAL Sync LINE LOCK Others P1 Sharpness Color Freeze ON/OFF Preset Setting/Edit/Home Position/Execute/Clear/Status Pan Swing Setting/Execute/Clear Swing SEQ. Tilt Swing Setting/Execute/Clear P&T Swing Setting/Execute/Clear Group SEQ. Group1~6 Setting/Execute/Clear Tour SEQ. Setting/Execute/Clear PTZ Trace Trace1~4 Replay/Replay Once/Memorize/Clear OFF SCHEDULE Sunday~Saturday AutoPan Speed/Tilt A.
Operating Your Camera Camera ID Camera Name Preset Number Preset Name OSD Setting Sequence Status Area Name PTZ Position Language Others Alarm Enable Alarm Input ON/OFF ON/OFF Edit Camera Name ON/OFF ON/OFF Edit ON/OFF ON/OFF ON/OFF ENGLISH/CHINESE/FRENCH/GERMAN/SPANISH/ITALIAN/ PORTUGUES/KOREAN On/Off ON/OFF Direction Set North Dir.
Functional Description 1.2 Zoom Tracking ▶ Main Menu/Camera Setting/Focus & Zoom/Zoom Tracking Through this menu you can set up the camera’s focus mode when zooming. Main Menu Camera Setting Sequence Setting P/T Setting OSD Setting Alarm Setting Initialize Password Setting Status Mode : - AUTO : Auto-focuses when zooming. - TRACKING : Focuses manually when zooming. - OFF : Disable the focus modes when zooming. (Full manual mode) Speed : - SLOW/MEDIUM/FAST : Adjusts the zooming speed.
Functional Description 4. Backlight 3. Exposure ▶ Main Menu/Camera Setting/Exposure Main Menu Camera Setting Sequence Setting P/T Setting OSD Setting Alarm Setting Initialize Password Setting Status ➡ Camera Setting Zoom/Focus White Balance Exposure Back Light AGC SSNR SSDR Day/Night Others ATW OFF HIGH MEDIUM ➡ Exposure Brightness Iris Shutter Sens-Up The Exposure settings are to control the camera’s exposure meter. Brightness : Adjusts the screen brightness.
Functional Description 4.2 HLC ▶ Main Menu/Camera Setting/Back Light/HLC HLC masks strong light sources from the camera lens, blocking them from saturating the monitor screen. Main Menu Camera Setting Sequence Setting P/T Setting OSD Setting Alarm Setting Initialize Password Setting Status Level : Three HLC operation levels are available: LOW, MEDIUM, and HIGH. Mask Tone : Adjusts the masking brightness. 4.
Functional Description 5. AGC 6. SSNR (Samsung Super Noise Reduction) ▶ Main Menu/Camera Setting/AGC ▶ Main Menu/Camera Setting/SSNR AGC (Automatic Gain Control) adjusts the camera’s gain control and the screen brightness if the camera has captured an object under low-light conditions. The OFF, LOW, MEDIUM, HIGH, and MANUAL modes are available.
Functional Description 8. Day & Night 7. SSDR(Samsung Super Dynamic Range) ▶ Main Menu/Camera Setting/SSDR SSDR illuminates darker spots of an image while retaining the same light level for brighter spots to even out the overall brightness of the image with high contrast between bright and dark spots. Main Menu Camera Setting Sequence Setting P/T Setting OSD Setting Alarm Setting Initialize Password Setting Status ➡ ➡ SSDR ON SSDR OFF ATW BLC HIGH MEDIUM - Mode : Enables or disables SSDR.
Functional Description 9. Others Sequence Setting ▶ Main Menu/Camera Setting/Others Sync : - INTERNAL : S ynchronizes the camera’s output timing to the internal crystal. - LINE LOCK: S ynchronizes the camera’s output timing to the AC adapter power to synchronize multiple cameras. This option is useful when using a switch such as Matrix Switcher. - LINE LOCK PHASE : E nables setting the adapter’s synchronization phase between 0 and 360°. Image Adj : - Sharpness : Sharpens outlines of an image.
Functional Description 10.2 Preset Edit ▶ Main Menu/Sequence Setting/Preset/Edit You can edit the 13 preset items such as Pan/Tilt location, Main Menu Zoom and Focus, which are selected among camera functions. Camera Setting PTZ : Sequence Setting Recalls saved locations using the Preset Settings command. .... Focus Mode : ➡ Refer to the section entitled Setting Up Your Camera. Sequence Setting Preset Swing SEQ Group SEQ .... Brightness : Refer to the section entitled Setting Up Your Camera.
Functional Description 10.4 Preset Execution/Deletion/Memory Check ▶ Main Menu/Sequence Setting/Preset ▶ Main Menu/Sequence Setting/Swing SEQ Home Position : Sets one of the currently configured preset positions as the home position. Main Menu Camera Setting Sequence Setting P/T Setting OSD Setting Alarm Setting Initialize Password Setting Status Execute : Recalls a saved preset location. Clear : Deletes the selected preset location. Status : Opens a map of saved preset locations.
Functional Description 12. Group SEQ 13. Tour SEQ ▶ Main Menu/Sequence Setting/Group SEQ Selecting Group SEQ recalls a group of multiple preset locations in a consecutive manner. A group can contain up to 255 preset locations. Main Menu Camera Setting Sequence Setting P/T Setting OSD Setting Alarm Setting Initialize Password Setting Status Setting : Using the joystick, enter desired preset numbers into the PSET section. DWT indicates the camera’s duration of stay at a preset location.
Functional Description 14. PTZ Trace 15. Auto Run ▶ Main Menu/Sequence Setting/PTZ Trace Maximum 4 patterns of the manual operation paths (for Pan, Tilt, Zoom and Focus) are memorized and replayed. Main Menu Camera Setting Sequence Setting P/T Setting OSD Setting Alarm Setting Initialize Password Setting Status Replay : Replays a route saved by the Trace function. Use the Stop button to stop the replay. Replay Once : Replays a saved Trace route once.
Functional Description 16. Schedule 17. Power On Resume and MD Dwell Time Schedule enables you to schedule a sequencing action by day and time. Auto Run Mode Time SCHEDULE 30 SEC ➡ Schedule Set Sunday Monday Tuesday Wednesday Thursday Friday Saturday ON OFF OFF OFF OFF OFF OFF Select Day : At Auto Run, select SCHEDULE to set up each day of the week, as shown on the side picture. Select a day, change to ON, and then press Enter.
Functional Description P/T Setting 19. Tilt Limit ▶ Main Menu/P/T Setting/Pan/Limit 18. Pan Limit ▶ Main Menu/P/T Setting/Pan Limit The moving ranges in the Pan directions can be limited. Main Menu Camera Setting Sequence Setting P/T Setting OSD Setting Alarm Setting Initialize Password Setting Status Position : Selecting the Position menu brings up the following screen if it is for the Pan Limit setting. Move the joystick left and right to select a movement range from the starting point to the end.
Functional Description 20. Area Setting ▶ Main Menu/P/T Setting/Area Setting The Area Setting menu enables selecting certain locations in Main Menu the course of the Pan and Tilt operation, and then display the Camera Setting areas with the OSD (On Screen Display) texts when the camera Sequence Setting passes through them. Up to 8 areas can be selected. P/T Setting Area Name : OSD Setting Alarm Setting You can add names to selected areas.
Functional Description 22. Prop. P/T 23. Digital Flip ▶ Main Menu/P/T Setting/Prop. P&T ▶ Main Menu/P/T Setting/Digital Flip This commands the camera to change the Pan and Tilt speed automatically according to the current zoom ratio. Moving the joystick clockwise (Tele) slows down and counterclockwise (Wide) accelerates the Pan and Tilt speed, allowing detailed adjustments. Turning this “Off” executes the function the optical 1x zoom speed regardless of how far the lens is zoomed in.
Functional Description 25. Jog Speed 24. Image Hold ▶ Main Menu/P/T Setting/Image Hold When the camera is moving between presets locations, this function freezes the cameras image until the camera reached the next location. This is useful to help the screen observer keep sharp eyes and to monitor multiple locations within a network.
Functional Description OSD Setting 26. Max Speed Level ▶ Main Menu/P/T Setting/Max Speed Level Adjusts the maximum speed of Pan and Tilt while performing the Preset and Sequencing actions. Main Menu Camera Setting Sequence Setting P/T Setting OSD Setting Alarm Setting Initialize Password Setting Status 27. OSD Setting ▶ Main Menu/OSD Setting Main Menu - Pan and Tilt operations can be set up to 650°/ sec.
Functional Description Alarm Setting 28. OSD Setting(Others) ▶ Main Menu/OSD Setting/Others OSD Setting is to set up the OSD (On Screen Display) functions. Direction : Indicates the current angle of the camera: East, West, South, North, Southeast, Southwest, Northeast, or Northwest. - Setting North Set up a North direction for the camera.
Functional Description Notes • As shown in the picture above, the Alarm Input must be entered with the Open or Closed switch signals. Supplying power without entering the signals may damage the product. P (Priority) : Set the priority of Alarm Inputs. If more than one alarm is simultaneously activated, the alarm with the highest priority activates before the others. Once the alarm is canceled, the next highest priority alarm activates.
Functional Description AUX Output menu is to operate the camera’s peripheral devices such as lamps and sirens through the controller and switches as well as through network communications. OUT Off 1,2 : - When an alarm event occurs, the output force can be terminated. NO COM AUX Off Main Menu COM AUX On Notes • Connecting the power connector and GND incorrectly to the Aux terminal’s NO and COM ports may cause a short circuit and fire, damaging the camera.
Functional Description Password setting Status 31. Password setting 32. Status ▶ Main Menu/Password setting The Password feature enables you to configure a password for rebooting the camera and accessing the OSD and preventing unauthorized modification of existing camera settings. ON/OFF : Enables or disables Password protection.
Troubleshooting Problem Controller does not work. No picture is displayed on monitor. The picture is too dark/ bright. The monitor displays a white image. Picture is out of focus. Cause and Solution ▶ Check if the camera and peripheral devices are properly connected. ▶ Verify the setups of ID, protocol, and baud rates. ▶ Check if power cable is securely connected to the camera and the monitor. Check if the video cable is properly connected.
Troubleshooting The camera's position differs from the position defined in a preset. Sequence configuration of the camera does not work. ▶ This phenomenon may happen, since the motors have a margin error of ±0.1˚. ▶ Check if Preset or another operation mode has been set. ▶ Check the Auto Refresh settings. Product Specification SCP-2120 51~54 77 The upper side of the picture is dark when the ▶ You are seeing the camera's internal camera is on the horizontal cover. The camera is functioning normally.
Product Specification AUTO(NTSC:1/60~120,000sec, PAL:1/50~120,000sec) / MANUAL / A.FLK RS485, Coaxial Communication STW, Pelco-D, Pelco-P, Pelco Coaxitron, Panasonic, Honeywell, AD, Vicon, SEC, BOSCH, GE 2 In, 2 Out ON/OFF -10°C to +50°C / 20% to 80% RH -20°C to +60°C / 20% to 95% RH AC24V ± 10% Max. 12W Ø154×150mm Approx. 1 kg 154mm 150mm Electronic Shutter Serial Com.
DECLARATION OF CONFORMITY Application of Council Directive(s) 2004/108/EC Manufacturer's Name SAMSUNG TECHWIN CO., LTD Manufacturer's Address SAMSUNG TECHWIN CO., LTD MEMO 42, SUNGJU-DONG CHANGWON-CITY, KYUNGNAM, KOREA, 641-716 European Representative Name European Representative Address Equipment Type/Environment Speed Dome Camera Model Name SCP-2120 Beginning Serial NO. C3Z4 Year of Manufacture 2009.1.
SALES NETWORK • • AMSUNG TECHWIN CO., LTD. S 145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si Gyeonggi-do, Korea, 462-703 TEL : +82-31-740-8151~8 FAX : +82-31-740-8145 AMSUNG TECHWIN AMERICA Inc. S 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 www.samsungcctvusa.com www.samsungtechwin.com www.samsungsecurity.com • AMSUNG TECHWIN EUROPE LTD.
