Range Hood Hotte de la cuisine Campana de cocina Installation Instructions Guide Guide d’instructions d’installation Guía de Instrucciones para Instalación NK30K7000WS / NK36K7000WS / NK30K7000WG / NK36K7000WG LIB0124068
Table of Contents Table of Contents 2 Important Safety Instructions 3 Installation Requirements 4 Electrical Requirements Venting Requirements Venting Methods Tools and Parts Dimensions and Clearances 4 4 4 5 5 Installation 6 Prepare Location Vent Cover Bracket Installation Installing the Range Hood Connect Vent System Electrical Connection Install Duct Covers Complete Installation 6 6 6 7 7 8 8 Range Hood Use 8 Range Hood Controls Range Hood Description Conectivity Cooktop / Hood Range 9 8
Important Safety Instructions APPROVED FOR RESIDENTIAL APPLIANCES FOR RESIDENTIAL USE ONLY READ AND SAVE THESE INSTRUCTIONS PLEASE READ ENTIRE INSTALLATION GUIDE BEFORE PROCEEDING. INSTALLATION MUST COMPLY WITH ALL LOCAL CODES. IMPORTANT: Important Safety Instructions Save these Instructions for the Local Electrical Inspector’s use. INSTALLER: Please leave these Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference.
Important Safety Instructions WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING PRECAUTIONS: ■■ Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. ■■ Before servicing or cleaning the unit, switch the power off at the service panel and lock the service panel to prevent power from being switched on accidentally.
Installation Requirements For the most efficient and quiet operation: IMPORTANT Observe all governing codes and ordinances. •• Use no more than three 90° elbows. •• It is the customer’s responsibility: To contact a qualified electrical installer. To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.
Installation Requirements Tools and Parts Dimensions and Clearances E Parts supplied Removing the packaging CAUTION! Remove carton carefully, wear gloves to protect against sharp edges. G F Installation Requirements WARNING Remove the protective film covering the product before putting into operation. •• Hood canopy assembly with blower and LED lamps already installed. C •• 6” (15.2 cm) round air transition D •• Duct covers •• Hardware bag with: Part 5x45 mm Qty Part Qty 6 5.
Installation Installation Instructions Vent cover bracket installation 1. Attach the vent cover bracket to the wall flush to the ceiling using 2 - 5 x 45 mm screws. Prepare Location •• It is recommended that the vent system be installed before the hood is installed. •• Before making cutouts, make sure there is proper clearance within the ceiling or wall for the exhaust vent. •• Check your ceiling height and the hood height maximum before you select your hood. A D B 1. Disconnect power. A.
Installation Connecting Vent System 1. Install the transition on the top of the hood (if removed for shipping) with 2 - 3.5 x 9.5 mm sheet metal screws. B C A A Installation B A. Terminal box B. Knockout C. Terminal box cover 4. Run the home power supply cable through strain relief, into terminal box. A. Vent transition B. 3.5 x 9.5 mm screw A B For vented installations only: 2. Fit the vent system over the exhaust outlet. E 3.
Installation Installing the duct covers Secure the bottom of the duct with 2 - 4.2 x 8 mm screws. When using both upper and lower vent covers, push the lower cover down onto hood and lift the upper cover to the ceiling and install with two mounting screws. NOTE For vented installations, the upper vent cover may be reversed to hide the slots. C D C A Installation Completing the Installation B 1. Install the metal baffle filters. See the “Range Hood Care” section. 2.
Range Hood Use Range Hood Controls A B C D E F G I A. Power B. Low Speed C. Medium Speed D. High Speed E. Boost Speed F. Timer Display G. Timer H. Light I. Auto Connectivity J. Bluetooth CONNECTIVITY COOKTOP / HOOD RANGE •• This appliance has a feature which allows you to pair compatible Samsung cooktops and your hood via Bluetooth. •• Press the POWER button and the hood will be activated at default speed (Default Speed : Low).
Range Hood Care Range Hood Care 2. Wash the stainless steel baffle filter as needed in your dishwasher or a hot detergent solution. Cleaning 3. Reinstall the filter by making sure the spring release handles are toward the front. Insert the stainless steel filter into the upper track. IMPORTANT: Clean the hood and baffle filters frequently according to the following instructions. Replace the baffle filters before operating the hood.
warranty (USA) SAMSUNG RANGE HOOD Limited warranty to original purchaser This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc.
warranty (Canada) SAMSUNG RANGE HOOD Limited warranty to original purchaser This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc.