NETWORK CAMERA User Manual PNV-A6081R PND-A6081RV/PND-A6081RF PNO-A6081R/PNB-A6001
Network Camera User Manual Copyright ©2021 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) 7.
overview Class construction An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. Battery Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. The battery cannot be replaced. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S.
CONTENTS OVERVIEW 6 8 Important Safety Instructions Recommended PC Specifications Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs Optional Accessories for Installation OUTDOOR VANDAL DOME CAMERA 9 9 10 What’s Included At a Glance Installation INDOOR DOME CAMERA 17 17 18 What’s Included At a Glance Installation 24 24 25 What’s Included At a Glance Installation 31 31 32 What’s Included At a Glance Installation 3 9 17 FLUSH MOUNT DOME CAMERA 24 OUTDOOR BULLET CA
overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS CPU : Intel(R) Core(TM) i7 3.4 GHz or higher RAM : 8G or higher Recommended browser: Chrome Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based) Supported OS : Windows, Mac, Linux, Android, iOS, Chrome Verification environment - Windows 10: Google Chrome version 80 or later, Firefox version 72 or later, MS Edge version 83 or later - Mac 10.13/14: Safari version 11.0.
Outdoor Vandal Dome Camera Indoor Dome Camera PNV-A6081R Flush Mount Dome Camera PND-A6081RV PND-A6081RF ● OVERVIEW 9 17 Outdoor Bullet Camera PNO-A6081R 31 24 Box Camera PNB-A6001 38 English _7
overview OPTIONAL ACCESSORIES FOR INSTALLATION You can purchase appropriate optional accessories available.
AT A GLANCE outdoor vandal dome camera WHAT’S INCLUDED As for each sales country, accessories are not the same. of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection.
outdoor vandal dome camera INSTALLATION J 2. Take off the lens cover protecting the camera lens. ` This camera is waterproof and in compliance with the IP67 / IP6K9K spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. Installation (mount plate) [Directly installing on wall/ceiling] 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. ● OUTDOOR VANDAL DOME CAMERA J ` Before removing the Micro SD card, in , set the device to and press the [Apply] button and turn the camera off.
outdoor vandal dome camera [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 2-2. Separate the pipe cover of the mount plate by pressing its sides. 2-3. Place the pipe on the mount plate. 2-4. Fix the mount plate using appropriate screws. 2-5. Pull out necessary cables among network/power/audio/alarm cables through the pipe. Installation (camera case) J ` Use a cable bushing compliant with the network cable to be connected.
1-4. Mount the cable bushing to the camera case. 2-3. Mount the cable bushing to the camera case. ● OUTDOOR VANDAL DOME CAMERA [Installing the network cable] (IP66) 2-1. Pull off the extruded part of the 1-hole cable bushing provided. 2-2. Use the cap installer to pass through the RJ45 cable. [Installing audio/alarm cables] 3-1. Mount the cable bushing of the provided audio/alarm cables to the camera case.
outdoor vandal dome camera Installing the camera module 4. Join the mount plate with the camera case. 1. Connect the network/power/audio/alarm cables to the camera module terminal. 2. Attach the camera module to the case. J 2x ` A magnet is embedded at the bottom of the module ` Take caution not to allow any foreign objects between the attaching surfaces. x4 TR20 3. Adjust the lens to the desired direction with reference to “Adjusting the monitoring direction for the camera” section.
Assembling the dome cover [Using Weather cap] 1. Remove the screws from the dome cover. [Directly installing on wall/ceiling] 1. Assemble the dome cover. 2x ` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 4x ● OUTDOOR VANDAL DOME CAMERA J TR20 x4 TR20 2. Assemble the dome cover. 3. Mount the weather cap to the dome cover and fasten the screws. J J ` Make sure to firmly tighten the fastening screws so that there is no water damage issue.
outdoor vandal dome camera Outdoor installation When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 1. Connect the power, I/O, and network cables. 2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.
indoor dome camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. a Pipe-cover Mount-plate c ● INDOOR DOME CAMERA b Camera-case d Camera-module e Dome-cover of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection.
indoor dome camera INSTALLATION J 2. Take off the lens cover protecting the camera lens. ` This camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. Installation (mount plate) [Directly installing on wall/ceiling] 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. ● INDOOR DOME CAMERA J ` Before removing the Micro SD card, in , set the device to and press the [Apply] button and turn the camera off.
indoor dome camera [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 2-2. Separate the pipe cover of the mount plate by pressing its sides. 2-3. Place the pipe on the mount plate. 2-4. Fix the mount plate using appropriate screws. 2-5. Pull out necessary cables among network/power/audio/alarm cables through the pipe. Installation (camera case) J ` Use a cable bushing compliant with the network cable to be connected.
1-4. Mount the cable bushing to the camera case. 2-3. Mount the cable bushing to the camera case. ● INDOOR DOME CAMERA [Installing the network cable] 2-1. Pull off the extruded part of the 1-hole cable bushing provided. 2-2. Use the cap installer to pass through the RJ45 cable.
indoor dome camera [Installing audio/alarm cables] 3-1. Mount the cable bushing of the provided audio/alarm cables to the camera case. Installing the camera module 1. Connect the network/power/audio/alarm cables to the camera module terminal. 2. Attach the camera module to the case. J ` A magnet is embedded at the bottom of the module ` Take caution not to allow any foreign objects between the attaching surfaces. 3. Connect the microphone cable to the camera module. 4.
Assembling the dome cover J [Directly installing on wall/ceiling] ` Be careful not to alter the monitoring direction of your camera. 1. Assemble the dome cover. ● INDOOR DOME CAMERA J ` Make sure to firmly tighten the fastening screws so that there is no water damage issue.
flush mount dome camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. a Bracket b Housing c Camera-module of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power f IR LED g Illumination Sensor i Reset button Network h of the Be ware CAUTION: and Polarity Rated Voltageconnection.
INSTALLATION J 2. Take off the lens cover protecting the camera lens. ` This camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
flush mount dome camera Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot. J ` Before removing the Micro SD card, in , set the device to and press the [Apply] button and turn the camera off. ` If you turn off the camera or remove the Micro SD card that contains data from the product, the data may be lost or damaged. Installation (housing) 1.
3. Connect the safety cable. J ` A safety cable is not provided. 4-2. Pull out necessary cables among network/power/audio/alarm cables through the pipe. ● FLUSH MOUNT DOME CAMERA e.g. [Using pipe] 4-1. Install the pipe in a fitting hole.
flush mount dome camera Installation (camera case) J ` Use a cable bushing compliant with the network cable to be connected. - Components: use a cable with the diameter of Ø5 to 8.5 [Installing network/power cables] [Installing the network cable] 2-1. Pull off the extruded part of the 1-hole cable bushing provided. 2-2. Use the cap installer to pass through the RJ45 cable. Cap Installer 1-1. Pull off the extruded parts of the cable bushing to be used. 1-2.
[Installing audio/alarm cables] 3-1. Mount the cable bushing of the provided audio/alarm cables to the camera case. Installing the camera module 1. Connect the network/power/audio/alarm cables to the camera module terminal. 2. Attach the camera module to the case. ` A magnet is embedded at the bottom of the module ● FLUSH MOUNT DOME CAMERA J ` Take caution not to allow any foreign objects between the attaching surfaces. 4. Turn the screws on the housing to fix the housing to the ceiling.
flush mount dome camera Assembling the dome cover Waterproofing cables 1. Assemble the dome cover. J ` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 4x If there is any possibility of moisture intrusion through the gap of the cable, please waterproof the concerned area with waterproof butyl rubber tape (can be purchased in stores) as below. 1. Connect the power, I/O, and network cables. 2.
outdoor bullet camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. Pipe-cover b Mount plate d c e Bottom cover f Sunshield Camera body i Reset button of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power f Network port Sunshield fixing screw of the Be ware CAUTION: and Polarity Rated Voltageconnection.
outdoor bullet camera INSTALLATION J ` This camera is waterproof and in compliance with the IP67 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD card from the slot.
Installation (Mount plate) [Directly installing on wall/ceiling] [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. ● OUTDOOR BULLET CAMERA 2-2. Separate the pipe cover of the Mount plate by pressing its sides. 1-2. Fix the Mount plate using appropriate screws. 1-3.
outdoor bullet camera 2-3. Place the pipe on the Mount plate. 2-4. Fix the Mount plate using appropriate screws. 1-4. Mount the cable bushing to the Bottom cover. 2-5. Pull out necessary cables among network/power/audio/alarm cables through the pipe. Installation (Bottom cover) J ` Use a cable bushing compliant with the network cable to be connected. - Camera main: use a cable with the diameter of Ø5 to 6.5 - Components: use a cable with the diameter of Ø5 to 8.
2-3. Mount the cable bushing to the Bottom cover. 4. Join the Mount plate with the Bottom cover. ● OUTDOOR BULLET CAMERA 3x HEX x4 S3 [Installing audio/alarm cables] 3-1. Mount the cable bushing of the provided audio/alarm cables to the Bottom cover.
outdoor bullet camera Installing the camera module 1. Hang the safety cable up on a hook that looks like an arrow in the Bottom cover. 3. Attach the camera body to the Bottom cover. J ` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 3x x4 HEX S3 e.g. 4. Adjust the camera direction using the Hex. L wrench provided. 2. Connect the network/power/audio/alarm cables to the camera module terminal.
5. Assemble the sunshield to the camera body using sunshield fixing screw. Outdoor installation When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside. 2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.
box camera WHAT’S INCLUDED AT A GLANCE As for each sales country, accessories are not the same. b Mounting Bracket Screw Hole a CS mount Lens (not included) c Auto Iris Lens port l Test monitor out port k Audio cable port d Micro SD card Compartment e GND Option (not included) of the Be ware CAUTION: and Polarity Rated Voltageconnection.
MOUNTING THE LENS Disconnect the power before proceeding. ` The CS mount Lens are not included in the product package. It is recommended that megapixel lens are use on this camera to optimise performance. Focusing Select a target to film, turn the zoom lever of the lens to adjust the magnification and then focus the lens so that target is clearly displayed. Mounting the CS mount Lens on a camera Turn the CS mount Lens clockwise to attach it.
box camera INSERTING/REMOVING A MICRO SD CARD Inserting a Micro SD card Insert a Micro SD card in the arrow direction shown in the figure. J ` Before installing the camera, the Micro SD card should be inserted while the power source and the body are separated. ` Do not forcefully insert it in the reverse direction. It might damage your Micro SD card and your product. ` When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.
installation & connection ADJUSTING THE MONITORING DIRECTION FOR THE CAMERA J ` Adjust the direction of IR LEDs not to hinder their view by an instrument. J ` Adjust the direction of IR LEDs not to hinder their view by a weather cap (if any). ● INSTALLATION & CONNECTION Tilt Pan Lens rotation ` Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling.
installation & connection CONNECTING WITH OTHER DEVICE SOFT AP WiFi dongle WiFi dongle Monitor for installation AUDIO OUT RESET VIDEO AUDIO IN USB FOCUS NETWORK Grounding cable 1234567 1 : ALARM 1 5 : GND 2 : ALARM 2 6 : RS-485+ 3 : GND 7 : RS-4854 : ALARM OUT PoE+ DC 12V (12V 50mA) Ethernet Power Power Monitor for installation Ethernet Monitor for installation J Ethernet Power SOFT AP 42_ installation & connection WiFi dongle <
Ethernet Connection Connect the Ethernet cable to the local network or to the Internet. Connecting WiFi 1. Connect OTG adapter (5-pin) and WiFi dongle to the micro USB port. Smartphone Setup 2. Select the camera SSID after turning on the WiFi. 3. Run the Wisenet Installation application. 4. When you log in to the camera, the video will be connected. ` The video will be played without being logged in during the initial connection. 5.
installation & connection Connecting to Audio Input/Output Microphone AUDIO OUT RESET VIDEO • Audio Codec - Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.
Connecting to the I/O port box Connect the Alarm I/O cable to the corresponding port of the port box. Connecting to the I/O port box(PNB-A9001) Connect the Alarm I/O cable to the corresponding port of the port box.
installation & connection Alarm In Wiring Diagram External connection Inside of the camera VCC_3.3V RESISTOR Sensor ALARM #1(5 mA SINK) RESISTOR RESISTOR DIODE TRANSISTOR MLCC GND GND To connect the alarm out If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open collector method, it may cause malfunction.
network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM 1. Launch an Internet browser on the local PC. DSL/Cable Modem 2. Enter the IP address of the camera in the address bar of the browser. INTERNET External Remote PC Camera DDNS Server (Data Center, KOREA) Camera 1. Connect the user PC directly with the network camera.
network connection and setup USING DEVICE MANAGER M ` Device manager program can be downloaded from - menu at Hanwha Techwin website (http://www.hanwha-security.com). ` More instructions of Device Manager can be found at menu of the main page. AUTOMATICALLY SEARCHING CAMERA If a camera is connected to the same network of the PC where device manager is installed, you can find network camera by using search function. 1.
Configuring Dynamic IP Receive IP address from DHCP - If connecting the camera directly to modem using the DHCP protocols - If IPs are assigned by the internal DHCP server via the LAN 1. Click the camera from the list that you want to change the IP setting. 1. Click the camera from the list that you want to automatically configure the IP. PNO-A6081R 2. Click < + > at the main page of device manager. • Equipment Setting menu appears.
network connection and setup PORT RANGE FORWARD (PORT MAPPING) SETUP If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. Manual Port Range Forwarding Setting up Port Range Forward for several network cameras • You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. • A user can change each port using the camera setting screen.
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. M ● NETWORK CONNECTION AND SETUP 2. Double-click a camera to access. The Internet browser starts and connects to the camera. ` Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
web viewer CONNECTING TO THE CAMERA Normally, you would 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2.
PASSWORD SETTING When you access the product for the first time, you must register the login password. ` For a new password with 8 to 9 digits, you must use at least 3 of the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. - Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/ 1. Click the [Setup ( )] icon. 2. The Settings window appears. 3.
appendix TROUBLESHOOTING PROBLEM When an Windows 10 user accesses the web viewer through Chrome or Firefox, the sound volume of microphone changes periodically. What are the specifications for WAVE files necessary to play audio at the time of an event? No video is displayed when accessing the plug-in free webviewer on Safari via HTTPS. SOLUTION y This is what happens when microphone driver has been set to Realtek driver.
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
