DW80K7050 Series DW80K5050 Series Dishwasher installation guide These installation instructions are intended for use by qualified installers. STOP If you are having problems installing this dishwasher Please call : 1-800-SAMSUNG (726-7864) for assistance : www.samsung.com imagine the possibilities Thank you for purchasing this Samsung product. Installation_DD81-02034A-00_EN.
safety instructions Throughout this manual, you’ll see Warning and Caution notes. These warnings, cautions, and the important safety instructions that follow do not cover all possible conditions and situations that may occur. It’s your responsibility to use common sense, caution, and care when installing, maintaining, and operating the dishwasher. Samsung is not liable for damages resulting from improper use.
GROUNDING INSTRUCTIONS For a permanently connected appliance: This appliance must be connected to grounded metal, a permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. The dishwasher is very heavy. Do not attempt to move or carry a dishwasher alone. Two or more people are needed to move a dishwasher and avoid potential injuries.
contents PREPARING THE DISHWASHER ENCLOSURE 5 5 Product dimensions Enclosure dimensions 6 8 STEP 1 STEP 2 5 INSTALLING THE DISHWASHER 6 9 10 11 13 14 15 16 17 20 21 Check the parts and tools Select the best location for the dishwasher STEP 3 Check water supply requirements and cautions STEP 4 Check the electrical requirements and cautions STEP 5 Unpacking and inspecting the dishwasher STEP 6 Preparing the dishwasher STEP 7 Placing the dishwasher and connecting the hot water supply line STEP 8 Level
preparing the dishwasher enclosure PRODUCT DIMENSIONS 27” (686 mm) Rear view 33 9/10” (860 mm) 01 PREPARING THE DISHWASHER Side view DW80K7050 Series 23 7⁄8” (605 mm) 20 ½” (520 mm) 24 ⅔” (627mm) Side view DW80K5050 Series 5” (128 mm) 2 ⅓” (60 mm) The water supply line, power cable and drain hose should go through this space behind the dishwasher. Then, the power cable run in channels under the dishwasher to connections in the front. 20 ½” (520 mm) 24 ⅔” (627 mm) 24 ½” (621.
installing the dishwasher Be sure that you or your installer follow these instructions closely so that the new dishwasher works properly and that you’re not at risk of injury when washing dishes. STEP 1 CHECK THE PARTS AND TOOLS Before starting on the installation, prepare all the necessary tools and parts required to install the dishwasher. This will save installation time and simplify the installation process. Parts required Provided with the dishwasher. Check when you unbox the dishwasher in Step 5.
Tools required Safety glasses Gloves Flashlight Adjustable wrench Wire stripper Pliers Nipper Tape measure Pencil Phillips screwdriver Flat screwdriver Tubing cutter Cutting knife Hole saw Level Torx t20 Hex L-wrench 02 INSTALLING THE DISHWASHER Electric drill installing the dishwasher _7 Installation_DD81-02034A-00_EN.
installing the dishwasher New installation If the dishwasher is a new installation, most of the installation work must be done before the dishwasher is moved into place. Replacement If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher connections for compatibility with the new dishwasher. Repace the existing connections as necessary.
STEP 3 CHECK WATER SUPPLY REQUIREMENTS AND CAUTIONS • • The hot water supply line pressure must be between 20~120 psi (140~830 kPa). Adjust the water heater to deliver water between 120 ˚F (49 ˚C) ~ 149 ˚F (65 ˚C). - -
installing the dishwasher STEP 4 CHECK THE ELECTRICAL REQUIREMENTS AND CAUTIONS The electrical requirements for the dishwasher are as follows: • In the United States, install in accordance with the National Electric Code/State and Municipal codes and/or local codes. • In Canada, install in accordance with the Canadian Electric Code C22.1-latest edition/Provincial and Municipal codes and/or local codes. • For cable direct connections.
STEP 5 UNPACKING AND INSPECTING THE DISHWASHER Unbox the dishwasher in an open area free of obstruction both around the carton and overhead. We recommend that you retain the carton and all of the packing materials until the dishwasher is fully installed and operational to ensure you have removed all the product’s components from the carton prior to disposal. 02 INSTALLING THE DISHWASHER Unboxing 1. Position the carton right-side-up with top arrows pointing upwards. 2.
installing the dishwasher Plumbing 1. Check the hot water connection on the front left-side of the base of the dishwasher. The mounting plate should be secured to the front of the base, the threads inside the connection should be smooth and shiny, and the area should be clean and free of any debris. 2. Check the plastic Brake and Sensor cases to ensure these assemblies are not cracked and that all connections are secure. 3.
2. Ensure that the circuit breaker and water supply valve are turned off before proceeding with the following steps. CAUTION Before you move or lay down the dishwasher for installation, make sure to adjust the height of the legs so the legs are as short as possible. This prevents the legs from breaking. Level the dishwasher by adjusting the height of the legs after you have the dishwasher in place.
installing the dishwasher STEP 7 PLACING THE DISHWASHER AND CONNECTING THE HOT WATER SUPPLY LINE 1. Adjust the three leveling legs at the bottom of the dishwasher after measuring the height of the cabinet opening from under the countertop to the floor. (See Step 8, Leveling the Dishwasher.) 2. Locate the hot water supply line and the power cable. 3. Place the dishwasher so that the power cable is in the right channel of the base of the dishwasher.
STEP 8 LEVELING THE DISHWASHER 02 INSTALLING THE DISHWASHER 1. Open the door and place the level against the top of the tub on the inside and check if the the dishwasher is level. If it is not level, rotate the leveling legs at the bottom front of the dishwasher until the dishwasher is level. See the first note below for instructions on adusting the height of the front legs. 2. Use the level to check if the dishwasher is level front to back, as shown in the figure to the right.
installing the dishwasher STEP 9 SECURING THE DISHWASHER You must fix the dishwasher to the countertop or cabinet side walls for additional stability and safety. 1. If the countertop is made of wood or the material will not be damaged by drilling, follow the instructions in 2-1 below. If the countertop is made of granite, marble, or any other material that can be damaged by drilling, follow the instructions in 2-2 below. 2-1.
installing the dishwasher Case 2. With disposal With disposal Disposal with an air gap Without an air gap Air gap Drain hose Hose clamp Hose clamp 3. Check the size of the sink’s drain hose connector. If needed, cut the drain hose so its end fits onto the sink connector (1" or 5/8" - as shown in Figure 11 below). If the end of the drain hose does not fit onto the drain hose connector of the sink, use an adaptor purchasable at a plumbing/hardware supply store. 4.
02 INSTALLING THE DISHWASHER 1 in. (25 mm) 5 /8 in. (16 mm) If necessary, cut off the dotted line of the drain hose to fit the size. Secure the drain hose to the sink wall using cable ties or other fastening materials. Otherwise, the drain hose may bend at the end, causing a drainage problem or excessive supply of water. Dishwasher Sink Drain hose Min. 30 in. (762 mm) Min. 20 in. (508 mm) installing the dishwasher _19 Installation_DD81-02034A-00_EN.
installing the dishwasher STEP 11 WIRING CONNECTIONS 1. Before connecting the power cable to the dishwasher, make sure the circuit breaker is off. 2. In the junction box located at the front bottom right of the dishwasher, find the three power wires from the dishwasher including the grounding line. 3. Pass the power cable through the strain relief, and then into the junction box (Figure 14). 4.
STEP 12 COMPLETING THE INSTALLATION Open the door and remove all foam, paper packaging, and unnecessary parts. Turn on the circuit breaker you turned off before you began the installation. Open the water supply valve to supply water to the dishwasher. Turn on the dishwasher, and then select and run a cycle. Check if the power turns on correctly and if there is any water leakage while the dishwasher is operating. If no errors occur while it is operating, turn off the dishwasher, and then go to Step 5 below.
specifications Power supply 120 V, 60 Hz AC only Water pressure 20 ~ 120 psi (140 ~ 830 kPa) Dimensions (Width×Depth×Height) 23 ⅞ x 24 ¾ x 33 9⁄10 in. (605 x 627 x 860 mm) (DW80K7050 Series) 23 ⅞ x 24 ½ x 33 9⁄10 in. (605 x 621.5 x 860 mm) (DW80K5050 Series) Nominal inlet water temperature 120 ˚F (49 ˚C) Specifications are subject to change without notice for quality improvement purposes. The actual appearance of the dishwasher may differ from the illustrations in this manual.
notes Installation_DD81-02034A-00_EN.
DD81-02034A-00 Installation_DD81-02034A-00_EN.
Serie DW80K7050 Serie DW80K5050 Lavavajillas guía de instalación Estas instrucciones de instalación están dirigidas a instaladores calificados. ATENCIÓN Si tiene problemas al instalar esta lavavajillas Llame al: 1-800-SAMSUNG (726-7864) para recibir asistencia: www.samsung.com imagine las posibilidades Gracias por adquirir este producto Samsung. Installation_DD81-02034A-00_MES.
instrucciones de seguridad A lo largo de este manual, encontrará notas de Advertencia y Precaución. Las siguientes advertencias, precauciones e instrucciones de seguridad importantes no cubren todas las posibles condiciones y situaciones que pueden ocurrir. Es su responsabilidad actuar con sentido común, precaución y cuidado cuando instale, realice el mantenimiento y ponga en funcionamiento la lavavajillas. Samsung no se responsabiliza por los daños ocasionados por un uso inadecuado.
INSTRUCCIONES DE CONEXIÓN A TIERRA Para un electrodoméstico con conexión permanente: Este electrodoméstico debe estar conectado a un metal con conexión a tierra, un sistema de cableado permanente o a un conductor con conexión a tierra del equipo a los conductores del circuito y a la terminal con conexión a tierra del equipo. La lavavajillas es muy pesada. No intente mover o trasladar una lavavajillas usted solo. Se necesitan dos o más personas para mover una lavavajillas y evitar lesiones potenciales.
contenido PREPARACIÓN DEL ESPACIO PARA LA LAVAVAJILLAS 5 5 Dimensiones del producto Dimensiones del espacio 6 8 PASO 1 PASO 2 9 PASO 3 10 PASO 4 11 12 14 PASO 5 PASO 6 PASO 7 15 16 17 20 21 PASO 8 PASO 9 PASO 10 PASO 11 PASO 12 22 Especificaciones 5 INSTALACIÓN DE LA LAVAVAJILLAS 6 ESPECIFICACIONES Verificación de las piezas y las herramientas Elección de la mejor ubicación para la lavavajillas Verificación de los requisitos para el suministro de agua y precauciones Verificación de los requisi
preparación del espacio para la lavavajillas DIMENSIONES DEL PRODUCTO 27” (686 mm) Vista posterior 33 9/10” (860 mm) 01 PREPARACIÓN DE LA LAVAVAJILLAS Vista lateral Serie DW80K7050 23 7⁄8” (605 mm) 20 ½” (520 mm) 24 ⅔” (627 mm) El conducto, el cable de alimentación y la manguera de desagüe deberían pasar por este espacio detrás de la lavavajillas. Luego, cable de alimentación pasa a través de canales debajo de la lavavajillas hacia las conexiones de la parte delantera.
instalación de la lavavajillas Asegúrese de que usted o su instalador siga estas instrucciones minuciosamente para que su nueva lavavajillas funcione adecuadamente y no existan riesgos de sufrir lesiones al lavar la vajilla. PASO 1 VERIFICACIÓN DE LAS PIEZAS Y LAS HERRAMIENTAS Antes de comenzar la instalación, prepare todas las herramientas y piezas necesarias requeridas para instalar la lavavajillas. Esto ahorrará tiempo y simplificará el proceso de instalación.
Herramientas requeridas Lentes de seguridad Guantes Linterna Llave ajustable Alicate pelacable Pinza Alicate de corte Cinta métrica Lápiz Destornillador Phillips Destornillador plano Cortatubos Cúter Fresa para escariar Nivel Torx t20 Llave en forma de L para cabezas hexagonales 02 INSTALACIÓN DE LA LAVAVAJILLAS Taladro eléctrico instalación de la lavavajillas _7 Installation_DD81-02034A-00_MES.
instalación de la lavavajillas Instalación nueva Si la instalación de la lavavajillas es nueva, la mayor parte del trabajo debe realizarse antes de colocar la máquina en su lugar. Reemplazo Si esta lavavajillas reemplaza a otra, debe verificar que las conexiones existentes sean compatibles con la nueva lavavajillas. Reemplace las conexiones existentes si fuera necesario.
PASO 3 • • VERIFICACIÓN DE LOS REQUISITOS PARA EL SUMINISTRO DE AGUA Y PRECAUCIONES La presión del conducto de agua caliente debe estar entre 20 y 120 psi (140 y 830 kPa). Ajuste el calentador de agua para obtener una temperatura de agua entre 120 ˚F (49 ˚C) y 149 ˚F (65 ˚C). - La lavavajillas debe estar conectada al suministro de agua caliente con una temperatura entre 120 ˚F (49 ˚C) y 149 ˚F (65 ˚C). Este rango de temperatura ofrece un mejor resultado en el lavado y un ciclo más corto.
instalación de la lavavajillas PASO 4 VERIFICACIÓN DE LOS REQUISITOS ELÉCTRICOS Y ADVERTENCIAS Los requisitos eléctricos para la lavavajillas son los siguientes: • En los Estados Unidos, instalar de conformidad con el Código Eléctrico Nacional/códigos estatales y municipales y/o códigos locales. • En Canadá, instalar de conformidad con el Código Eléctrico Canadiense C22.1-última edición/códigos provinciales y municipales y/o códigos locales. • Para conexiones directas de cable.
PASO 5 DESEMPAQUE E INSPECCIÓN DE LA LAVAVAJILLAS Desempaque la lavavajillas en una zona libre de obstrucciones ya sea alrededor de la caja como en la parte superior. Recomendamos que conserve la caja y todos los materiales del empaque hasta que la lavavajillas esté completamente instalada y en funcionamiento para asegurarse de que haya retirado todas las piezas del producto de la caja antes de desecharla. 1. Ubique el lado derecho de la caja con las flechas superiores señalando hacia arriba. 2.
instalación de la lavavajillas Cañerías 1. Verifique la conexión de agua caliente en el lado izquierdo delantero de la base de la lavavajillas. La placa de montaje debe estar asegurada a la parte delantera de la base, las roscas de la conexión deben ser lisas y brillosas y la zona debe estar limpia y libre de fragmentos. 2. Verifique el empaque de plástico del Freno y del Sensor para asegurarse de que estos montajes no estén dañados y que todas las conexiones estén aseguradas. 3.
2. Asegúrese que el disyuntor y la válvula del suministro de agua estén desactivados antes de continuar con los siguientes pasos. PRECAUCIÓN Antes de mover o apoyar la lavavajillas para su instalación, debe asegurarse de ajustar la altura de las patas de modo que estas sean lo más cortas posible. Esto evita que las patas se rompan. Nivele la lavavajillas ajustando la altura de las patas luego de poner la máquina en su lugar.
instalación de la lavavajillas PASO 7 COLOCACIÓN DE LA LAVAVAJILLAS Y CONEXIÓN DEL CONDUCTO DEL SUMINISTRO DE AGUA CALIENTE 1. Regule las tres patas niveladoras en la parte inferior de la lavavajillas después de medir la altura de la abertura del gabinete desde abajo de la encimera hasta el piso. (Ver el Paso 8, Nivelación de la lavavajillas.) 2. Ubique el conducto del agua caliente y el cable de alimentación. 3.
PASO 8 NIVELACIÓN DE LA LAVAVAJILLAS 02 INSTALACIÓN DE LA LAVAVAJILLAS 1. Abra la puerta y coloque el nivel contra la parte superior de la cuba desde adentro y verifique si la lavavajillas está nivelada. Si no lo está, gire las patas niveladoras en la parte inferior delantera de la lavavajillas hasta que quede nivelada. Vea la primera nota debajo de las instrucciones sobre el ajuste de la altura de las patas delanteras. 2.
instalación de la lavavajillas PASO 9 FIJACIÓN DE LA LAVAVAJILLAS La lavavajillas debe fijarse a la encimera o a las paredes laterales para mayor estabilidad y seguridad. 1. Si la encimera está hecha de madera de un material que no se daña por la perforación, siga las siguientes instrucciones en 2-1. Si la encimera es de granito, mármol o cualquier otro material que pueda dañarse al perforarlo, siga las siguientes instrucciones en 2-2. 2-1.
02 INSTALACIÓN DE LA LAVAVAJILLAS Atornillado a la encimera Tapa del separador de la cuba Atornillado a la pared lateral PASO 10 CONEXIÓN DE LA MANGUERA DE DESAGÜE 1. Verifique las piezas del fregadero a las cuales se conectará la manguera de desagüe. 2. Hay muchas maneras de insertar la manguera de desagüe en el conector de la manguera de desagüe del fregadero, como se muestra en las siguientes figuras.
instalación de la lavavajillas Caso 2. Con triturador Con triturador Sin un espacio de aire Triturador con un espacio de aire Espacio de aire Manguera de desagüe Abrazadera de manguera Abrazadera de manguera 3. Verifique el tamaño del conector de la manguera de desagüe del fregadero. Si es necesario, corte la manguera de desagüe para que encaje en el conector del fregadero (1" o 5/8" - como se muestra en la Figura 11 siguiente).
02 INSTALACIÓN DE LA LAVAVAJILLAS 1 pulgada (25 mm) 5 /8 pulgada (16 mm) Si es necesario, corte por la línea punteada de la manguera de desagüe para que se adapte al tamaño. Asegure la manguera de desagüe a la pared del fregadero con uniones de cables o con otros materiales de fijación. De lo contrario, el extremo de la manguera de desagüe puede doblarse y causar un problema de drenaje o un suministro de agua excesivo.
instalación de la lavavajillas PASO 11 CONEXIONES DEL CABLEADO 1. Antes de conectar el cable de alimentación a la lavavajillas, asegúrese de desactivar el disyuntor. 2. En la caja de conexiones que se encuentra ubicada en la parte delantera derecha inferior de la lavavajillas, busque los tres cables de alimentación de la lavavajillas inclusive la conexión a tierra. 3. Pase el cable de alimentación al alivio de tensión, y luego dentro de la caja de conexiones (Figura 14). 4.
PASO 12 FINALIZACIÓN DE LA INSTALACIÓN Abra la puerta y quite todas las piezas innecesarias, goma espuma y empaque de papel. Active el disyuntor desactivado antes de comenzar la instalación. Abra la válvula del suministro de agua para suministrar agua a la lavavajillas. Encienda la lavavajillas y luego seleccione y ejecute un ciclo. Verifique si el electrodoméstico se enciende correctamente o si hay alguna pérdida de agua mientras la lavavajillas está en funcionamiento.
especificaciones Suministro eléctrico Solamente 120 V, 60 Hz CA Presión de agua 20 - 120 psi (140 - 830 kPa) Dimensiones (Ancho × Profundidad × Altura) 23 ⅞ x 24 ¾ x 33 9⁄10 pulgadas (605 x 627 x 860 mm) (serie DW80K7050) 23 ⅞ x 24 ½ x 33 9⁄10 pulgadas (605 x 621.5 x 860 mm) (serie DW80K5050) Temperatura nominal del agua en la entrada 120 ˚F (49 ˚C) Las especificaciones están sujetas a cambios sin previo aviso a los efectos de las mejoras de calidad.
notas Installation_DD81-02034A-00_MES.
DD81-02034A-00 Installation_DD81-02034A-00_MES.