Supreme Resolution WDR Camera User Manual SCB-5003
Supreme Resolution WDR Camera User Manual Copyright ©2014 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document.
Before operating the camera, confirm the camera model and correct input power voltage. To help you understand this manual thoroughly, we'll introduce our model description.
safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the camera. doing so may cause personal injury due to fire, electric shock, or falling objects. 8. If any unusual smells or smoke come from the unit, stop using the product. in such case, immediately disconnect the power source and contact the service center. continued use in such a condition may cause fire or electric shock. 9.
safety information FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation. CAUTION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules.
important safety instructions 1. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug.
contents introduction 9 10 11 13 Features Components and Accessories Overview Lens connection 16 16 17 18 Connecting to Monitor Connecting to Power Control via RS-485 Interface Using Coaxial Communications camera operation 19 19 Menu Configuration Menu Setup troubleshooting 36 Troubleshooting specifications 37 39 Specifications Dimension 9 16 19 36 37 _ contents
introduction Features Excellent Sensitivity The built-in high sensitivity COLOR CMOS produces a clear image. - Color : 0.03Lux (F1.2, 50IRE), 0.001Lux (1sec, F1.2, 50IRE) 0.01Lux (F1.2, 30IRE), 0.0003Lux (1sec, F1.2, 30IRE) B/W : 0.003Lux (F1.2, 50IRE), 0.0001Lux (1sec, F1.2, 50IRE) 0.001Lux (F1.2, 30IRE), 0.00003Lux (1sec, F1.2, 30IRE) Intelligence Without an external sensor, you can use this product to detect motion and generate alarms and thus more efficient monitoring can be achieved.
introduction Video/DC Drive Lens Support You can select Video or DC Drive Lens from the menu. DIS (Digital Image Stabilizer) The DIS function compensates for any camera movement, to produce more stable pictures. Miscellaneous Functions HLC(High Light Compensation), REVERSE , D-ZOOM, SHARPNESS and PRIVACY functions are provided. Communication Coaxial and RS-485 communication methods are supported.
Overview Front View ● introduction 1 2 4 3 ❶ Tripod Mounting Bracket Screw Hole : U sed to fix the camera on a bracket. The screw sizes for this hole are as follows. 1/4"-20 UNC (20 THREAD) L:4.5mm±0.2mm (ISO standard), or 0.197" (ASA standard) 2 Back Focus Control Lever : It acquires margins for lens adjustments. 3 Lens adaptor : IInstall this if you use the lens. 4 Auto Iris Lens Connector : Used to connect Auto Iris Lens plug.
introduction Rear View 1 VIDEO POWER 2 3 4 5 6 7 8 1 Function Setup switch Display the menu on the screen and move the cursor to four directions to confirm ststus or after changing a selected item. 2 Power LED : This lamp is lit when the camera is receiving power normally. 3V ideo OUT Terminal : Sends video signal and connects to the video input terminal of the monitor. ower input terminal : Connect the designated power supplies.
Lens The lens is not supplied with this camera. Purchase a lens suitable for your environment. This camera accepts the auto iris lens and both C-and CS-mount lens. T o use the functions of this camera effectively it is recommended that a DC type Auto Iris lens is used. Keep the lens surface clean, if it becomes contaminated with dirt or fingerprints the picture quality suffers. When Using Auto Iris Lens 1. Strip the insulation of the auto iris lens cable 8mm from the end. approx. 8mm 2.
introduction LE TE NEA R 4. Fit the cover of the auto iris lens connector plug, remove the protective glass cover from the front of the camera, and fasten the auto iris lens by turning it clockwise. Me ga Pie x 5. After combining the lens, adjust the focus. When Using a C/CS-Mount lens (Sold separately) Before installing a lens, identify whether the lens to be installed is a C-Mount or CS-Mount. This camera is set for a CS-Mount Lens by default.
M Use the lens connector shown in the following figure. If the dimensions of the connector are not correct, it may damage the camera, or the lens may not be installed firmly. there may be problems. Use a lens that weighs less than 450g. When adjusting the Automatic Level Control (ALC) of an auto iris lens, use Av mode if available. If you use the Pk mode, the picture brightness may change continuously. C-Mount Lens: 10mm or less CS-Mount Lens: 5mm or less When Using a C-Mount Lens 1.
connection Connecting to Monitor Connect the Video OUT port on the rear panel of the camera to a monitor. VIDEO POWER Monitor SCB-5003 A s the connecting method varies with the instruments, refer to the manual supplied with the instrument. Only connect the cable when the power is turned off. Connecting to Power You can connect power as shown in the following figure. Since the power specification supports both AC and DC, connect AC 24V, 500mA Adaptor or DC 12V, 500mA Adaptor.
When the resistance value of copper wire is at [20°C(68°F)] #24 (0.22mm2) #22 (0.33mm2) #20 (0.52mm2) #18 (0.83mm2) Resistance value(Ω/m) 0.078 0.050 0.030 0.018 Voltage Drop (V/m) 0.028 0.018 0.011 0.006 A s shown in the table above, voltage decreases as the wire gets longer. Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera.
connection Using Coaxial Communications Coaxial Communications System OSD Control method CAMERA DVR SET MENU/ENTER CONTROLLER OSD KEY UP UP KEY JOYSTICK UP DOWN DOWN KEY JOYSTICK DOWN LEFT LEFT KEY JOYSTICK LEFT RIGHT RIGHT KEY JOYSTICK RIGHT DVR ALARM HDD 1 DVD RECORDE R NETWORK 2 BACKUP 3 REC REC 4 5 6 7 9 10 11 12 13 14 15 16 8 ZOOM FREEZE BACKUP SEARCH TELE WIDE MODE AUDIO VIEW ALRAM OPEN/CLOSE PRESET MENU USB RETURN MENU SEARCH MULTI REC MENU PRE
camera operation Menu Configuration MAIN SETUP ● DAY/NIGHT ● INDOOR ● BACKLIGHT ● USER SSDR ● ON ● OFF WHITE BAL ● ATW ● MANUAL ● OUTDOOR ● AWC SET ● INDOOR ● MERCURY EXPOSURE ● BRIGHTNESS ● AGC ● LENS ● SSNR4 ● SHUTTER ● RETURN BACKLIGHT ● OFF ● WDR ● USER BLC ● HLC SPECIAL ● DISPLAY ● DAY/NIGHT ● DIS ● COMM ADJ ● IMAGE ADJ ● DEFOG ● PRIVACY ● VIDEO ANALYTICS ● RETURN EXIT ● SAVE ● NOT SAVE ● RESET Menu Setup Use the Function Setup switch within the camera.
camera operation MAIN SETUP Select the function using the Function Setup switch. ▶ 1. PROFILE 2. SSDR 3. WHITE BAL BASIC Change the status using the Function Setup switch. ON ATW 4. EXPOSURE 5. BACKLIGHT OFF 6. SPECIAL 7. EXIT SAVE 1. Press the Function Setup switch. Main SETUP menu is displayed on the monitor screen. 2. Select a desired function using the Function Setup switch. Place the cursor over a desired item. 3. Set up a selected item by using the Function Setup switch. 4.
3. In the PROFILE menu, you can confi gure the following camera settings at once. BASIC DAY/NIGHT BACKLIGHT ITS INDOOR USER SHUTTER ATW ATW ATW MANUAL(1/200) A.FLK - AGC HIGH HIGH HIGH HIGH HIGH - WHITE BAL ATW ATW ATW OUTDOOR INDOOR - BACKLIGHT OFF OFF USER BLC OFF OFF - SSNR4 ON ON ON ON ON - DAY/NIGHT AUTO AUTO AUTO AUTO AUTO - M If you select the traffic monitoring mode, the shutter will be set to 1/200 sec. Noise can be detected at night.
camera operation White Bal (White Balance) Use the White Balance function to adjust the screen color. 1. When the SETUP menu screen is displayed, select ‘White Bal’ by using the Function Setup switch so that the arrow indicates ‘White Bal’ . 2. Select a desired mode using the Function Setup switch. MAIN SETUP 1. PROFILE 2. SSDR ▶ 3. WHITE BAL BASIC ON ATW ※ Select one of the following 6 modes, as appropriate for your purpose.
EXPOSURE 1. W hen the SETUP menu screen is displayed, select ‘EXPOSURE’ by using the Function Setup switch so that the arrow indicates ‘EXPOSURE’. BRIGHTNESS : Adjusts the video brightness. LENS : U sing this function, you can control the screen brightness. EXPOSURE SETUP -------▶ 1. BRIGHTNESS 2. LENS 3. SHUTTER 4. AGC 5. SSNR4 6. RETURN 50 DC HIGH ON - DC/VIDEO : Select Auto Iris Lens. djusts the Iris control speed of the DC lens.
camera operation SHUTTER : You can select the shutter. - MIN : 1 ~ 1/12000 - MAX : 1/60 ~ 1/12000 - A.FLK : Select this when you experience picture flicker, this happen when there is a clash with the installed lighting frequency. M The greater the shutter value the brighter the screen is but the more the residual images of objects there are. If the min shutter value is large, it can cause noise, spots and white areas but still operate normally.
M If the white balance menu is set to manual, then HLC performance can be limited. If you use the defog and HLC functions at the same time, saturation can occur in a bright environment. Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen, optimize the installation angle for the best HLC performance. When dark, the HLC is only activated when a bright light exceeding a specifi c size. (In NIGHT ONLY mode).
camera operation SPECIAL 1. W hen the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function Setup switch so that the arrow indicates ‘SPECIAL’. 2. Select a desired mode using the Function Setup switch. DISPLAY ❶ If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates ‘DISPLAY’. ❷S elect a desired mode using the Function Setup switch. SPECIAL SETUP ▶ 1. DISPLAY 2. COMM ADJ 3. IMAGE ADJ 4. DAY/NIGHT 5. DEFOG 6. PRIVACY 7. DIS 8.
- DISP ID : Display camera title on top left corner of the screen. - FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue) - LANGUAGE : You can select the menu language according to your requirements. COMM ADJ (Communication Adjustment) : This function sets up the camera communication status when controlling the camera through an external control device. ❶ I f the SPECIAL menu screen is COMM SETUP displayed, use the Function Setup SAMSUNG-T ▶ 1.
camera operation - PED LEVEL : T he setting range is 1 ~ 100. The closer to 100 the setting is, the higher the PED level gets. - COLOR GAIN : T he setting range is 1 ~ 100. The smaller the setting value is the smaller the color gain gets and the more color blind it gets. - H-REV : F lip an image horizontally. - V-REV : F lip an image vertically. - D-ZOOM : Y ou can use a digital zoom of x1 ~ x16. - SHARPNESS : Select a mode to adjust the thickness of an image’s sharpness.
DURATION : This function is used to select the brightness of light where switching occurs. GAIN LEVEL LOW MID HIGH B/W→Color Color→B/W B/W→Color Color→B/W B/W→Color VERY SLOW 2.4 5.2 1.5 5.6 0.6 6.2 SLOW 2.5 5 1.8 5.4 1.1 6 NORMAL 2.6 4.9 2.1 5.2 1.6 5.8 FAST 2.7 4.8 2.4 5 2.1 5.4 VERY FAST 2.8 4.7 2.7 4.8 2.6 5 ※D epending on the installation environment and the exposure menu’s gain mode setting, the switching brightness may vary.
camera operation M If the defog mode is set to Auto, and if the amount of fog is reduced, the function level will be also reduced. If you want to maintain the same level of defogging, set it to Manual. If there is little fog and the manual fog level is high, the screen contrast can get high. PRIVACY : Mask an area you want to hide on the screen. ❶ I f the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates ‘PRIVACY’.
M In the following cases, the initially set tampering detection function can malfunction. - In a monitoring environment with a simple background or an environment with low light level or at night, the detection performance can deteriorate. - Sudden changes in the lighting and severe camera shaking can be wrongly detected as tampering. - I mmediately after tampering, the camera tampering detection can take up to a max of five seconds.
camera operation NON DET. AREA : S pecify a detection exception area to mask.Select a mask area number and specify the size and position. EL AREA : You can select up to 4 areas. S etermines whether to use the area selected in the AREA. MODE : D TOP/BOTTOM/LEFT/RIGHT : Adjust the size and position of the selected area. RETURN : Return to the MOTION DET menu. INDICATOR : If an object moves in a pattern set by the user, it will be displayed on the screen as a box.
1) LINE FENCE - SEL POS : Selects a position from POS1,POS2. - DIRECTION LINE FENCE --------------- POS1 50 1 RIGHT RIGHT : Detects objects moving left to right on the fence line. LEFT : D etects objects moving right to left on the fence line. RIGHT/LEFT : D etects all objects moving crosswise on the fence line. - RETURN : Return to the VIRTUAL FENCE menu. 2) AREA FENCE - SEL POS : Selects a AREA FENCE position from ▶ 1. SEL POS POS1 POS1 ~ POS4. -------2.
camera operation ALARM OUT : When object movement is detected, the detection signal will be outputted. EXTERNAL : Send signals through external terminals. OSD : Display signals on the screen. RETURN : Return to the INTELLIGENCE menu. RETURN : Return to the VIDEO ANALYTICS menu. M Before use, set the max/min movement size within the range. Depending on the shape of an object, there can be errors in size detection.
EXIT Select a desired EXIT mode using the Function Setup switch depending on the camera purpose. NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu. RESET : Revert camera to factory settings. (The language, communication and lens settings will remain the same). English_35 ● Camera Operation SAVE : Save the current settings and exit the MAIN SETUP menu.
troubleshooting Troubleshooting If you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician. Problems Troubleshooting Nothing appears on the screen. Check that the power cord and line connection between the camera and monitor are properly connected. Check that you have properly connected BNC cable to the camera. Check the type of lens. The image on the screen is dim.
specifications Specifications SCB-5003N SCB-5003P Video 1/3” 1.3M CMOS Total Pixels 1312(H) x 1069(V) Effective Pixels 1305(H) x 1049(V) Scanning System Progressive Scan Synchronization Internal H : 15.734KHz / V : 59.94Hz Color : 1000 TVL Horizontal Resolution B/W : 1000 TVL Frequency H : 15.625KHz / V : 50Hz Min. Illumination Color : 0.03Lux (F1.2, 50IRE), 0.001Lux (1sec, F1.2, 50IRE) 0.01Lux (F1.2, 30IRE), 0.0003Lux (1sec, F1.2, 30IRE) B/W : 0 .003Lux (F1.2, 50IRE), 0.0001Lux (1sec, F1.
specifications SCB-5003N SCB-5003P Digital Image Stabilization Off / On Tampering Off / On Motion Detection Off / On Intelligent Video Fence, Apear_Disappear, Counting ( Off / On ) Privacy Masking Off / On (24 programmable zones with 4points polygonal masking) Gain Control Off / Low / Middle / High White Balance ATW / Outdoor / Indoor / Manual / AWC / MERCURY (1,800K° ~ 10,500K°) Electronic Shutter Speed 1 sec ~ 1/12,000 sec Digital Zoom Off / On (1x ~ 16x) Reverse Off / H-Rev / V-Rev / H
Dimension Unit: mm ● specifications English_39
MEMO
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsung Techwin R&D Center, 6, Pangyo-ro 319beon-gil, Bundang-gu, Songnam-si, Gyeonggi-do 463-400, Korea TEL : +82-70-7147-8740~60, FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free : +1-877-213-1222 Direct : +1-201-325-6920 Fax : +1-201-373-0124 www.samsungcctvusa.com www.samsungtechwin.com www.samsungsecurity.com SAMSUNG TECHWIN EUROPE LTD.
