User Manual C49J890DK* The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. The contents of this manual are subject to change without notice to improve quality. © Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Table of contents Before Using the Product Securing the Installation Space Precautions for storage 4 4 Safety Precautions Cleaning Electricity and Safety Installation Operation 4 5 5 6 7 Preparations Parts 9 Control Panel 9 Direct Key guide 10 Function Key Guide 11 Changing Brightness, Contrast and Eye Saver Mode settings 13 Changing the Volume setting 13 Types of Ports 14 Upgrading the Software via USB 15 Adjusting the Product Tilt and Height 17 Anti-theft Lock 18 Connecting and Using a Source Device
Table of contents PIP/PBP System Troubleshooting Guide PIP/PBP Mode 34 USB Source Setup 41 Size 35 DisplayPort Ver.
Chapter 01 Before Using the Product Securing the Installation Space Safety Precautions Ensure some space around the product for ventilation. An internal temperature rise may cause fire and damage the product. Be sure to allow the amount of space as shown below or greater when installing the product. ――The exterior may differ depending on the product. A serious or fatal injury may result if instructions are not followed.
Cleaning ――Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. ――Take the following steps when cleaning. 1 2 •• Do not use a damaged power cord or plug, or a loose power socket. Disconnect the power cord from the product. •• Do not use multiple products with a single power socket. ――Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric Wipe the monitor with a clean, soft and dry cloth.
Installation Warning Caution •• DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES. •• Do not drop the product while moving. •• Do not install the product in poorly ventilated spaces such as a bookcase or closet. •• Install the product at least 10 cm away from the wall to allow ventilation. •• Keep the plastic packaging out of the reach of children. ‒‒ Children may suffocate.
Operation Warning •• There is a high voltage inside the product. Never disassemble, repair or modify the product yourself. ‒‒ Contact Samsung Customer Service Center for repairs. •• To move the product, first disconnect all the cables from it, including the power cable. •• If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord immediately and contact Samsung Customer Service Center.
Caution •• Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels. ‒‒ Activate power-saving mode or a moving-picture screen saver if you will not be using the product for an extended period of time. •• Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time (vacation, etc). ‒‒ Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.
Chapter 02 Preparations Parts Icons Description Source Control Panel PBP/PIP Switch USB •• Shortcut Key for Switching to a Source ――The color and shape of parts may differ from what is shown. Specifications are subject to change without This button is a shortcut for switching to a different source. notice to improve quality. ‒‒ When the source is switched, the USB connection will be changed at the same time according to the settings of USB Source Setup.
Icons Description This LED is power status indicator and works as •• Power On (Power button): Off Power LED •• Power saving mode: Blinking Direct Key guide ――The shortcut button screen (OSD menu) shown below is displayed only when the monitor screen is turned on, the computer resolution changes, or the input source changes. ――The function buttons page shows if Eye Saver Mode is enabled. •• Power Off (Power button): On : On ――The power Indicator operation can be swapped by changing in the menu.
Function Key Guide ――To enter the main menu or to use other items, press the JOG button to display the Function Key Guide. You can exit by pressing the JOG button again. UP/DOWN/LEFT/RIGHT: Move to the item you want. The description for each item will appear when the focus changes. PRESS(ENTER): The selected item will be applied. Return Icons Description Selects to change the input signal by moving the JOG button in the Function Key Guide screen.
When the monitor displays nothing (i.e. Power saving mode or Non-signal mode), 2 direct keys for control source and power could be used as below. JOG Button Power saving/Non-signal mode UP Source Change Down PRESS(ENTER) for 2 seconds Power Off When the monitor displays the Main menu the JOG Button could be used as below. JOG Button Action UP/DOWN Move the option Exit the Main menu. LEFT Close Sublist without saving value. Value decreases in the slider. RIGHT PRESS(ENTER) Move to next depth.
Changing Brightness, Contrast and Eye Saver Mode settings You can adjust Brightness, Contrast or Eye Saver Mode by moving the JOG button up or down, if no OSD menu is displayed. Changing the Volume setting You can adjust Volume by moving the JOG button left or right, if no OSD menu is displayed. 50 Volume Mute Contrast Off Eye Saver Mode ――The displayed image may differ depending on the model.
Types of Ports ――The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. POWER IN Port Description Connect the power cord for your monitor to the POWER IN port on the back of the product. POWER IN Connects to a source device using an HDMI cable or HDMI-DVI cable. Connects to a PC using a DP cable. Port Description Connect to a USB device.
Upgrading the Software via USB 1 2 Be sure to insert the USB disk into the USB port marked out with the blue box as shown in the figure below. You can upgrade the software via USB only if either the monitor screen operates When the message as shown in the following figure is displayed on the monitor, select Yes to upgrade the software. Do you want to update via USB? normally or the check signal is displayed on the monitor screen.
Note 1 2 3 Before upgrading through USB disk, you need to format the USB disk into the FAT32 format. Make sure only the BIN file for upgrade is in the USB disk. For the CJ89 model, make sure each upgrade file is in the BIN formate and follow the naming rules of CJ89 (m-J89**CGAA-****.*[4-digit number].bin), wherein ** indicates the monitor size in inches, ****.* stands for the version number and the 4-digit number is the checksum. For example, “m-J8949CGAA-1000.0[9A80].
Adjusting the Product Tilt and Height Caution ――The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. -2.0° (±2.0°) ~ 15.0° (±2.0°) -15.0° (±2.0°) to Left ~ 15.0° (±2.0°) to Right •• Grasp the left and right sides of the monitor and adjust the tilt. After adjusting the product tilt and height, if the screen is not level, take the following actions. 0 ~ 120.0 mm (±5.
Anti-theft Lock ――An anti-theft lock allows you to use the product securely even in public places. ――The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details. To lock an anti-theft locking device: 1 2 3 4 Fix the cable of your anti-theft locking device to a heavy object such as a desk. Put one end of the cable through the loop on the other end.
Installation Attaching the Stand (Type one) ――Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. : The product is curved. Placing pressure on the product when on a flat surface may damage the product. When the product is on the ground facing up or down, do not put pressure on it. 1 Caution Hold the stand neck with both hands, not one hand, to prevent it from falling off and causing injury.
Attaching the Stand (Type two) ――Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. : The product is curved. Placing pressure on the product when on a flat surface may damage the product. When the product is on the ground facing up or down, do not put pressure on it. 1 Caution Hold the stand neck with both hands, not one hand, to prevent it from falling off and causing injury.
Removing the Stand (For Attaching the BRACKET WALL) ――Before removing the stand from the monitor, place the monitor on a flat and stable surface with the screen facing down. : The product is curved. Placing pressure on the product when on a flat surface may damage the product. When the product is on the ground facing up or down, do not put pressure on it. 1 Rotate the COVER-REAR TOP counterclockwise. 5 Unfasten the 4 screws at the top of the stand neck. 2 Lift the COVER-REAR TOP.
Attaching the BRACKET WALL ――Power the product off and remove the power cable from the power socket. 1 2 •• Notes ‒‒ Using a screw longer than the standard length can damage the internal components of the product. ‒‒ The length of screws required for a wall mount that does not comply with the VESA standards may vary depending on the specifications. ‒‒ Do not use screws that do not comply with the VESA standards. Do not attach the wall-mount kit or desktop stand using excessive force.
Chapter 03 Connecting and Using a Source Device Read below before installing the monitor. Connecting and Using a Source Device 1 Check the shapes of both ends of the cables that came with the monitor, and check the shapes and Select a connection method suitable for your source device. positions of the matching ports on the monitor and external devices. ――Connecting parts may differ in different products.
Connection Using the DP Cable Connection Using the USB Type-C Cable Check to make sure that the power cables for the monitor and external devices, such as computers and set-top boxes, are not connected to the power outlet. Check to make sure that the power cables for the monitor and external devices, such as computers and set-top boxes, are not connected to the power outlet. ――When connecting a DP cable, use the cable that came with the components of the monitor.
Connecting to Headphones Connecting the Product to a Source Device as a USB Hub Connecting a Source Device to the Product ――The product can function as a USB hub when it is connected to a source device via a USB Type-C cable or USB Type-C to A cable. Then you can connect USB devices to the product without having to directly connect them to the source device, and then you can control the USB devices from the product.
Utilizing the Product as a USB HUB Using the product as a hub, connect and use various source devices with the product at the same time. A source device cannot connect to multiple devices at the same time if it has a limited number of available input/output ports. In this case, the hub feature of the product will improve your work efficiency by allowing you to connect multiple devices to the USB ports on the product at the same time without directly connecting them to a source device.
Connecting the Power POWER IN To use the product, connect the power cable to a power outlet and the POWER IN port on the product. ――The input voltage is switched automatically.
Tidying Up the Connected Cables : Headphones hanger : Downward : Upward 1 Connect the corresponding cables. 6 2 Arrange the cables against the bend tendency of the cables and pull the cables out of the COVER-REAR SUB grooves. 7 Attach the COVER STAND BODY REAR in Move down the COVER STAND BODY the direction as shown in the figure with REAR until it covers the stand neck the buckles not being exposed. completely.
Correct posture to use the product Driver Installation ――You can set the optimum resolution and frequency for this product by installing the corresponding drivers. ――To install the latest version of the product driver, download it from the Samsung Electronics website at http://www.samsung.com. Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase.
Chapter 04 Picture A detailed description of each function is provided. Refer to your product for details. ――The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. In PC mode •• Custom: Customize the contrast and brightness as required. •• Standard: Obtain a picture quality suitable for editing documents or using Internet.
Brightness Color You can adjust the general brightness of the picture. (Range: 0~100) Adjust the tint of the screen. A higher value will make the picture appear brighter. ――This menu is not available when SAMSUNG Bright is set to Cinema mode. ――This menu is not available when Smart ECO Saving is enabled. ――This menu is not available when Eye Saver Mode is enabled. ――This menu is not available when Eye Saver Mode is enabled. ――Not available when PIP/PBP Mode is set to On.
SAMSUNG MAGIC Upscale Eye Saver Mode MAGICUpscale function Set to an optimum picture quality suitable for eye relaxation. SAMSUNG can enhance the layers of the picture details and the vividness of the picture. The function has more obvious effects on low-resolution pictures. ――This menu is not available when SAMSUNG Bright is set to Cinema mode. MAGIC ――Not available when PIP/PBP Mode is set to On. •• Off / Mode1 / Mode2 ――Comparing with Mode1, Mode2 has a stronger effect.
Picture Size Screen Adjustment Change the picture size. ――This menu is only available when Picture Size is set to Screen Fit in AV Mode. ――This menu is not available when PIP/PBP Mode is set to On and the Size is set to (PBP Mode). In PC mode •• Auto: Display the picture according to the aspect ratio of the input source. •• Wide: Display the picture in full screen regardless of the aspect ratio of the input source.
Chapter 05 PIP/PBP A detailed description of each function is provided. Refer to your product for details. ――The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. PIP/PBP Mode ――PIP/PBP mode is compatible with Windows 7, Windows 8, and Windows 10. ――The PIP/PBP function may not be available depending on the specifications of the graphics card used.
Size Position Select the size and aspect ratio of the sub-screen. Select the position of the sub-screen from the available options. •• : Select the icon image if you want to use PBP mode where the optimum resolution for the left and right sides of the screen is 1920 x 1080 (width x height). •• •• : Select the icon image if you want to use PIP mode where the optimum resolution for the subscreen is 720 x 480 (width x height).
Source Select the source for each screen. PIP Mode (available in PIP mode(Size / )) ――The input source for the main screen changes. ――With the exception of the current input source, the other two input sources can be selected. ――The screen may flicker if the input signal is unstable. ――When the Function Key Guide appears, move the JOG button LEFT to select the icon and then press the JOG button. The main screen will switch in the order HDMI → DisplayPort → USB Type-C 1 → USB Type-C 2.
Switch USB PC Mobile Phone HDMI Cable HDMI IN Monitor DP Cable PC Screen DP IN USB Type-C Cable Laptop/Mobile Phone Screen USB Cable Laptop USB Type-C Cable The KVM (keyboard, video, and mouse) switch enables users to use only a keyboard, a video monitor, and a mouse for controlling multiple input sources. The function of the Samsung USB switch is as follows: •• When PIP/PBP of a Samsung monitor is on, USB devices (I/O device, USB storage device, etc.
Picture Size PBP Mode (available in PBP mode(Size )) Set the Picture Size for each of the divided screens. PIP Mode (available in PIP mode (Size / )) Select the image size for sub-screen. In PC mode In PC mode •• Auto: Display the picture according to the aspect ratio of the each screen input source. •• Wide: Display the picture in full screen regardless of the aspect ratio of the each screen input source. •• Auto: Display the picture according to the aspect ratio of the each screen input source.
Contrast PIP Mode (available in PIP mode(Size / )) Adjust the contrast level for sub-screen. PBP Mode (available in PBP mode(Size )) Adjust the contrast level for each screen.
Chapter 06 OnScreen Display A detailed description of each function is provided. Refer to your product for details. ――The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Position Adjust the menu position. Transparency Set the transparency for the menu windows. Language Set the menu language.
Chapter 07 System A detailed description of each function is provided. Refer to your product for details. ――The functions available may vary depending on the product model. The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. DisplayPort Ver. Select your DisplayPort version. USB Source Setup This option is for assigning correct USB ports for HDMI and DP ports.
Smart ECO Saving PC/AV Mode The Smart ECO Saving function reduces power consumption by controlling the electric current used by the monitor panel. Set PC/AV Mode to AV. The picture size will be enlarged. ――This menu is not available when Eye Saver Mode is enabled. •• Off: Deactivate the Smart ECO Saving function. •• On: The power consumption will automatically be reduced by about 10 % over the current setting. (The reduction of power consumption depends on the customer screen brightness condition.
Source Detection Information Select either Auto or Manual as the method to recognize input signal. View the current input source, frequency, software version, and resolution. Key Repeat Time Control the response rate of a button when the button is pressed. Acceleration, 1 sec, or 2 sec can be selected. If No Repeat is selected, a command responds only once when a button is pressed. Power LED On Configure the settings to enable or disable the power LED located at the lower part of the product.
Chapter 08 Installing the Software Easy Setting Box System Requirements OS Easy Setting Box enables users to use the monitor by partitioning multiple sections. To install the latest version of Easy Setting Box, download it from the Samsung Electronics website at http://www.samsung.com. Hardware •• Windows 7 32Bit/64Bit •• At least 32MB of memory •• Windows 8 32Bit/64Bit •• At least 60MB of free space on the hard disk drive •• Windows 8.
Chapter 09 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center ――Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center. Check the following. Installation issue (PC mode) The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connectors are locked.
Not Optimum Mode is displayed. Video playback is choppy. This message appears when the signal from the graphics card exceeds the maximum resolution or frequency for the product. Playback of high-definition large video files can be choppy. This may be because the video player is not optimized for the computer resource. Change the maximum resolution and frequency to suit the product performance, referring to Standard Signal Mode Table (P.50). Try playing the file on another video player.
Universal Serial Bus (USB) issue USB interface is not working (USB devices are not working). Check that your monitor is turned on. Reconnect the USB cable to your computer. Reconnect the USB devices (USB connectors). Turn off and then turn on the monitor again. Reboot the computer. Some USB devices like external portable HDDs require a higher electric current. Then connect the devices directly to the computer. The USB Type-C port does not supply power (USB devices are not charged).
Q&A ――Refer to the user manual for your PC or graphics card for further instructions on adjustment. How can I change the frequency? Set the frequency on your graphics card. •• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Screen Resolution → Advanced settings → Monitor, and adjust Refresh rate under Monitor settings. •• Windows 8(Windows 8.
Chapter 10 Specifications General Model Name C49J890DK* Size 49 Class (48.9 Inches / 124.2 cm) Display area 1195.8 mm (H) x 336.3 mm (V) 47.1 Inches (H) x 13.2 Inches (V) Pixel Pitch 0.3114 mm (H) x 0.3114 mm (V) 0.01226 Inches (H) x 0.01226 Inches (V) Maximum Pixel Clock 660 MHz Power Supply AC100-240V~ 50/60Hz Refer to the label at the back of the product as the standard voltage can vary in different countries.
Standard Signal Mode Table Synchronization Resolution Horizontal Frequency 30 – 170 kHz Vertical Frequency 50 – 144 Hz Optimum Resolution 3840 x 1080 @ 60 Hz Maximum Resolution 3840 x 1080 @ 120 Hz (HDMI) 3840 x 1080 @ 144 Hz (DisplayPort) 3840 x 1080 @ 144 Hz (USB Type-C) If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will automatically be adjusted.
Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 1280 x 1024 79.976 75.025 135.000 +/+ VESA, 1440 x 900 55.935 59.887 106.500 -/+ VESA, 1600 x 900 60.000 60.000 108.000 +/+ VESA, 1680 x 1050 65.290 59.954 146.250 -/+ VESA, 1920 x 1080 67.500 60.000 148.500 +/+ VESA, 3840 x 1080 66.625 59.968 266.500 +/- VESA, 3840 x 1080 113.250 99.956 453.000 +/- VESA, 3840 x 1080 137.250 119.974 549.
Chapter 11 Appendix Responsibility for the Pay Service (Cost to Customers) A Product damage caused by customer's fault ――When the service is requested, in spite of in warranty, we may charge you for a visit from a service •• External impact or drop. technician in the following cases. Not a product defect Cleaning of the product, Adjustment, Explanation, Re-installation and etc. •• If a service technician gives instructions on how to use product or simply adjusts options without disassembling product.
Extended warranty You can buy an extended warranty within 90 days of purchasing the product. The extended warranty will cover an additional period of 3 years, beyond the standard 3 year warranty. Samsung guarantee that replacement parts will be available for 5 years after the end of production. After 5 years, in the event that the Samsung’s service center has run out of replacement parts and cannot repair the product, Samsung will replace your product at no additional charge.