DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 41 Write the model and serial number here: Model # Serial # These numbers can be found inside on the left of the refrigerator. OWNER’S MANUAL AND INSTALLATION CONTENTS SAFETY WARNING SIGNS...............................................................2 OPERATING INSTRUCTIONS ........................................................4 SETTING UP THE REFRIGERATOR ........................................................ 4 MAJOR FEATURES...............................
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 2 SAFETY WARNING SIGNS • Before operating the appliance, please read this manual thoroughly and retain it for your reference. • Because these following operating instructions cover various models, the characteristics of your refrigerator may differ slightly from those described in this manual • The appliance is not intended for use by children or infirm persons without adult supervision.
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 3 CAUTION SIGNS Do not overfill the refrigerator with food. • When you open the door, an item may fall out and cause personal injury or material damage. Do not put bottles or glass containers in the freezer • When the contents freeze, the glass may break and cause personal injury. If the wall socket is loose, do not insert the power plug. • There is a risk of electric shock or fire. Do not disconnect the power cord by pulling on it.
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 4 SETTING UP THE REFRIGERATOR Once you have performed the following steps, your refrigerator should be fully operational. If not, check the power supply and electricity source. If you have any questions, contact your SAMSUNG service center. Place the refrigerator in an appropriate location with reasonable clearance between the wall and the refrigerator.
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 5 CONTROL PANEL OPERATING INSTRUCTIONS Double Line Display ICE TYPE BUTTON Use this button to choose Cubed or Crushed ice or Ice off. POWER FREEZE BUTTON Speeds up the freezing process in the freezer. FREEZER TEMP. BUTTON To set the freezer temperature, press the button repeatedly to change the set temperature in sequence between cold and coldest. CHILD LOCK BUTTON When this button is pressed for 3sec.,all functions are locked and can not be modified.
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 6 CONTROL PANEL Single Line Display FRIDGE TEMP. BUTTON To set the fridge temperature, press the button repeatedly to change the set temperature in sequence between cool and coolest. ICE TYPE BUTTON Use this button to choose Cubed or Crushed ice or Ice off. FREEZER TEMP. BUTTON To set the freezer temperature, press the button repeatedly to change the set temperature in sequence between cold and coldest. LIGHT BUTTON Use this button to light up the dispenser.
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 7 CONTROL PANEL OPERATING INSTRUCTIONS Mono Line Display FRIDGE TEMP. BUTTON To set the fridge temperature, press the button repeatedly to change the set temperature in sequence between cool and coolest. ICE TYPE BUTTON Use this button to choose Cubed or Ice off. FREEZER TEMP. BUTTON To set the freezer temperature, press the button repeatedly to change the set temperature in sequence between cold and coldest.
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 8 DIGITAL PANEL Double Line Display Power Freeze • This light is will turn on when you press the Power Freezer button. Power Freeze speeds up the freezing process. • If you select Power Freeze, interior temperature of the freezer will decrease for 2 hr.30 min. • Press the Power Freeze button again to cancel the Power Freeze function. If you use this function, energy consumption will increase. Please turn off when not using this function.
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 9 DIGITAL PANEL Cubed Ice, Crushed Ice and Ice Off • Press the Ice Type button in sequence to choose Cubed Ice, Crushed Ice or Ice Off to stop making ice. • An indicator will light to show the ice type currently chosen. Light Button • Use this button to light up the dispenser.
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 10 DIGITAL PANEL Mono Line Display Cubed Ice and Ice Off • Press the Ice Type button in sequence to choose Cubed Ice or Ice Off to stop making ice. • An indicator will light to show the ice type currently chosen. Light Button • Use this button to light up the dispenser.
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 11 TEMPERATURE CONTROL Cool Down Period • To ensure safe food storage, allow the refrigerator to operate with the doors closed for 8 to 12 hours before loading it with food. Temperature Adjustment • After 24 hours, adjust the controls as needed. Adjust temperature gradually: push the button in small increments, allowing the temperature to stabilize. • Press the button(Freezer Temp or Fridge Temp) repeatedly until the desired set temperture.
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 12 SHELVES and BINS • Because these following operating instructions cover various models, the characteristics of your refrigerator may differ slightly from those described in this manual.
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 13 FROZEN FOOD STORAGE IN FREEZER Xtra SpaceTM • Can be used for frozen foods such as pizza, pasta, burritos, and fajitas. • In order to prevent odor penetration to the ice, stored food should be wrapped securely. NOTE To keep more food in the freezer • First, remove the ice bucket by lifting it up and sliding out. • Second, remove the Xtra Space cover by pushing it down and pilling it frontward.
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 14 FOOD STORAGE GUIDE CHILLED FOOD STORAGE IN REFRIGERATOR Tempered Spill Proof Glass Shelf • Can be used to store all types of chilled food. • Safe and break resistant. • Circular marks on the glass surface are a normal phenomenon. Fruit & Vegetable Drawer (Upper and Lower) • Used to store fruits and vegetables. • The drawer is airtight. Optimized humidity control design helps to preserve the freshness of stored vegetables and fruits.
DA99-00810A-0.6(EN) 3/14/07 11:51 AM Page 15 REMOVING THE FREEZER ACCESSORIES Ice Maker Bucket • Remove the bucket by lifting up and pulling out. Wire Shelf • Pull the shelf out as far as it goes. Then lift it up and remove it. • Hold the door bin with both hands and then lift it up. Wire Drawer • Remove the drawer by pulling it out and lifting it up slightly. • NOTE Do not use excessive force when removing the cover. It may cause an injury.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 16 CLEANING THE ACCESSORIES Interior • Clean the accessories with a mild detergent, then wipe out with a dry cloth. • After washing the accessories, make sure that they are dry before using them again. Exterior • Wipe the digital panel and display panel with a clean cloth. • The surface of doors, handles and cabinet should be cleaned with a mild detergent and soft cloth, then wipe off the surface with a dry cloth.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 17 CHANGING THE INTERIOR LIGHT INTERIOR LIGHT IN THE FREEZER. The freezer light is located in the bottom of the auger motor case. Use a screwdriver to remove the light cover (➀). Replace the bulb with a new one (➁) Reattach the light cover. WATER FILTER The water “Filter Indicator” light (on some model) • “Filter Indicator” light lets you know when it is time to change your water filter cartridge. The light will change from green to orange.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 18 INSTALLATION OF THE REFRIGERATOR Checking the Dimensions of your Entrance Door Check the dimensions of your entrance door to determine whether the refrigerator can pass through it. Model Dimension (inch) Width with hinge Case Height without hinge with door Depth without door RS25**** 908mm 1771mm 1750mm 869mm 749mm RS26**** 908mm 1771mm 1750mm 904mm 749mm Selecting the Location for the Refrigerator • Select a location with easy access to the water supply.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 19 INSTALLATION OF THE REFRIGERATOR How to assemble the seperable door handle (on some model) - Check the “UP” mark at the rear of the handle, and then place the handle in the right direction. OPERATING INSTRUCTIONS - Match the Handle Locking Tabs on the door and the hook of the handle, in upper and lower both side at the same time. Fix the handle pulling it down. - Check the right locking by pulling it up and down.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 20 REMOVING THE REFRIGERATOR DOORS Removing the Front Leg Cover Take hold of FRONT LEG COVER and lift it up. FRONT LEG COVER Separating the Water Supply Line from the Refrigerator Remove the water tube by pressing the coupler (➁) and pulling the water tube (➀) away. NOTE Be careful not to cut the water tube when separating it from the coupler.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 21 REMOVING THE REFRIGERATOR DOORS NOTE • Lift the door straight up. • Be careful not to pinch the water tubing and wire harness on the door. • Place doors on a protected surface. Removing the Freezer Door 1) With the door closed, remove the upper hinge cover (➀) along the arrow (➂) using a screwdriver, and then disconnect the wires (➁). 3) Remove the door from the lower hinge (➇) by carefully lifting the door (➈).
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 22 REMOVING THE REFRIGERATOR DOORS Removing the Refrigerator Door 1) With the door closed, remove the upper hinge cover (➀) along the arrow (➁) using a screwdriver. 2) Remove hinge screws (➂), and take off the upper hinge (➃) in the direction of the arrow (➄). Take care when removing the door to ensure that it does not fall on you. 3) Remove the door from the lower hinge (➅) by lifting the door (➆).
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 23 REATTACHING THE REFRIGERATOR DOORS Reattaching the Freezer Door 1) Reattach the freezer door by inserting the hose (➀) in the lower side of the door into the hole in the lower hinge (➁) and pull the hose down. 3) Connect the wires. 4) Put the front part of the upper hinge cover (➆) on the front part of the upper hinge (➇) and reattach from the front part of the upper hinge cover first.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 24 REATTACHING THE REFRIGERATOR DOORS Reattaching the Refrigerator Door 1) Insert the lower hinge (➀) in the bracket lower hinge (➁). 2) Place the hole in the refrigerator door (➂) over the lower hinge (➃). 3) Insert the upper hinge shaft (➄) into the hole (➅). After leveling between the upper hinge hole and the cabinet hole. Reattach hinge screws (➆) and gound screw (➇) in the clockwise direction.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 25 REATTACHING THE REFRIGERATOR DOORS Reattaching the Water Supply Line While pressing the front face of coupler (➁), insert the water line (➀) in the coupler. Reattaching the Front Leg Cover FRONT LEG COVER 25 INSTALLATION INSTRUCTIONS Carefully place front cover and push to snap it into position.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 26 ADJUSTING THE HEIGHT BETWEEN THE DOORS Please level the refrigerator first The doors will be uneven if the refrigerator is not level. Insert a flat-blade screwdriver (-) (➀) into a slot of the control lever (➁), turn it clockwise and level the refrigerator. DIFFERANCE OF HEIGHT Case 1) Freezer door is lower than the refrigerator door.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 27 ADJUSTING THE HEIGHT BETWEEN THE DOORS Making small level adjustments between doors If the freezer door is lower than the refrigerator door. If the freezer door is higher than the refrigerator door. Adjustment location Adjustment location Please open the doors and adjust the doors as follows: 1) Release the nut (①) on the lower hinge until the upper end of the bolt (➁).
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 28 CHECKING THE WATER DISPENSER LINE 1) In order to operate the ice maker properly, water pressure of 20 ~125 psi (0.138~0.862 Mpa) is required. In this range, a 100cc paper cup can be filled in 10 secs. 2) The water filter removes particles. It does not sterilize or destroy any micro-organisms. 3) If the refrigerator is installed in area with low water pressure (below 20psi), you should install a booster pump to compensate for the low pressure.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 29 INSTALLATION OF THE WATER DISPENSER LINE Before You Install the water line • This water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of expensive water damage. • Banging pipes (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 30 INSTALLATION OF THE WATER DISPENSER LINE (Case 2) Check the water supply line Connect the water pipe with coupler and tap. - Close the main water tap. - Connect coupler “A” to the tap. - Every join should be protected with sealing tape. WARRANTY INFORMATION This water line installation is not covered by the refrigerator or ice maker manufacturer's warranty. Follow these instructions carefully to minimise the risk of expensive water damage.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 31 INSTALLATION OF THE WATER DISPENSER LINE Install the water filter NOTE The water filter is located in the extra space behind the Deli Bin. - As shown, separate the fixed cap in the refrigerator by rotating it counterclockwise. Remove the water filter from the box and put a month indicator sticker on the filter as shown. - Write the month you installed the filter on the label.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 32 INSTALLATION OF THE WATER DISPENSER LINE Select the location where the purifier is to install. (Model with the purifier) LINE OUTLET - Cut the water line attached to the purifier to the appropriate place after measuring the distance between the purifier and the cold water tap. SIDE OF PURIFIER - If you wish to reassemble the water inlet and outlet sides of the purifier during purifier installation, see the reference illustration.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 33 INSTALLATION OF THE WATER DISPENSER LINE WATER TUBE Secure the purifier in position. - Fix the purifier in position, as shown in the figure PURIFIER on the right. PURIFIER LOCK STATIONS TIGHTENING BAND Connect the water line to the refrigerator. WATER LINE CONNECTION NUT - Remove the compressor cover of the refrigerator. - Connect the water line to the valve, as shown in the figure. - When connected, check if there is any leakage.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 34 INSTALLATION OF THE WATER DISPENSER LINE Check the amount of water supplied to the ice tray. 1) To remove : Set the "Ice Type" switch to the Ice off position. Lift up (①) and pull out (➁) the icemaker bucket in the freezer. To replace : When replacing the drawer, be sure to press it ICE MAKER firmly into place. If it does not go all the way back, remove it and rotate the drive mechanism 1/4 turn. Then push the drawer back again.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 35 BEFORE YOU CALL FOR SERVICE... The refrigerator does not work sufficiently or at all Possible Causes What To Do • Check that the power plug is properly connected. • Try setting it to a lower temperature. • Disconnected power plug • Is the temperature control on the display panel set to the correct temperature? • Is the refrigerator in direct sunlight or locat- • Move the refrigerator to the proper location.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 36 BEFORE YOU CALL FOR SERVICE... Problem Small or hollow cubes Slow ice cube freezing Possible Causes What To Do Water filter clogged. Door left open. Temperature control not set cold enough. Orange glow in the freezer Defrost heater is on. Cube dispenser does not work(on some models) • This is normal. Icemaker turned off or water supply turned off. Ice cubes are frozen to icemaker feeler arm. Irregular ice clumps in storage container.
DA99-00810A-0.
DA99-00810A-0.
DA99-00810A-0.
DA99-00810A-0.6(EN) 3/14/07 11:52 AM Page 40 Ambient Room Temperature Limits This fridge/freezer is designed to operate in ambient temperatures specified by its temperature class marked on the rating plate.