FULL MANUAL HW-C400 Imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.com/register Para evitar cualquier avería o daños, lea detalladamente este manual de instrucciones antes de conectar y utilizar este aparato. Conserve el manual para referencia futura.
SAFETY INFORMATION SAFETY WARNINGS WARNING •• To reduce the risk of fire or electric shock, do TO REDUCE THE RISK OF ELECTRIC SHOCK, DO not expose this appliance to rain or moisture. NOT REMOVE THE COVER (OR BACK). CAUTION NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Refer to the table below for an explanation of symbols which may be on your Samsung product. CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. This symbol indicates that high voltage is present inside.
PRECAUTIONS 5. The battery used with this product contains chemicals that are harmful to the environment. Do not dispose of the battery 1. Ensure that the AC power supply in your in the general household trash. Do not house complies with the power expose the battery to excess heat, direct requirements listed on the identification sunlight, or fire. Do not short circuit, sticker located on the bottom of your product.
CONTENTS 01 Checking the Components 6 02 Product Overview 7 03 04 Top Panel of the Soundbar -------------------------- 7 Bottom Panel of the Soundbar -------------------------- 8 Using the Remote Control Inserting Batteries before using the Remote Control (AAA batteries X 2) -------------------------- 9 How to Use the Remote Control -------------------------- 9 Using the Hidden Buttons (Buttons with more than one function) -------------------------- 14 Output specifications for the diff
08 Connecting a USB Storage Device 21 09 Connecting a Mobile Device 23 10 11 Connecting via Bluetooth -------------------------- 23 Connecting a Soundbar to a mobile device via NFC function -------------------------- 26 Installing the Wall Mount (Optional) 27 Installation Precautions -------------------------- 27 Wall mount Components -------------------------- 27 Software Update 30 Reset -------------------------- 31 12 Troubleshooting 32 13 License 33 14 Open Source License No
01 CHECKING THE COMPONENTS SOUND MODE WOOFER CH LEVEL Soundbar Main Unit Power Cord (Soundbar) TONE CONTROL Remote Control / Batteries (Not available in some locations or models) •• For more information about the power supply and power consumption, refer to the label attached to the product. (Label: Bottom of the Soundbar Main Unit) •• To purchase additional components or optional cables, contact a Samsung Service Center or Samsung Customer Care.
02 PRODUCT OVERVIEW Top Panel of the Soundbar Top Panel NFC The LED Indicator flashes, glows, or changes color depending on the Soundbar's current mode or status. The color of the LED indicator and the number of lights indicate the active mode as described below. LED indicator W W M W W White LED White LED Multicolor LED White LED White LED •• The Multicolor LED changes to White, Cyan, Green, Red, Yellow, Orange, Purple and Blue depending on the mode or status.
NFC Logo You can activate your Bluetooth connection by placing your phone in the NFC detection area of the Soundbar. •• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds. •• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound. •• If you hear sounds from both the TV and Soundbar, go to the Settings menu for the TV audio and change the TV speaker to External Speaker.
03 USING THE REMOTE CONTROL Inserting Batteries before using the Remote Control (AAA batteries X 2) Slide the back cover in the direction of the arrow until it is completely removed. Insert 2 AAA batteries (1.5V) so that their orientation is correct. Slide the back cover back into position. How to Use the Remote Control LED Power Turns the Soundbar on and off.
Volume Push the button up or down to adjust the volume. White moves to right X1 White moves to left X1 Volume Up Volume Down LED Indicator CH LEVEL By pressing the button, you can adjust the volume of the each speaker. LED White Blinks X1 Indicator “Center Level” (Sound Control) By pressing the button, you can set the audio function. The desired item can be adjusted using the Up/ Down buttons. Each time the mode changes, the Multicolor LED blinks in white.
7 Band EQ Press and hold the (Sound Control) button for about 5 seconds to adjust the sound for each frequency band. 150Hz, 300Hz, 600Hz, 1.2kHz, 2.5kHz, 5kHz, and 10kHz are selectable using the Left/Right buttons and each can be adjusted to a setting between -6 to +6 using the Up/Down buttons. (Make sure the Sound mode is set to "Standard".) 7 Band EQ 5 Sec Press and hold the (Sound Control) button for about 5 seconds. Using the Left/Right buttos and each can be adjusted to setting between -6 to+6.
SOUND MODE By pressing the button, you can select the desired audio mode. Each time the mode changes, the Multicolor LED blinks in white. (The sound mode may differ with the TV model.) White Blinks X1 LED Indicator “Surround Sound” “Standard” –– Surround Sound Provides a wider sound field than standard. –– Standard Outputs the original sound.
FE R W OO CH LE VE L CO TO NT NE RO L FE R CO TO NT NE RO L W OO CH LE VE L CO TO NT NE RO L CH LE VE L W OO FE R DE SO M UN OD D E WOOFER (BASS) LEVEL SO M UN OD D E Push the button up or down to adjust the bass level between -6 to +6. To set the woofer (bass) volume level to 0 (Default), press the button. (Subwoofer is not included.) TONE CONTROL By pressing the button, you can adjust the volume of the treble or bass sound. The desired item can be adjusted using the Up/Down buttons.
Using the Hidden Buttons (Buttons with more than one function) Hidden Button Reference page Remote Control Button Function WOOFER (Up) TV remote control On/Off page 15 Left TV Auto connect On/Off page 19 7 Band EQ page 11 DRC On/Off page 12 Bluetooth Power On/Off page 12 (Sound Control) SOUND MODE Output specifications for the different sound effect modes Effect Surround Sound Standard Input Output 2.0 ch 2.0 ch 5.1 ch 2.0 ch 2.0 ch 2.0 ch 5.1 ch 2.
Adjusting the Soundbar volume with a TV remote control Adjust the Soundbar volume using the TV’s remote control. •• This function can be used with IR remote controls only. Bluetooth remote controls (remote controls that require pairing) are not supported. •• Set the TV speaker to External Speaker to use this function. •• Manufacturers supporting this function: Samsung, VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, Hisense, RCA TV remote control On/Off 1. Turn Off the Soundbar. 2.
04 CONNECTING THE SOUNDBAR Connecting Electrical Power Use the power components to connect the Soundbar to an electrical outlet in the following order: •• For more information about the required electrical power and power consumption, refer to the label attached to the product. (Label: Bottom of the Soundbar Main Unit) 1. Connect the power cord to the Soundbar. 2. Connect the power cord to a wall socket.
05 USING A WIRED CONNECTION TO THE TV Connecting using an Optical Cable Pre-connection Checklist •• When you use an optical cable and the terminals have covers, be sure to remove the covers. Optical Cable (not supplied) DIGITAL DIGITAL AUDIO IN AUDIO(OPTICAL) IN (OPTICAL) OPTICAL OUT Top of the Soundbar HDMI USB (5V 0.5A) Bottom of the (ARC) Soundbar LED White On -> Off Indicator “Digital Audio In” 1.
06 USING A WIRELESS CONNECTION TO THE TV Connecting via Bluetooth When a Samsung TV is connected using Bluetooth, you can hear stereo sound without the hassle of cables. •• Only one Samsung TV can be connected at a time. •• Samsung TV that supports Bluetooth can be connected. Check the specifications of your TV. The initial connection 1. Press the PAIR button on the Soundbar remote control or press (Source) button on the Soundbar top panel to enter the "Bluetooth" mode.
If the device fails to connect •• If you have an existing Soundbar (e.g., [AV]Soundbar C4-Series) on the list of speakers on the Samsung TV, delete it. •• Then repeat steps 1 through 3. Disconnecting the Soundbar from the Samsung TV Press the (Source) button on the top panel or on the remote control to select the mode other than “Bluetooth”. •• Disconnecting takes time because the Samsung TV must receive a response from the Soundbar. (The time required may differ, depending on the Samsung TV model.
07 CONNECTING AN EXTERNAL DEVICE Connecting using an Optical Cable Optical Cable BD / DVD player / Set-top (not supplied) box / Game console Bottom of the Soundbar DIGITAL DIGITAL AUDIO IN AUDIO(OPTICAL) IN (OPTICAL) Top of the Soundbar OPTICAL OUT HDMI USB (5V 0.5A) (ARC) R - AUDIO - L LED White On -> Off Indicator “Digital Audio In” 1.
08 CONNECTING A USB STORAGE DEVICE You can play music files located on USB storage devices through the Soundbar. USB port DIGITAL DIGITAL AUDIO IN AUDIO(OPTICAL) IN (OPTICAL) POWER POWER DIGITAL AUDIO IN (OPTICAL) USB (5V 0.5A) HDMI USB (5V 0.5A) (ARC) LED White On -> Off Indicator “USB” 1. Connect the USB device to the USB port on the bottom of the product. 2. Press the (Source) button on the top panel or remote control, and then select the “USB” mode. 3.
File Format Type Compatibility list Extension Codec Sampling Rate Bit Rate *.mp3 MPEG1 Layer2 32kHz ~ 48kHz 32kbps ~ 320kbps MPEG1 Layer3 32kHz ~ 48kHz 32kbps ~ 320kbps MPEG2 Layer3 16kHz ~ 24kHz 8kbps ~ 160kbps MPEG2.5 Layer3 8kHz ~ 12kHz 8kbps ~ 160kbps *.wma WMA7/8/9 32kHz ~ 48kHz 32kbps ~ 320kbps *.aac *.m4a AAC-LC (MPEG2/MPEG4 Audio Only) 32kHz ~ 48kHz 32kbps ~ 320kbps *.wav LPCM 32kHz ~ 192kHz 1,024kbps ~ 9,216kbps *.
09 CONNECTING A MOBILE DEVICE Connecting via Bluetooth When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of cables. •• When you connect a paired Bluetooth device with the Soundbar off, the Soundbar automatically turns on. mobile device The initial connection •• When connecting to a new Bluetooth device, make sure the device is within 1 m distance. 1.
Notes on Bluetooth connection •• Locate a new device within 1 m to connect via Bluetooth communication. •• If asked for a PIN code when connecting a Bluetooth device, enter <0000>. •• The Soundbar automatically turns off after 18 minutes in the Ready state. •• The Soundbar may not perform Bluetooth search or connection correctly under the following circumstances: –– If there is a strong electrical field around the Soundbar. –– If several Bluetooth devices are simultaneously paired with the Soundbar.
Bluetooth Power On/Off If a previously paired Bluetooth device tries to pair with the Soundbar when the Bluetooth Power On function is on and the Soundbar is turned off, the Soundbar turns on automatically. 1. Press and hold the SOUND MODE button for more than 5 seconds on the remote while the Soundbar is turned on. 2. Multicolor LED indicator on the Soundbar blinks "Cyan”.
Connecting a Soundbar to a mobile device via NFC function Place your mobile device in the NFC detection area on top of the Soundbar. NFC Top of the Soundbar Bluetooth device NOTES •• Make sure that your mobile device has the NFC function turned on and that the screen is active. •• Bluetooth connection is unavailable when NFC of the mobile device is in card emulation mode. •• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
10 INSTALLING THE WALL MOUNT (OPTIONAL) Installation Precautions •• Install on a vertical wall only. •• Do not install in a place with high temperature or humidity. •• Verify whether the wall is strong enough to support the product’s weight. If not, reinforce the wall or choose another installation point. •• Purchase and use the fixing screws or anchors appropriate for the kind of wall you have (plaster board, iron board, wood, etc.). If possible, fix the support screws into wall studs.
1. NOTES –– If your TV is installed on the wall, install the Soundbar 5cm or more below your TV. –– Use a pencil to mark the holes’ positions. ------ 450 mm------ CENTER LINE 2. 50 mm A B C 6 mm IMPORTANT NOTE –– The installation method shown here is for CONCRETE walls. Installation methods will vary depending on the wall type. For installation on dry wall, we strongly recommend you drill screw support holes into the underlying wood studs. 3.
4. POWER POWER POWER DIGITAL AUDIO IN (OPTICAL) USB (5V 0.5A) 5. POWER POWER DIGITAL AUDIO IN (OPTICAL) USB (5V 0.5A) NOTE –– Supports for wall installation are built into the back of the Soundbar. CAUTION –– Press the Soundbar down with sufficient force to fix it to the wall. If the Soundbar is not firmly fixed to the wall, it could be accidently detached, resulting in personal injury. –– Do not bump into or strike the Soundbar (especially from the bottom).
11 SOFTWARE UPDATE 5. Plug USB into Soudbar and switch to USB source, the software will update automatically and will complete update within 2 minutes. During the update process, the 5 LEDs will start flashing in a loop, and Important: After upgrading, keep the original then the 5 LEDs will all be bright white, and Settings. then the 5 LEDs will flash in a loop again.
•• This product has a DUAL BOOT function. If the firmware fails to update, you can Reset update the firmware again. 5 Sec If LED sequence flashing is not displayed 1. Turn off the Soundbar, disconnect and then reconnect the USB storage device that contains the update files to the Soundbar’s USB port. With the Soundbar on, press the (Volume) buttons on the body at the same time for at least 5 seconds. The LED display changes as shown 2.
12 TROUBLESHOOTING Before seeking assistance, check the following. Soundbar does not turn on. Soundbar does not connect via Bluetooth. ;; Check whether the power cord of the Soundbar is correctly inserted into the outlet. ;; When connecting a new device, switch to Bluetooth Pairing for connection. (Press the PAIR button on the remote control or press the Soundbar works erratically. (Source) button on the body for at least 5 seconds.) ;; After removing the power cord, insert it again.
13 LICENSE Sound drops out when connected via Bluetooth. ;; If your device that is connected via Bluetooth moves too far away from the Soundbar, it may cause the sound to drop Dolby, Dolby Audio, and the double-D symbol out. Move the device closer to the are trademarks of Dolby Laboratories Licensing Soundbar. Corporation. Manufactured under license from ;; If a part of your body is in contact with the Dolby Laboratories. Confidential unpublished Bluetooth transceiver or the product is works.
14 OPEN SOURCE LICENSE NOTICE To send inquiries and requests for questions regarding open sources, contact Samsung Open Source (http://opensource.samsung.com) 15 IMPORTANT NOTES ABOUT SERVICE Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.
16 SPECIFICATIONS AND GUIDE Specifications Model Name HW-C400 USB 5V/0.5A Weight 2.0 kg Dimensions (W x H x D) 641.0 x 66.5 x 107.0 mm Operating Temperature Range +5°C to +35°C Operating Humidity Range 10 % ~ 75 % AMPLIFIER 20W x 2 Rated Output power Supported play formats Bluetooth Port deactivation method LPCM 2ch, Dolby Audio™ (supporting Dolby® Digital), DTS Press and hold the SOUND MODE button for more than 5 seconds to turn off Bluetooth Power function.
INFORMACIÓN DE SEGURIDAD ADVERTENCIAS DE SEGURIDAD PARA REDUCIR EL PELIGRO DE DESCARGA ELÉCTRICA, NO RETIRE LA TAPA (NI LA PARTE TRASERA). NO CONTIENE ELEMENTOS QUE DEBA REEMPLAZAR EL USUARIO. EN CASO DE AVERÍA, SOLICITE LA AYUDA DE PERSONAL ESPECIALIZADO. Consulte la tabla a continuación para obtener una explicación de los símbolos que podrían aparecer en su producto Samsung. ADVERTENCIA •• Para reducir el riesgo de incendio o de descarga eléctrica, no exponga este aparato a la lluvia ni a lahumedad.
PRECAUCIONES 1. Asegúrese de que la fuente de alimentación de CA de su hogar cumpla con los requisitos mencionados en la etiqueta de identificación ubicada en la parte inferior del producto. Instale el producto horizontalmente, sobre una base adecuada (mueble), con espacio suficiente a su alrededor para ventilación 7~10 cm. Asegúrese de que los orificios de ventilación no queden tapados. No coloque la unidad sobre amplificadores o cualquier otro equipo que pueda generar calor.
ÍNDICE 01 Verificación de los componentes 6 02 Información general del producto 7 03 Panel superior de la Soundbar -------------------------- 7 Panel inferior de la Soundbar -------------------------- 8 Uso del control remoto 9 Colocación de las pilas antes de utilizar el control remoto (2 pilas AAA) -------------------------- 9 Cómo usar el control remoto -------------------------- 9 Uso de los botones ocultos (botones con más de una función) -------------------------- 14 Especificac
08 Conectar un dispositivo de almacenamiento USB 21 09 Conexión a un dispositivo móvil 23 10 11 Conexión a través de Bluetooth -------------------------- 23 Conexión de una Soundbar a un dispositivo móvil con la función NFC -------------------------- 26 Instalación del soporte de montaje en la pared (opcional) 27 Precauciones durante la instalación -------------------------- 27 Componentes de soporte -------------------------- 27 Actualización del Software Restablecer 30 -----------------
01 VERIFICACIÓN DE LOS COMPONENTES SOUND MODE WOOFER CH LEVEL Unidad principal de la Soundbar Cable de alimentación (Soundbar) TONE CONTROL Control remoto / Pilas (No disponible en algunos lugares o para algunos modelos) •• Para obtener más información acerca del suministro eléctrico y el consumo de energía, consulte la etiqueta del producto.
02 INFORMACIÓN GENERAL DEL PRODUCTO Panel superior de la Soundbar Panel superior NFC El indicador LED destella, brilla o cambia de color según el modo o estado actual de la Soundbar. El color del indicador LED y la cantidad de luces indican el modo activo como se describe a continuación.
Logotipo de NFC Puede activar la conexión a través de Bluetooth colocando su teléfono en el área de detección de NFC de la Soundbar. •• Cuando conecte el cable de CA, el botón de encendido comenzará a funcionar luego de 4 a 6 segundos. •• Cuando encienda esta unidad, habrá un retraso de 4 a 5 segundos antes de que emita sonido.
03 USO DEL CONTROL REMOTO Colocación de las pilas antes de utilizar el control remoto (2 pilas AAA) Deslice la contratapa en dirección de la flecha hasta retirarla completamente. Inserte 2 baterías AAA (1,5 V) de modo tal que la orientación sea correcta. Vuelva a deslizar la contratapa hasta su posición. Cómo usar el control remoto Encendido Enciende y apaga la Soundbar.
Volumen Mueva el botón hacia arriba o hacia abajo para ajustar el volumen. Indicador El color blanco se mueve hacia la derecha X1 El color blanco se mueve hacia la izquierda X1 Sube el volumen Baja el volumen LED CH LEVEL Puede presionar este botón para ajustar el volumen de cada altavoz. Indicador Parpadeos blancos X1 LED “Center Level” (Control de sonido) Puede presionar el botón para establecer la función de audio. Se puede ajustar el elemento deseado con los botones Arriba/Abajo.
EQ 7 bandas Mantenga presionado el botón (Control de sonido) durante aproximadamente 5 segundos para ajustar el sonido de cada banda de frecuencia. Puede elegir 150 Hz, 300 Hz, 600 Hz, 1,2 kHz, 2,5 kHz, 5 kHz y 10 kHz usando los botones Izquierda/Derecha y puede configurar cada uno entre -6 y +6 con los botones Arriba/Abajo. (Asegúrese de que el modo de sonido se establezca como “Standard”.
SOUND MODE Puede seleccionar el modo de audio que desea presionando el botón. Cada vez que cambia el modo, el LED multicolor parpadea en blanco. (El modo de sonido puede ser diferente según el modelo de TV). Parpadeos blancos X1 Indicador LED “Surround Sound” “Standard” –– Surround Sound Provee un campo acústico más amplio que el estándar. –– Standard Emite el sonido original.
W OO CH LE VE L CO TO NT NE RO L FE R SO M UN OD D E W OO CO TO NT NE RO L CH LE VE L CO TO NT NE RO L CH LE VE L W OO FE R SO M UN OD D E NIVEL de WOOFER (BAJOS) FE R OD D E Presione el botón hacia arriba o hacia abajo para ajustar el nivel de graves entre -6 y +6. Para configurar el nivel de volumen de graves (bajos) en 0 (Predeterminado), presione el botón. (El altavoz de graves no se incluye).
Uso de los botones ocultos (botones con más de una función) Botón oculto Botón del mando a distancia Función WOOFER (Arriba) Encendido/Apagado del control remoto del TV Izquierda (Control de sonido) SOUND MODE Encendido/Apagado de la conexión automática del TV Página de referencia Página 15 Página 19 EQ 7 bandas Página 11 Encendido/Apagado de DRC Página 12 Encendido/Apagado de Bluetooth Power Página 12 Especificaciones de salida para los diferentes modos de efectos de sonido Efecto Surround Sou
Ajuste del volumen de la Soundbar con un control remoto de televisor Ajuste el volumen de la Soundbar con el control remoto del televisor. •• Esta función solo se puede usar con controles remotos IR. Los controles remotos Bluetooth (controles remotos que requieren emparejamiento) no son compatibles. •• Configure el parlante del televisor en Altavoz externo para usar esta función.
04 CONEXIÓN DE LA SOUNDBAR Conexión de la corriente eléctrica Use los componentes de suministro eléctrico en el siguiente orden para conectar la Soundbar a una toma de corriente eléctrica: •• Para obtener más información acerca del suministro eléctrico necesario y el consumo de energía, consulte la etiqueta del producto. (Etiqueta: parte inferior de la unidad principal de la Soundbar) 1. Conecte el cable de alimentación a la Soundbar. 2. Conecte el cable de alimentación a un tomacorriente.
05 USO DE UNA CONEXIÓN CON CABLE AL TV Conexión con un cable óptico Lista de verificación previa a la conexión •• Cuando use un cable óptico y las terminales tengan cubiertas, asegúrese de quitarlas. Cable óptico (no suministrado) DIGITAL DIGITAL AUDIO IN AUDIO(OPTICAL) IN (OPTICAL) OPTICAL OUT Parte superior de la Soundbar HDMI USB (5V 0.5A) de la Parte inferior (ARC) Soundbar Indicador LED Blanco Encendido -> Apagado “Digital Audio In” 1.
06 USO DE UNA CONEXIÓN INALÁMBRICA AL TV Conexión a través de Bluetooth Cuando se conecta un TV Samsung a través de Bluetooth, puede escuchar sonido en estéreo sin cables de por medio. •• Solo se puede conectar un TV Samsung por vez. •• Se puede conectar un TV Samsung que sea compatible con Bluetooth. Compruebe las especificaciones de su TV. La conexión inicial 1.
Si el dispositivo no se puede conectar •• Si tiene una Soundbar existente (p. ej., [AV]Soundbar C4-Series) en la lista de parlantes del TV Samsung, elimínela. •• Luego, repita los pasos 1 a 3. Desconexión de la Soundbar del TV Samsung Presione el botón (Fuente) en el panel superior o en el control remoto para seleccionar el modo que no sea “Bluetooth”. •• La desconexión toma tiempo porque el TV Samsung debe recibir la respuesta de la Soundbar.
07 CONEXIÓN A UN DISPOSITIVO EXTERNO Conexión con un cable óptico BD / Reproductor de DVD / Cable óptico Decodificador / (no suministrado) Consola de juegos Parte inferior de la Soundbar DIGITAL DIGITAL AUDIO IN AUDIO(OPTICAL) IN (OPTICAL) HDMI USB (5V 0.5A) (ARC) Parte superior de la Soundbar OPTICAL OUT R - AUDIO - L Indicador LED Blanco Encendido -> Apagado “Digital Audio In” 1.
08 CONECTAR UN DISPOSITIVO DE ALMACENAMIENTO USB Puede reproducir archivos de música que se encuentran en dispositivos de almacenamiento a través de la Soundbar. Puerto USB DIGITAL DIGITAL AUDIO IN AUDIO(OPTICAL) IN (OPTICAL) POWER POWER DIGITAL AUDIO IN (OPTICAL) USB (5V 0.5A) HDMI USB (5V 0.5A) (ARC) Indicador LED Blanco Encendido -> Apagado “USB” 1. Conecte el dispositivo USB en el puerto USB en la parte inferior del producto. 2.
Lista de compatibilidad Extensión Códec Velocidad de muestreo Velocidad en bits *.mp3 MPEG1 Layer2 32kHz ~ 48kHz 32 ~ 320 kbps MPEG1 Layer3 32kHz ~ 48kHz 32 ~ 320 kbps MPEG2 Layer3 16kHz ~ 24kHz 8 ~ 160 kbps MPEG2.5 Layer3 8kHz ~ 12kHz 8 ~ 160 kbps *.wma WMA7/8/9 32kHz ~ 48kHz 32 ~ 320 kbps *.aac *.m4a AAC-LC (MPEG2/MPEG4 audio únicamente) 32kHz ~ 48kHz 32 ~ 320 kbps *.wav LPCM 32kHz ~ 192kHz 1024 ~ 9216 kbps *.
09 CONEXIÓN A UN DISPOSITIVO MÓVIL Conexión a través de Bluetooth Cuando se conecta un dispositivo móvil a través de Bluetooth, puede escuchar sonido en estéreo sin cables de por medio. •• Cuando conecta un dispositivo Bluetooth emparejado y la Soundbar está apagada, la Soundbar se enciende automáticamente. Dispositivo móvil La conexión inicial •• Cuando conecte un dispositivo Bluetooth nuevo, asegúrese de que el dispositivo esté en un radio de 1 m de distancia. 1.
Notas sobre la conexión a través de Bluetooth •• Ubique un dispositivo nuevo en un radio de 1 m para conectarlo a través de Bluetooth. •• Si le pide un código PIN cuando conecta un dispositivo Bluetooth, ingrese <0000>. •• La Soundbar se apaga automáticamente después de estar 18 minutos en estado Listo. •• Es posible que la Soundbar no realice la conexión o la búsqueda de Bluetooth correctamente en los siguientes casos: –– Si hay un campo eléctrico fuerte cerca de la Soundbar.
Encendido/Apagado de Bluetooth Power Si otro dispositivo con Bluetooth previamente emparejado intenta emparejarse con la Soundbar cuando la función Bluetooth Power Está encendida y la Soundbar está apagada, la Soundbar se enciende automáticamente. 1. Mantenga presionado el botón SOUND MODE durante más de 5 segundos en el control remoto mientras la Soundbar está encendida. 2. El indicador LED multicolor en la Soundbar parpadea en color “Cian”.
Conexión de una Soundbar a un dispositivo móvil con la función NFC Coloque el dispositivo móvil en el área de detección de NFC en la parte superior de la Soundbar. NFC Parte superior de la Soundbar Dispositivo con Bluetooth NOTAS •• Asegúrese de que la función NFC esté activada en el dispositivo móvil y que la pantalla esté encendida. •• La conexión a través de Bluetooth no está disponible cuando la función NFC del dispositivo móvil está en modo emulación de tarjeta.
10 INSTALACIÓN DEL SOPORTE DE MONTAJE EN LA PARED (OPCIONAL) Precauciones durante la instalación •• Instálelo en la pared solo de forma vertical. •• No lo instale en un lugar con altas temperaturas o humedad. •• Verifique si la pared es lo suficientemente resistente como para soportar el peso del producto. Si no lo es, refuerce la pared o elija otro lugar para realizar la instalación.
1. NOTAS –– Si el televisor está instalado en la pared, instale la Soundbar a 5 cm ------ 450 mm------ o más, debajo del televisor. –– Utilice un lápiz para marcar la posición de los orificios. LÍNEA CENTRAL 2. 50 mm A B C 6 mm AVISO IMPORTANTE –– El método de instalación que se muestra aquí es para paredes de HORMIGÓN. Los métodos de instalación variarán según el tipo de pared.
4. POWER POWER POWER DIGITAL AUDIO IN (OPTICAL) USB (5V 0.5A) 5. POWER POWER DIGITAL AUDIO IN (OPTICAL) USB (5V 0.5A) NOTA –– Los soportes para realizar instalaciones en la pared están integrados en la parte posterior de la Soundbar. PRECAUCIÓN –– Presione la Soundbar hacia abajo con la fuerza suficiente para fijarla en la pared. Si la Soundbar no está bien fija en la pared, se podría despegar por accidente y provocar lesiones.
11 ACTUALIZACIÓN DEL SOFTWARE 5. Enchufe la unidad USB en la Soundbar y cambie a fuente USB. La actualización de software comenzará a ejecutarse automáticamente y finalizará dentro de los 2 minutos siguientes. Durante el proceso de actualización, los 5 indicadores LED parpadearán en bucle; luego, los 5 se iluminarán todos de color blanco brillante y, luego, los 5 iniciarán nuevamente una secuencia de parpadeo en bucle. Cuando la actualización haya finalizado, el indicador color cian parpadeará 3 veces.
Restablecer •• Este producto tiene una función DUAL BOOT. Si falla la actualización del firmware, puede actualizarlo nuevamente. 5 Sec Si no se muestra la secuencia de LED parpadeando 1. Apague la Soundbar, desconecte y vuelva a conectar el dispositivo de almacenamiento que contiene los archivos actualizados al puerto USB de la Soundbar. 2. Desconecte el cable de alimentación de la Soundbar, vuelva a conectarlo y luego encienda la Soundbar.
12 SOLUCIÓN DE PROBLEMAS Antes de buscar ayuda, controle lo siguiente. La Soundbar no se enciende. La Soundbar no se conecta mediante Bluetooth. ;; Compruebe si el cable de alimentación de la ;; Cuando conecte un dispositivo nuevo, seleccione el emparejamiento Bluetooth Soundbar se insertó correctamente en el enchufe. para establecer la conexión. (Presione el La Soundbar funciona de forma errática.
13 LICENCIA No hay sonido cuando se conecta mediante Bluetooth. ;; Si el dispositivo que está conectado mediante Bluetooth se aleja demasiado de la Soundbar, eso puede hacer que no haya Dolby, Dolby Audio, and the double-D symbol sonido. Acerque el dispositivo a la are trademarks of Dolby Laboratories Licensing Soundbar. Corporation. Manufactured under license from ;; Si parte de su cuerpo está en contacto con Dolby Laboratories.
14 AVISO SOBRE LICENCIA DE CÓDIGO ABIERTO Para enviar consultas y solicitudes o preguntas sobre fuentes abiertas, comuníquese con Samsung Open Source (http://opensource.samsung.com) 15 NOTA IMPORTANTE SOBRE EL SERVICIO Las figuras e ilustraciones de este Manual del usuario se facilitan sólo como referencia y pueden diferir del aspecto real del producto.
16 ESPECIFICACIONES Y GUÍA Especificaciones Nombre del modelo HW-C400 USB 5V/0,5A Requisitos de electricidad (solo México) 110-240V ~50/60Hz (méxico sólo) Consumo de energía (solo México) 20W (méxico sólo) Peso 2,0 kg Dimensiones (An x Al x Pr) 641,0 x 66,5 x 107,0 mm Rango de temperatura de servicio +5 °C a +35 °C Rango de humedad de servicio 10 % a 75 % AMPLIFICADOR 20W x 2 Potencia nominal de salida Formatos de reproducción compatibles Bluetooth Método de desactivación de puerto LPCM
© 2023 Samsung Electronics Co., Ltd. All rights reserved. Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care Center. Country Samsung Service Center Web Site ` Latin America MEXICO 800-SAMSUNG www.samsung.com/mx/support BRAZIL 0800 555 0000 (Demais cidades e regiões) 4004-0000 (Capitais e grandes centros) www.samsung.