High Resolution 37x Weatherproof Camera User Manual SCO-2370
safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
safety information 7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock. 9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.) 10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock. CAUTION 1.
important safety instructions contents 1. Read these instructions. INTRODUCTION 2. Keep these instructions. 8 3. Heed all warnings. 4. Follow all instructions. Features What’s included Component names and functions 13 14 15 16 Connecting to Monitor Connecting to Power RS-485 Communication control Using Coaxial Communications 17 18 Menu Configuration Menu Setup 38 Troubleshooting 39 41 Specifications Dimension 42 STW Protocol Command Description 5. Clean only with dry cloth. 6.
introduction WHAT’S INCLUDED y 37x Optical Zoom The built-in SCO-2370 optical zoom lens is a highly durable component. It features auto focus, auto iris, and zoom functions. Check if the following items are included in the product package. y High Resolution By adopting a diagonal 1/4” 410,000 (NTSC) pixel, 470,000(PAL) pixel SONY CCD, the camera produces clear picture quality with a horizontal resolution of 600TV lines for color and a horizontal resolution of 700TV lines for BW mode.
introduction COMPONENT NAMES AND FUNCTIONS Back Front ➋ ● INTRODUCTION ❶ ➌ ➍ ڋڒ ڎڍ ڈڪ ➎ ڞڮ ➏ ❶ ➊ Camera Sunshield ➋ Sunshield adaptor : Fixing the sunshield onto the camera. ➌ Lens ➍ Video Output Terminal to Monitor : Used for monitoring of video output When ➋ ➌ ➍ camera installation. ➎ Function Setup Switch : Display the menu on the screen and move the cursor to four directions to confirm status or after changing a selected item.
introduction installation & connection COMPONENT NAMES AND FUNCTIONS CONNECTING TO MONITOR Please connect the video output terminal located on the back of the camera to the monitor. Heater & Fan ● INSTALLATION & CONNECTION This product is equipped with a built-in heater & fan that helps maintaining operational temperature and humidity. Monitor Fan CCD Camera Front cover Heater y The connection method varies depending on the type of monitor and accessories.
installation & connection RS-485 COMMUNICATION CONTROL CONNECTING TO POWER The recommended adaptor specification for SCO-2370N/P is AC 24V/1.5A over. Please check the standard power requirement before connecting the power. Connecting to RS-485 Control Cable SPEC WHITE RS-485+ BLUE RS-485- Using RS-485 communication will enable you to control the OSD menu from a SAMSUNG TECHWIN System Controller or DVR. (1) Connection to a PC.
installation & connection setup USING COAXIAL COMMUNICATIONS MENU CONFIGURATION y Coaxial Communications System MAIN SETUP MENU y OSD Control method DVR CONTROLLER SET MENU/ENTER OSD KEY UP UP KEY JOYSTICK UP DOWN DOWN KEY JOYSTICK DOWN LEFT LEFT KEY JOYSTICK LEFT RIGHT RIGHT KEY JOYSTICK RIGHT ● OFF ● ON ● ATW ● MANUAL ● OUTDOOR ● INDOOR BACKLIGHT ● OFF ● BLC MOTION DET ● OFF ● ON ● MODE ● ZOOM TRACK ● ZOOM SPEED ● D-ZOOM ● ZOOM POS INIT ● USER PRESET ● LENS INIT ●
setup SSDR (Samsung Super Dynamic Range) MENU SETUP SSDR illuminates darker spots of an image while retaining the same light level for brighter spots to even out the overall brightness of images with high contrast between bright and dark spots. Use the Function Setup switch within the camera. Function Setup switch 2. Use the switch to change the SSDR level according to the contrast between bright and dark areas. 1. Press the Function Setup switch for 2 seconds.
setup M White Balance may not work properly under the following conditions. In this case select the AWC mode. ➊ When the color temperature of the environment surrounding the subject is out of the control range (e.g. clear sky or sunset). ➋ When the ambient illumination of the subject is dim. ➌ If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, the White Balance operation may become unstable.
setup y HLC : Enable the user to change the level, mask tone area. MOTION DETECTION HLC SETUP 䯝LEVEL MASK TONE MIDDLE IIIIIIIIIIIIIIIIIIIIÂIIIIIIIIIIIIIIIIIIIII 7 1. When the SETUP menu screen is displayed, select ‘MOTION DETECTION’ by using the Function Setup switch so that the arrow indicates ‘MOTION DETECTION’. M For effective viewing of license plates, there is a minimum required illumination and the shutter speed needs to be faster than 1/200sec.
setup y START ZOOM : By moving the Function Setup switch in the ‘SMART ZOOM’ item to select the zoom position from 1x to 37x to be returned after the ‘SMART ZOOM’ action is over. SMART ZOOM SETUP X1 X5 5 SEC y DWELL TIME : Use the Function Setup switch in the ‘DWELL TIME’ item to select a time between 5 and 60 seconds for the dwell time before the zoom is returned to the ‘SMART ZOOM’ position.
setup y ZOOM SPEED : Configure zoom tracing speed using this feature. Position the indicator over ‘ZOOM SPEED’ using the Function Setup switch and then set to desired mode using the Function Setup switch. - FAST : To move zoom fast. - SLOW : To move zoom slowly. - MEDIUM : To move zoom at medium speed. y D-ZOOM : Configure magnification limit from x2~x16 using this feature.
setup EXPOSURE 2. Press the Function Setup switch to confirm. y BR IGHTNESS : Use this feature to adjust image brightness. Position the indicator over ‘BRIGHTNESS’ using the Function Setup switch. Then increase or decrease brightness level using the Function Setup switch while verifying the changes on screen. Set END once desired level is obtained. y IRIS : Set ‘IRIS’ to ‘AUTO’ or ‘MANUAL’.
setup y SSNR3 (Samsung Super Noise Reduction): On screen noise reduction. SPECIAL - LOW : Low noise reduction - MEDIUM : Medium noise reduction - HIGH : High noise reduction - OFF : Disabled 2. Press the Function Setup switch to confirm. M Changing the ‘AGC’ setting from LOW to HIGH results in greater sensitivity, as well as on screen noise. Setting ‘AGC’ to OFF locks ‘SSNR3’ configuration. y SENS-UP : This feature ensures clear images at night or under low light conditions.
setup y DAY/NIGHT : You can display pictures in color or black and white. ➋ Select a desired mode using the Function Setup switch according to the picture display you want. # PRIVACY 䯝 DAY/NIGHT DIS SYNC COMM ADJ IMAGE ADJ MONITOR DISPLAY RETURN OFF AUTO OFF INT 5 SEC SLOW - DWELL TIME : You can select tday/ night switching delay time from. p 5,7,10,15,20,30,40, 60(sec) - DURATION : You can select the day/night switching point(lux). Slow Color p B/W B/W p Color 2.6Lux 4.2Lux 1.2Lux 6.
setup - H-REV : You can flip the picture horizontally on the screen. CONTROLLER ڋ ڒڎڍڈڪڞڮ CONTROLLER ڋ ڋ ڒڎڍڈڪڞڮ - SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer. ڒڎڍڈڪڞڮ M When the SHARPNESS level is too high, video output may be unnatural or noisy. OFF OFF ON V-REV SHARPNESS RETURN ● SETUP ڋ ڒڎڍڈڪڞڮ - V-REV : You can flip the picture vertically on the screen.
setup - USER : Please use this menu item when using a monitor other than standard ones. You can change the gamma, PED level, and color gain in the sub menus. USER MONITOR SETUP 䯝GAMMA 0.55 PED LEVEL IIIIIIIIÂIIIIIIIIIIIIIIIIIIIII 17 COLOR LEVEL IIIIIIIIIIIIIIIIIÂIIIIIIIIIIII 50 M Correcting Mistakes RETURN y DISPLAY : Use this feature to designate a name for the camera, which will display on the monitor screen. - CAM TITLE : If the camera is named, it is displayed on the monitor.
troubleshooting specifications TROUBLESHOOTING SPECIFICATIONS SCO-2370N If the product does not function properly, please see the below for trouble shooting. SCO-2370P POWER PROBLEM The image on the screen is dim. The image on the screen is dark. The camera is not working properly, and the surface of the camera is hot. f Check that the power cord and line connection between the camera and monitor are fixed properly.
specifications DIMENSION SCO-2370N SCO-2370P On / Off ( 8 Area ) Privacy Function On / Off (12 Areas, Rectangle Type ) Sens-up (Frame Integration) Auto / Off (Selectable x2 ~ x512) Gain Control Low / Medium / High / Manual / Off White Balance AWC/Manual/Outdoor/Indoor/ATW (1700°K~11,000°K) Electronic Shutter Speed 1/60 ~ 1/1200,000 Digital Zoom On / Off (2x ~ 16x) Flip / Mirror On / Off Communication RS-485 & Coaxial Control (Pelco Coaxitron) Protocol Samsung-T, Samsung-E, Pelco-D, Pelco
STW protocol command description STW PROTOCOL COMMAND DESCRIPTION Reset Byte2 Byte3 Command Packet STX CAM ID HOST ADDR Return Packet STX CAM ID HOST ADDR Checksum CHECKSUM CALCULATION : UNARY OPERATION OF SUMMAT ION FROM BYTE2 TO BYTE9. EX) CHECKSUM = ~(BYTE2+BYTE3+... +BYTE8+ BYTE9); Function Reset all data to factory default value.
STW protocol command description Function ZOOM Direct A0h CAM ID HOST ADDR 00FFh P1 P2 P3 00h AFh CHECK SUM Return Packet A0h CAM ID HOST ADDR 00FFh P1 P2 P3 00h AFh CHECK SUM Parameter P1, P2 : OPTICAL ZOOM = 0000h~06EAh P3 : DIGITAL ZOOM = ((256*10)/Ratio)-1 EX) D-ZOOM 1.1x : P3 = E7h = ((256*10)/11)-1, Ratio 11 me ans 1.1x. D-ZOOM 2.0x : P3 = 7Fh = ((256*10)/20)-1, Ratio 20 me ans 2.0x. Function Stop zoom & focus lens moving.
STW protocol command description Function Display OSD menu on the screen. Clear OSD menu and save current menu setup. Command Packet A0h CAM ID HOST ADDR 00B1h P1 00h 00h 00h Afh CHECK SUM Return Packet A0h CAM ID HOST ADDR 00B1h P1 00h 00h 00h Afh CHECK SUM OSD Menu On/Off P1 : 00h = ON 01h = OFF Function Move OSD arrow to up.
MEMO DECLARATION OF CONFORMITY Application of Council Directive(s) 2004 / 108 / EC Manufacturer's Name SAMSUNG TECHWIN CO., LTD Manufacturer's Address SAMSUNG TECHWIN CO., LTD 42, SUNGJU-DONG CHANGWON-CITY, KYUNGNAM, KOREA, 641-716 European Representative Name European Representative Address Equipment Type/Environment CCTV Camera Model Name SC0-2370P Beginning Serial NO. C54N6V3Z300001X Year of Manufacture 2010.03.
MEMO MEMO
MEMO MEMO
MEMO MEMO
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60, FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222, FAX : +1-310-632-2195 www.samsungcctvusa.com www.samsungtechwin.com www.samsungsecurity.com SAMSUNG TECHWIN EUROPE LTD.