CTN464FB Series CTN464TB Series CTN464NB Series CTN464EB Series CTN464DB Series CTN464KB Series Induction Hob user manual imagine the possibilities ENGLISH Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.com/register CTN464FB01_XEO_00336A_EN.
using this manual Please take the time to read this owner’s manual, paying particular attention to the safety information contained in the following section, before using your appliance. Keep this manual for future reference. If transferring ownership of the appliance, please remember to pass the manual on to the new owner. IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS.
safety instructions WARNING ELECTRICAL SAFETY Be sure the appliance is properly installed and grounded by a qualified technician. The appliance should be serviced only by qualified service personnel. Repairs carried out by unqualified individuals may cause injury or serious malfunction. If your appliance is in need of repair, contact your local service centre. Failure to follow these instructions may result in damage and void the warranty.
WARNING SAFETY DURING USE This appliance is to be used only for normal cooking and frying in the home. It is not designed for commercial or industrial use. Never use the hob for heating the room. Take care when plugging electrical appliances into mains sockets near the hob. Mains leads must not come into contact with the hob. Overheated fat and oil can catch fire quickly. Never leave surface units unattended when preparing foods in fat or oil, for example, when cooking chips.
WARNING SEVERE WARNING SIGNS FOR INSTALLATION The installation of this appliance must be performed by a qualified hob service technician trained by the manufacturer. Please see the section “Installing your Hob”. Plug the power cord into the proper wall socket or higher and use the socket for this appliance only. Plug the power plug into the wall socket firmly. In addition, do not use an extension cord. The installation of this appliance must be performed by a qualified technician or service company.
Plug the power plug into the wall socket in the right direction so that the cord runs towards the floor. - If you plug the power plug into the socket in the opposite direction, the electric wires within the cable may be damaged and this may result in electric shock or fire. Plug the power plug into the wall socket firmly. Do not use a damaged power plug, damaged power cord or loose wall socket. - This may result in electric shock or fire. Do not pull or excessively bend the power cord.
The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. WARNING : Accessible parts may become hot during use. To avoid burns young children should be kept away.
Do not insert fingers, foreign substances or metal objects such as pins or needles into the inlet, outlet, and holes. If foreign substances are inserted into any of these holes, unplug the power plug from the wall socket and contact your product provider or nearest service centre. - Failure to do so may result in electric shock or injury. NEVER fill the container to the top and choose a container that is wider at the top than at the bottom to prevent the liquid from boiling over.
Small amounts of food require shorter cooking or heating time. If normal times are allowed they may overheat and burn. Children should be supervised to ensure that they do not play with the appliance. Any spillage should be removed from the lid before opening and the hob surface should be allowed to cool before closing the lid (Model which has lid only). - This may result in electric shock, fire, problems with the product, or injury. Do not operate the appliance with wet hands.
WARNING CAUTION SIGNS FOR CLEANING The hob should be cleaned regularly and any food deposits removed. Failure to maintain the hob in a clean condition could lead to deterioration of the surface that could adversely affect the life of the appliance and possibly result in a hazardous situation. Take care not to hurt yourself when cleaning the appliance (external/internal). - You may hurt yourself on the sharp edges of the appliance. Do not clean the appliance with a steam cleaner.
contents INSTALLING THE HOB Regulations and compliance Safety instructions for the installer Connecting to the mains power supply Installing into the countertop Cooking zones Control panel Components Induction heating The key features of your appliance Safety shutoff Residual heat indicator Temperature detection Initial cleaning HOB USE 20 21 21 21 22 22 23 23 23 24 24 25 26 26 27 28 CLEANING AND CARE 29 30 30 Cookware for induction cooking zones Suitability test Size of pans Operating noises Using su
installing the hob WARNING Be sure the new appliance is installed and grounded only by qualified personnel. Please observe this instruction. The warranty will not cover any damage that may occur as a result of improper installation. Technical data is provided at the end of this manual.
CONNECTING TO THE MAINS POWER SUPPLY Before connecting, check that the nominal voltage of the appliance, that is, the voltage stated on the rating plate, corresponds to the available supply voltage. The rating plate is located on the lower casing of the hob. Shut off power to circuit before connecting wires to circuit.
INSTALLING INTO THE COUNTERTOP Make a note of the serial number on the appliance rating plate prior to installation. This number will be required in the case of requests for service and is no longer accessible after installation, as it is on the original rating plate on the underside of the appliance. Pay special attention to the minimum space and clearance requirements. Secure the brackets at both sides with the provided screws before mounting the hob onto the brackets. Min. 50 mm Min.
installing the hob 90 ° x 4 ø2 = 490±1 100 100 = installing the hob _15 CTN464FB01_XEO_00336A_EN.
parts and features m COOKING ZONES m m 0 18 16 0 m 2 1 18 0 0 21 3 m m 4 m m 5 1. 2. 3. 4. 5. Induction cooking zone 1400 W with Power Boost 2000 W Induction cooking zone 1800 W with Power Boost 2600 W Induction cooking zone 2200 W with Power Boost 3200 W Induction cooking zone 1800 W with Power Boost 2600 W Control panel CONTROL PANEL 1 5 1. 2. 3. 4. 5. 6. 7. 8.
COMPONENTS Installation brackets Screws INDUCTION HEATING • The Principle of Induction Heating: When you place your cookware on a cooking zone and you turn it on, the electronic circuits in your induction hob produce “induced currents” in the bottom of the cookware which instantly raise cookware’s temperature.
THE KEY FEATURES OF YOUR APPLIANCE • • • • • • • • • • • • Ceramic glass cooking surface : The appliance has a ceramic glass cooking surface and four rapid - response cooking zones. Touch control sensors : Your appliance is operated using touch control sensors. Easy cleaning : The advantage of the ceramic glass cooking surface and the control sensors is their accessibility for cleaning. The smooth, flat surface is easy to clean.
SAFETY SHUTOFF Heat setting Switch off 1-3 After 6 hours 4-6 After 5 hours 7-9 After 4 hours 10-15 After 1.5 hours If the Hob is overheated because of abnormal operation, And the Hob will be switched off. will be displayed. parts and features If one of the cooking zones is not switched off or the heat setting is not adjusted after an extended period of time, that particular cooking zone will automatically switch itself off.
TEMPERATURE DETECTION If for any reason the temperatures on any of the cooking zones were to exceed the safety levels, should this happen then the cooking zone will automatically reduce to a lower power level. When you have finished using the hob, the cooling fan will continue to run until the hob’s electronics has cooled down. And the cooling fan switched itself on and off depending upon the termperature of the electronics.
SUITABILITY TEST Cookware is suitable for induction cooking, if a magnet sticks to the bottom of the cookware and cookware is labelled as suitable by the cookware manufacturer. hob use SIZE OF PANS Induction cooking zones adapt automatically to the size of the bottom of the cookware up to a cerain limit. However the magnetic part of the bottom of the cookware must have a minimum diameter depending upon the size of the cooking zone.
USING SUITABLE COOKWARE Better pans produce better results. • You can recognise good pans by their bases. The base should be as thick and flat as possible. • When buying new pans, pay particular attention to the diameter of the base. Manufacturers often give only the diameter of the upper rim. • Do not use pans which have damaged bases with rough edges or burrs. Permanent scratching can occur if these pan are slid across the surface. • When cold, pan bases are normally bowed slightly inwards (concave).
SWITCHING THE APPLIANCE ON 1. Touch the Lock control sensor for approximately 3 seconds. approx 1 sec. hob use 2. The appliance is switched on using the On/Off sensor. control Touch the On/Off control sensor for 1 second. The digital displays will show . After the On/Off control sensor has been actuated to switch on your appliance, a heat setting must be selected within approximately 10 seconds. Otherwise, the appliance will switch itself off for safety reasons. SELECT COOKING ZONE AND HEAT SETTING 1.
SWITCHING A COOKING ZONE OFF To switch off a cooking zone, return the setting to by using the control panel’s control sensor. To switch off more quickly, touch the corresponding cooking zone’s key twice. USING THE CHILD SAFETY LOCK You can use the child safety lock to safeguard against unintentionally turning on a cooking zone and activating the cooking surface.
TIMER There are two ways to use the timer: hob use Using the timer as a safety shutoff: If a specific time is set for a cooking zone, the cooking zone will shut itself off once this period of time has elapsed. This function can be used for multiple cooking zones simultaneously. Using the timer to count down: The countdown timer cannot be used if a cooking zone has been switched on. Setting the safety shutoff The cooking zone(s) for which you want to apply the safety shutoff must be switched on. 1.
Countdown timer For the countdown timer to be used, the appliance must be switched on but all the cooking zones must be switched off. 1. Touch the Timer control sensor. will appear in the timer display. 2. Set the desired period of time using the Timer setting selectors ( or ). The countdown timer function is now activated and the remaining time appears in the timer display. sensor. and change To adjust the remaining time, touch the Timer control the setting using the Timer setting selectors ( or ).
WATER BOILING 1. Touch the corresponding cooking zone’s key. hob use 2. Touch the Water boiling sensor. 3. Set the desired power level which will be used after water boiling. After water boiling, the cooking zone will automatically reduce to this power level and an acoustic signal sounds. WARNING Use Water boiling fuction only to heat water. Never leave the hob unattended when in use. This may result in fire. hob use _27 CTN464FB01_XEO_00336A_EN.
SUGGESTED SETTINGS FOR COOKING SPECIFIC FOODS The figures in the table below are guidelines. The heat settings required for various cooking methods depend on a number of variables, including the quality of the cookware being used and the type and amount of food being cooked.
cleaning and care HOB Cleaning agents must not come into contact with a heated ceramic glass surface: All cleaning agents must be removed with adequate amounts of clean water after cleaning because they can have a caustic effect when the surface becomes hot. Do not use any aggressive cleaners such as grill or oven sprays, scouring pads or abrasive pan cleaners. Clean the ceramic glass surface after each use when it is still warm to the touch. This will prevent spillage from becoming burnt onto the surface.
Problem Dirt 1. Remove burnt-on sugar, melted plastic, aluminium foil or other materials with a glass scraper immediately and while still hot. WARNING There is a risk of burning yourself when the glass scraper is used on a hot cooking zone: 2. Clean the hob as normal when it has cooled down. If the cooking zone on which something has melted has been allowed to cool, warm it up again for cleaning.
warranty and service FAQS AND TROUBLESHOOTING WARNING Repairs to the appliance are to be performed only by a qualified service technician. Improperly effected repairs may result in considerable risk to the user. If your appliance needs repair, please contact your customer service centre. What should I do if the cooking zones are not functioning? Check for the following possibilities: • The fuse in the house wiring (fuse box) is intact. If the fuses trip a number of times, call an authorised electrician.
What should I do if the display is illuminated? Check for the following: • The hob is overheated because of abnormal operation. • After hob is cooled down, press the “On/Off” control sensor for resetting. What should I do if the display is illuminated? Check for the following: • Cookware is unsuitable or too small or no cookware has been placed on the cooking zone • If you use suitable cookware, displayed message will automatically disapear.
technical data TECHNICAL DATA Worktop cut - out dimensions 575 mm Depth 505 mm Height 52 mm Width 560 mm Depth 490 mm Corner radius 3 mm 220 - 240 V ~ 50 / 60 Hz Connection voltage Maximum connected load power Weight technical data Appliance dimensions Width 7.2 kW Net 11.3 kg Gross 14.
note CTN464FB01_XEO_00336A_EN.
note CTN464FB01_XEO_00336A_EN.
AUSTRIA 0810 - SAMSUNG (7267864, € 0.07/min) BELGIUM 02-201-24-18 DENMARK 70 70 19 70 FINLAND 030 - 6227 515 FRANCE 01 48 63 00 00 GERMANY ITALIA GREECE LUXEMBURG NETHERLANDS NORWAY PORTUGAL SPAIN 01805 - SAMSUNG (726-7864 € 0,14/Min) 800-SAMSUNG(726-7864) 80111-SAMSUNG (80111 7267864) from land line, local charge / 210 6897691 from mobile 261 03 710 www.samsung.
