Click the model name of your machine: CLX-3170FN, CLX-3175FN, CLX-3175FW CLX-3175, CLX-3175N Multi Functional Printer User’s Guide imagine the possibilities Thank you for purchasing a Samsung product.
features of your new laser product Your new machine is equipped with a number of special features that improve the quality of the documents you print. With the machine, you can: SPECIAL FEATURES Print with excellent quality and speed • You can print in a full range of colors using cyan, magenta, yellow, and black. • You can print with a resolution of up to 2400 x 600 dpi. See Software section. • Your machine prints A4-sized paper at up to 16 ppm and letter-sized paper at up to 17 ppm.
FEATURES BY MODELS The machine is designed to support all of your document needs – from printing and copying, to more advanced networking solutions for your business. Basic features of this machine include: FEATURES CLX-3170FN CLX-3175FN CLX-3175FW USB 2.0 USB Memory Interface PictBridge ADF (Automatic Document Feeder) Network Interface Ethernet 10/100 Base TX wired LAN Network interface 802.
FINDING MORE INFORMATION You can find information for setting up and using your machine from the following resources, either as a print-out or onscreen. Quick Install Guide Provides information on setting up your machine and this requires that you follow the instructions in the guide to prepare the machine.
safety information IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS What the icons and signs in this user’s guide mean: Hazards or unsafe practices that may result in severe personal injury or death. WARNING Hazards or unsafe practices that may result in minor personal injury or property damage. CAUTION CAUTION To reduce the risk of fire, explosion, electric shock, or personal injury when using your laser MFP, follow these basic safety precautions: Do NOT attempt. Do NOT disassemble. Do NOT touch.
13. Unplug the machine from the telephone jack, PC and AC wall outlet and refer servicing to qualified service personnel under the following conditions: • When any part of the power cord, plug or connecting cable is damaged or frayed. • If liquid has been spilled into the machine. • If the machine has been exposed to rain or water. • If the machine does not operate properly after instructions have been followed. • If the machine has been dropped, or the cabinet appears damaged.
OZONE SAFETY During normal operation, this machine produces ozone. The ozone produced does not present a hazard to the operator. However, it is advisable that the machine be operated in a well ventilated area. If you need additional information about ozone, request your nearest Samsung dealer. MERCURY SAFETY Contains Mercury, Dispose According to Local, State or Federal Laws.(U.S.A.
RADIO FREQUENCY EMISSIONS FCC Information to the User This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
FAX BRANDING The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone facsimile machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission the following information: (1) the date and time of transmission (2) identification of either business, business entity or individual sending the message; and (3) telephone number of ei
REPLACING THE FITTED PLUG (FOR UK ONLY) Important The mains lead for this machine is fitted with a standard (BS 1363) 13 amp plug and has a 13 amp fuse. When you change or examine the fuse, you must re-fit the correct 13 amp fuse. You then need to replace the fuse cover. If you have lost the fuse cover, do not use the plug until you have another fuse cover. Contact the people from you purchased the machine. The 13 amp plug is the most widely used type in the UK and should be suitable.
European Radio Approval Information (for products fitted with EU-approved radio devices) Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz/5 GHz band, may be present (embedded) in your printer system which is intended for home or office use. This section is only applicable if these devices are present. Refer to the system label to verify the presence of wireless devices.
REGULATORY COMPLIANCE STATEMENTS Wireless Guidance Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz/5 GHz Band, may be present (embedded) in your printer system. The following section is a general overview of considerations while operating a wireless device. Additional limitations, cautions, and concerns for specific countries are listed in the specific country sections (or country group sections).
OPENSSL LICENSE Copyright (c) 1998-2001 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
contents 2 5 INTRODUCTION 18 GETTING STARTED 23 LOADING ORIGINALS AND PRINT MEDIA 37 14_Contents Features of your new laser product Safety information 18 18 18 19 20 20 21 22 22 22 Machine overview Front view Rear view Control panel overview Understanding the Status LED Acknowledging the status of the toner cartridge Menu overview Supplied software Printer driver features Printer driver 23 24 24 24 24 25 25 25 25 25 26 26 27 27 27 28 29 29 30 30 31 31 31 33 35 35 35 35 35 35 35 36 36 36 Setting u
contents COPYING 44 SCANNING 47 BASIC PRINTING 51 FAXING 52 40 41 42 43 43 43 Guidelines for special print media Changing the size of the paper in the paper tray Printing on special print materials Feeding the print material manually Setting the paper size and type 44 44 44 44 44 45 45 45 45 45 46 46 46 46 Copying Changing the settings for each copy Darkness Original Type Reduced or enlarged copy Changing the default copy settings ID card copying Using special copy features 2-up or 4-up copying P
contents USING USB MEMORY DEVICE 60 MAINTENANCE 63 16_Contents 55 55 55 55 55 55 56 56 56 56 57 57 58 58 58 Changing receiving modes Receiving automatically in Fax mode Receiving manually in Tel mode Receiving manually using an extension telephone Receiving automatically in Ans/Fax mode Receiving faxes using DRPD mode Receiving in secure receiving mode Activating secure receiving mode Receiving faxes in memory Forwarding faxes Fax setup Changing the fax setup options Changing the default document set
contents TROUBLESHOOTING 72 ORDERING SUPPLIES 87 SPECIFICATIONS 88 72 72 72 73 73 73 73 74 76 79 79 79 80 82 83 84 84 85 86 Tips for avoiding paper jams Clearing document jams Exit misfeed Roller misfeed Clearing paper jams In the tray 1 In the fuser unit area In the paper exit area Understanding display messages Solving other problems Paper feeding Printing problems Printing quality problems Copying problems Scanning problems Fax problems Common Windows problems Common Linux problems Common Macintosh
introduction These are the main components of your machine: This chapter includes: • • • • Machine overview Control panel overview Understanding the Status LED Acknowledging the status of the toner cartridge • • • Menu overview Supplied software Printer driver features MACHINE OVERVIEW Front view Rear view 1 Document width guides 9 Document output tray 2 ADF 10 USB memory port 3 Control panel 11 Toner cartridge 4 Output support 12 Imaging unit 5 Front cover 13 Waste toner container
CONTROL PANEL OVERVIEW 1 2 3 4 ID Copy Direct USB You can copy both sides of the ID Card like a driver’s license to a single side of paper. (See "ID card copying" on page 45.) 16 Allows you to directly print files stored on a USB Memory device when it is inserted into the USB memory port on the front of your machine. (See "About USB memory" on page 60.) 17 Stop/Clear Display Shows the current status and prompts during an operation.
UNDERSTANDING THE STATUS LED The color of the Status LED indicates the machine's current status. STATUS DESCRIPTION • • Off • Green Blinking • • The machine is powered off-line. The machine is in power save mode. When data is received, or any button is pressed, it switches to on-line automatically. Wireless function can not be used. • The machine is powered on and can be used. Blue On • Wireless function can be used.
MENU OVERVIEW The control panel provides access to various menus to set up the machine or use the machine’s functions. These menus can be accessed by pressing Menu. Refer to the following diagram. Some menus may not appear in the display depending on options or models. If so, it is not applicable to your machine. .
SUPPLIED SOFTWARE PRINTER DRIVER FEATURES After you have set up your machine and connected it to your computer, you must install the printer software. If you are a Windows or Macintosh OS, install the software from the supplied CD and if you are a Linux OS user, download the software from the Samsung website (www.samsung.com/ printer) and install.
getting started This chapter gives you step-by-step instructions for setting up the machine. This chapter includes: • • • • Setting up the hardware System requirements Setting up the network Using a wired network SETTING UP THE HARDWARE This section shows the steps to set up the hardware which is explained in the Quick Install Guide. Make sure you read Quick Install Guide and complete following steps. 1. Select a stable location. Select a level, stable place with adequate space for air circulation.
SYSTEM REQUIREMENTS Macintosh Before you begin, ensure that your system meets the following requirements: REQUIREMENT (RECOMMENDED) OPERATING SYSTEM Windows CPU RAM Your machine supports the following Windows operating systems. REQUIREMENT (RECOMMENDED) OPERATING SYSTEM CPU RAM Pentium II 400 MHz (Pentium III 933 MHz) 64 MB (128 MB) 600 MB Windows XP Pentium III 933 MHz (Pentium IV 1 GHz) 128 MB (256 MB) 1.5 GB Windows Server 2003 Pentium III 933 MHz (Pentium IV 1 GHz) 128 MB (512 MB) 1.
SETTING UP THE NETWORK You need to set up the network protocols on the machine (;printer) to use it in the network environment. If you use your machine in the wired network, refer to 'Using a wired network'. If you use your network printer in the wireless network, refer to "Using a wireless network(Windows/CLX-3175FW only)" on page 27.
Starting the program 1. Connect your machine and the computer using crossover network cable. 2. Temporarily disable the computer firewall before continuing by doing the following: Macintosh OS Windows XP • Open System • Open Control Panel. Preferences. • Double click Security • Click Sharing. Center. • Click the Firewall menu. • Click Windows Firewall. • Turn firewall off. • Disable the firewall. 3. From the Windows Start menu, select All Programs > Samsung Network Printer Utilities > SetIP > SetIP. 4.
USING A WIRELESS NETWORK(WINDOWS/CLX3175FW ONLY) You must set up the network protocols on your machine to use it on your network. This chapter will show you how this is easily accomplished. This section is applicable only for the Windows operating system. Before starting, please locate the USB cable and the Printer Software Installation CD-ROM provided with your machine (;printer).
9. The window shows the wireless network setting and check if settings are right. Click Next. • For the DHCP method If the IP address assignment method is DHCP, check if DHCP is shown in the window. However, if it shows Static, click Change TCP/ IP to change the assignment method to DHCP. • For the Static method If the IP address assignment method is Static, check if Static is shown in the window.
static address.If computer is configured IP address as 192.168.1.100, Subnet address as 255.255.255.0 and Gateway address as 192.168.1.1, input IP address as 192.168.1.101, Subnet address as 255.255.255.0 and Gateway address as 192.168.1.1 on your printer. values for the printer. Before entering the IP address for the printer, you must know the computerís network configuration information. If the computer is set to DHCP, you must contact the network administrator to get the static IP address.
assign the IP address and set other network parameters. • If you know that you are connecting to an Infrastructure mode network with an access point, and the IP address is assigned by a DHCP server, you may proceed to the Configuring the machine’s wireless network part after reviewing the following parts on printing a Network Configuration Report.
6. Follow the instructions in the window and complete the installation. • Starting the program 1. Connect your machine and the computer using crossover network cable. 2. Temporarily disable the computer firewall before continuing by doing the following: Windows XP Macintosh OS • Open Control Panel. • Open System • Double click Security Preferences. Center. • Click Sharing. • Click Windows Firewall. • Click the Firewall menu. • Disable the firewall. • Turn firewall off. 3.
suggested by IEEE 802.11 standard for security. Static WEP security mode requires a proper WEP key for data encryption, decryption, and IEEE 802.11 authentication. Press the left/right arrow to select the setup method you want in Authentication and press OK. 4. Press the left/right arrow to select the setup method you want appears and press OK. • Wizard: The wireless network interface card in your printer searches for wireless networks in the area and shows the results.
3. Click Wireless and Select Wizard. Then, click Next. Wizard will help you setup the wireless network configuration. However, if you want to set the wireless network directly, select Custom. 5. Click Next. If wireless security setting window appears, enter the registered password (network key) and click Next. 4. Select the one Network Name(SSID) in the list. 6. Wizard Setup Confirmation window appears, please check your wireless setup. If the setup is right, click Apply. 7. Click OK.
• If the installation window does not appear, click Start > Run. Type X:\Setup.exe, replacing “X” with the letter which represents your drive and click OK. • If you use Windows vista, Windows 7 and Windows Server 2008 R2, click Start > All Programs > Accessories > Run, and type X:\Setup.exe. The installation window may slightly differ, if you are reinstalling the driver. 3. Select Typical installation for a network printer, and then click Next. 4. The list of machines available on the network appears.
MACHINE'S BASIC SETTINGS After installation is complete, you may want to set the machine's default settings. Refer to the next section if you would like to set or change values. Altitude adjustment The print quality is affected by atmospheric pressure, which is determined by the height of the machine above sea level. The following information will guide you on how to set your machine to the best print quality or best quality of print.
Comm. which means “Common,” the speaker is on until the remote machine answers. You can adjust the volume level using On Hook Dial. • Ringer: Adjusts the ringer volume. For the ringer volume, you can select Off, Low, Mid, and High. Speaker, ringer, key sound, and alarm sound 1. Press Menu until System Setup appears on the bottom line of the display and press OK. 2. Press the left/right arrow until Sound/Volume appears and press OK. 3.
loading originals and print media This chapter introduces you how to load originals and print media into your machine. This chapter includes: • • • Loading originals Selecting print media Changing the size of the paper in the paper tray LOADING ORIGINALS You can use the scanner glass or ADF to load an original for copying, scanning, and sending a fax. On the scanner glass Make sure that no originals are in the ADF.
2. Load the original face up into the ADF. Make sure that the bottom of the original stack matches the paper size marked on the document input tray. 3. Adjust the document width guides to the paper size. SELECTING PRINT MEDIA You can print on a variety of print media, such as plain paper, envelopes, labels, and transparencies. Always use print media that meet the guidelines for use with your machine.
Specifications on print media TYPE SIZE DIMENSIONS Letter 216 x 279 mm (8.5 x 11 inches) Legal 216 x 356 mm (8.5 x 14 inches) US Folio 216 x 330 mm (8.5 x 13 inches) A4 210 x 297 mm (8.26 x 11.69 inches) Oficio 216 x 343 mm (8.5 x 13.5 inches) JIS B5 182 x 257 mm (7.16 x 10.11 inches) ISO B5 176 x 250 mm (6.93 x 9.84 inches) Executive 184 x 267 mm (7.25 x 10.5 inches) Statement 140 x 216 mm (5.5 x 8.5 inches) A5 148 x 210 mm (5.82 x 8.26 inches) A6 105 x 148 mm (4.13 x 5.
Media sizes supported in each mode MODE SIZE MEDIA TYPE SOURCE Copy mode Letter, A4, Legal, Oficio, US Folio, Executive, JIS B5, A5, A6 tray 1 Print mode All sizes supported by the machine tray 1 Fax mode Letter, A4, Legal tray 1 Envelopes • • Guidelines for special print media MEDIA TYPE Envelopes (Continue) GUIDELINES • Labels • GUIDELINES • • • • • • Successful printing on envelopes depends upon the quality of the envelopes.
MEDIA TYPE Preprinted paper GUIDELINES • • • • Letterhead must be printed with heat-resistant ink that will not melt, vaporize, or release hazardous emissions when subjected to the printer’s fusing temperature for 0.1 second. Check your machine’s specification to view the fusing temperature, see "General specifications" on page 88. Letterhead ink must be non-flammable and should not adversely affect printer rollers.
6. Slide the tray 1 back into the machine. 7. After loading paper, set the paper type and size for the tray. See "Setting the paper size and type" on page 43. • • • Due to insufficient paper in the tray, the paper length guide can be pushed to inside, load enough paper. If you experience problems with paper feed, load a paper into the tray one by one. You can load previously printed paper. The printed side should be facing up with an uncurled edge at the front.
PRINTING ON SPECIAL PRINT MATERIALS SETTING THE PAPER SIZE AND TYPE The machine can hold special sizes and types of print material, such as postcards, note cards, and envelopes. Especially, it is useful for single page printing on letterhead or colored paper. After loading paper in the paper tray, you need to set the paper size and type using the control panel buttons. These settings will apply to Copy and Fax modes.
copying This chapter gives you step-by-step instructions for copying documents. This chapter includes: • • • Copying Changing the settings for each copy Changing the default copy settings COPYING 1. Press Copy. Ready to Copy appears on the top line of the display. 2. Load originals face up into the ADF, or place a single original face down on the scanner glass. For details about loading an original. (See "Loading originals" on page 37.) 3. Enter the number of copies using the number keypad, if necessary.
While you are setting copy options, pressing Stop/Clear cancels the changed settings and restores the defaults. ID CARD COPYING Your machine can print 2-sided originals on one sheet of A4-, Letter-, Legal, Folio-, Oficio-, Executive-, B5-, A5-, or A6-sized paper. The machine prints one side of the original on the upper half of the paper and the other side on the lower half without reducing the size of the original. This feature is helpful for copying a small-sized item, such as a business card.
5. Press Stop/Clear to return to ready mode. Your original is divided into 9 portions. Each portion is scanned and printed one by one in the following order: Clone copying Your machine can print multiple image copies from the original document on a single page. The number of images is automatically determined by the original image and paper size. This copy feature is available only when you place originals on the scanner glass. 1. Press Copy. 2.
scanning Scanning with your machine lets you turn pictures and text into digital files that can be stored on your computer. This chapter includes: • • • Scanning basics Scanning from the control panel Scanning by a network connection The maximum resolution that can be achieved depends upon various factors, including computer speed, available disk space, memory, the size of the image being scanned, and bit depth settings.
5. Press the left/right arrow until Local PC appears on the bottom line of the display and press OK. If the machine connected to a network, select Network PC and press OK. If you see Not Available message, check the port connection. If you selected Network PC, select your registered user ID and enter the PIN. Press OK. • ID is the same ID as the registered ID for Samsung Scan Manager. • PIN is the 4 digit number registered for Samsung Scan Manager. 6.
10. Press the left/right arrow until the file format you want appears and press OK or Start. The machine begins scanning and then sends the email. 11. If the machine asks if you want to log off your account, press the left/ right arrow to select Yes or No and press OK. 12. Press Stop/Clear to return to ready mode. CHANGING THE SETTINGS FOR EACH SCAN JOB Your machine provides you with the following setting options to allow you to customize your scan jobs. • Scan Size: Sets the image size.
Searching with a particular first letter 1. If necessary, press Scan/Email. 2. Press Address Book until Search & Send appears on the bottom line of the display and press OK. 3. Press the left/right arrow until the number category you want appears and press OK. 4. Press the left/right arrow until ID appears and press OK. 5. Enter the first few letters of the name you want and press OK. 6. Press the left/right arrow until the name you want appears and press OK.
basic printing This chapter explains common printing tasks. This chapter includes: • Printing a document • Canceling a print job PRINTING A DOCUMENT Your machine allows you to print from various Windows, Macintosh, or Linux applications. The exact steps for printing a document may vary depending on the application you use. For details about printing, see Software section.
faxing This chapter gives you information about using your machine as a fax machine. This chapter includes: • • Sending a fax Receiving a fax • Fax setup Adjusting the document settings We recommend you to use traditional analog phone services (PSTN: public switched telephone network) when connecting telephone lines to use Fax. If you use other Internet services (DSL, ISDN, VoIP), you can improve the connection quality by using the Micro-filter.
Darkness Confirming a transmission You can select the default contrast mode to fax your originals lighter or darker. 1. Press Fax. 2. Press Menu, and then OK when Fax Feature appears on the bottom line of the display. 3. Press OK when Darkness appears. 4. Press the left/right arrow until the option you want appears and press OK. 5. Press Stop/Clear to return to ready mode. When the last page of your original has been sent successfully, the machine beeps and returns to ready mode.
9. When you have finished entering fax numbers, press the left/right arrow to select No at the Another No.? prompt and press OK. The original is scanned into memory before transmission. The display shows memory capacity and the number of pages being stored in memory. 10. If an original is placed on the scanner glass, select Yes to add another pages. Load another original and press OK. When you have finished, select No at the Another Page? prompt.
RECEIVING A FAX Changing receiving modes 1. Press Fax. 2. Press Menu until Fax Setup appears on the bottom line of the display and press OK. 3. Press the left/right arrow until Receiving appears and press OK. 4. Press OK when Receive Mode appears. 5. Press the left/right arrow until the fax reception mode you want appears. • In Fax mode, the machine answers an incoming fax call and immediately goes into the fax reception mode.
6. When your machine begins to ring, do not answer the call. The machine requires several rings to learn the pattern. When the machine completes learning, the display shows Completed DRPD Setup. If the DRPD setup fails, Error DRPD Ring appears. Press OK when DRPD Mode appears and start over from step 4. 7. Press Stop/Clear to return to ready mode. • • DRPD must be set up again if you re-assign your fax number, or connect the machine to another telephone line.
Forwarding received faxes to email address You can set your machine to forward incoming faxes to the email address you entered. 1. Press Fax. 2. Press Menu until Fax Feature appears on the bottom line of the display and press OK. 3. Press the left/right arrow until Forward appears and press OK. 4. Press the left/right arrow until E-mail appears and press OK. 5. Press the left/right arrow until Rcv. Forward appears and press OK. 6. Press the left/right arrow until Forward appears and press OK.
OPTION Discard Size DESCRIPTION When receiving a fax containing pages as long as or longer than the paper in your machine, you can set the machine to discard a specific length from the end of the received fax. The machine will print the received fax on one or more sheets of paper, minus the data that would have been on the specified discard segment.
Enter a speed dial number and press OK. Press OK when speed dial information appears correctly. Press OK when Yes appears. Repeat steps 5 and 6 to include other speed dial numbers into the group. 10. When you have finished, press the left/right arrow to select No at the Another No.? prompt and press OK. 11. Press Stop/Clear to return to ready mode. 6. 7. 8. 9. Editing a group dial number You can delete a specific entry from a group or add a new number to the selected group. 1.
using USB memory device This chapter explains how to use a USB memory device with your machine. This chapter includes: • • • • About USB memory Plugging in a USB memory device Scanning to a USB memory device Printing from a USB memory device ABOUT USB MEMORY USB memory devices are available with a variety of memory capacities to give you more room for storing documents, presentations, downloaded music and videos, high resolution photographs, or whatever other files you want to store or move.
SCANNING TO A USB MEMORY DEVICE You can scan a document and save the scanned image onto a USB memory device. There are two ways of doing this: you can scan to the device using the default settings, or you can customize your own scan settings. • If your USB memory device has certain features (example, security key, security partition, booting disk, password settings and so forth), do not use the USB memory device with your machine.
BACKING UP DATA Data in the machine’s memory can be accidentally erased due to power failure or storage failure. Backup helps you protect your Address Book entries and the system settings by storing them as backup files on a USB memory device. Backing up data 1. Insert the USB memory device into the USB memory port on your machine. 2. Press Menu until System Setup appears on the bottom line of the display and press OK. 3. Press OK when Machine Setup appears. 4.
maintenance This chapter provides information for maintaining your machine and the toner cartridge. This chapter includes: • • • • • • • • • • Printing reports Clearing memory Cleaning your machine Maintaining the cartridge Replacing the toner cartridge PRINTING REPORTS REPORT/LIST Your machine can provide various reports with useful information you will need. The following reports are available: Some reports may not appear in the display depending on options or models.
CLEARING MEMORY CLEANING YOUR MACHINE You can selectively clear information stored in your machine’s memory. For CLX-3170FN/CLX-3175FN/CLX-3175FW users, before clearing the memory, make sure that all fax jobs have been completed, or you will lose those jobs. To maintain print and scan quality, follow the cleaning procedures below each time the toner cartridge is replaced or if print and scan quality problems occur. 1. Press Menu until System Setup appears on the bottom line of the display and press OK.
4. Pull the waste toner container out of the machine using its handle. 7. Holding the groove on the front of the imaging unit, push imaging unit in to the machine. 5. Pull the imaging unit out of the machine using the groove on the front of the imaging unit. 8. Insert the waste toner container into position and then push it to make sure that it is firmly seated in place. • • • Do not touch the green surface, the imaging unit with your hands or any other material.
7. Push the ADF sheet back into the machine smoothly. Cleaning the scan unit Keeping the scan unit clean helps ensure the best possible copies. We suggest that you clean the scan unit at the start of each day and during the day, as needed. 1. Slightly dampen a soft lint-free cloth or paper towel with water. 2. Open the scanner lid. 3. Wipe the surface of the scanner glass until it is clean and dry. 1 2 3 4 White sheet ADF Sheet Scanner glass Scanner lid 4.
MAINTAINING THE CARTRIDGE 1. Using the handle, completely open the front cover. Toner cartridge storage Toner cartridges contain components that are sensitive to light, temperature, and humidity. Samsung suggests users follow the recommendations to ensure the optimum performance, highest quality, and longest life from your new Samsung toner cartridge. Store this cartridge in the same environment as the printer it will be used in; this should be in controlled office temperature and humidity conditions.
4. Slide four toner cartridges back into the machine. 4. Take a new toner cartridge out of its package. • Don't use sharp objects, such as a knife or scissors, to open the toner cartridge package. You could damage the surface of the toner cartridge. 5. Holding both handles on the toner cartridge, thoroughly rock it from side to side to evenly distribute the toner. 5. Close the front cover. Make sure the cover is securely latched.
REPLACING THE IMAGING UNIT When the life span of the imaging unit has expired, the Smart Panel program window appears on the computer, indicating the imaging unit needs to be replaced. Otherwise your machine stops printing. 1. Turn the machine off, then wait a few minutes for the machine to cool. 2. Using the handle, completely open the front cover. 5. Pull the imaging unit out of the machine using the groove on the front of the imaging unit. 6. Take a new imaging unit out of its package.
8. Insert the waste toner container into position and then push it to make sure that it is firmly seated in place. REPLACING THE WASTE TONER CONTAINER When the life span of the waste toner container has expired, the Smart Panel program window appears on the computer, indicating the waste toner container needs to be replaced. Otherwise your machine stops printing. 1. Turn the machine off, then wait a few minutes for the machine to cool. 2. Using the handle, completely open the front cover. 9.
6. Insert the new container into position and then push it to make sure that it is firmly seated in place. Supplies Info: Prints the supply information page. Total: Displays the total number of pages printed. ADF Scan: Displays the number of pages scanned using the ADF. Platen Scan: Displays the number of pages scanned using the scanner glass. • Imaging Unit, Transfer Belt, Fuser, TransferRoller, Tray1 Roller: displays the number of pages printed each item. 5.
troubleshooting This chapter gives helpful information for what to do if you encounter an error. This chapter includes: • • • Tips for avoiding paper jams Clearing document jams Clearing paper jams • • Understanding display messages Solving other problems 3. Pull the jammed paper gently out of the ADF. TIPS FOR AVOIDING PAPER JAMS By selecting the correct media types, most paper jams can be avoided. When a paper jam occurs, follow the steps outlined on page 72. • Follow the procedures on page 42.
Roller misfeed In the tray 1 1. Open the scanner lid. 2. Seize the misfeed paper, and remove the paper from the feed area by carefully pulling it to the right using both hands. 1. Open and close the front cover. The jammed paper is automatically ejected from the machine. If the paper does not exit, go to the next step. 2. Pull the tray 1 out of the machine. 3. Remove the jammed paper by gently pulling it straight out. 3. Close the scanner lid. Then load the removed pages back into the ADF.
2. Open the inner cover. In the paper exit area 1. Open and close the front cover. The jammed paper is automatically ejected from the machine. 2. Gently pull the paper out of the output tray. 3. Carefully take the jammed paper out of the machine. If you do not see the jammed paper or if there is any resistance when you pull, stop and go to the next step. 3. Open the rear cover. 4. If you see the jammed paper, pull it straight up. Skip to step 8. Do not touch the fuser inside the inner cover.
6. Open the scan unit. 9. Pull down the fuser lever. 7. Carefully take the jammed paper out of the machine. 10. Close the rear cover. Printing automatically resumes. 8. Lowering down the scan unit gently and slowly until it is completely closed. Make sure that it is securely latched.
UNDERSTANDING DISPLAY MESSAGES Messages appear on the control panel display to indicate the machine’s status or errors. Refer to the tables below to understand the messages’ meaning and correct the problem if necessary. Messages and their meanings are listed in alphabetical order. • • • MESSAGE MEANING SUGGESTED SOLUTIONS ADC Not Confirm Error A problem has occurred in the ADC in the machine. Turn the power switch off and on. If the problem persists, call for service.
MESSAGE Memory Full MEANING The memory is full. SUGGESTED SOLUTIONS SUGGESTED SOLUTIONS Paper Jam 0 Open/Close Door Paper has jammed in the feeding area of the tray. Clear the jam. (See "In the tray 1" on page 73.) Paper Jam 1 Check Inside Paper has jammed in the paper exit area. Clear the jam. (See "In the fuser unit area" on page 73.) Paper Jam 2 Check Inside Paper has jammed In the fuser area or around the toner cartridge Clear the jam. (See "In the paper exit area" on page 74.
MESSAGE MEANING SUGGESTED SOLUTIONS Send Error (POP3) There is a problem in POP3. Configure the POP3 setting. Send Error (SMTP) There is a problem in SMTP. Change to the available server. Send Error (Wrong Config) There is a problem on the network interface card. Configure your network interface card correctly. [Stop Pressed] Stop/Clear has been pressed during an operation. Try again. Toner Empty T A toner cartridge has almost reached its estimated cartridge life.
SOLVING OTHER PROBLEMS The following chart lists some conditions that may occur and the recommended solutions. Follow the suggested solutions until the problem is corrected. If the problem persists, call for service Printing problems CONDITION The machine does not print. Paper feeding CONDITION POSSIBLE CAUSE SUGGESTED SOLUTIONS The machine is not receiving power. Check the power cord connections. Check the power switch and the power source.
POSSIBLE CAUSE CONDITION The machine selects print materials from the wrong paper source. The paper source selection in the printer properties may be incorrect. CONDITION For many software applications, the paper source selection is found under the Thin Paper tab within the printer properties. Select the correct paper source. See the printer driver help screen. The printer does not print PDF file correctly. Some parts of graphics, text, or illustrations are missing.
CONDITION Dropouts AaBbCc AaBbCc AaBbCc AaBbCc AaBbCc White Spots Vertical lines Color or Black background Toner smear SUGGESTED SOLUTIONS If faded areas, generally rounded, occur randomly on the page: • A single sheet of paper may be defective. Try reprinting the job. • The moisture content of the paper is uneven or the paper has moist spots on its surface. Try a different brand of paper. (See "Selecting print media" on page 38.) • The paper lot is bad.
CONDITION Curl or wave SUGGESTED SOLUTIONS • • • Wrinkles or creases • • • Back of printouts are dirty Solid Color or Black pages • • • A Loose toner • Ensure that the paper is loaded properly. Check the paper type and quality. Both high temperature and humidity can cause paper curl. (See "Selecting print media" on page 38.) Turn over the stack of paper in the tray. Also try rotating the paper 180° in the tray. Ensure that the paper is loaded properly. Check the paper type and quality.
CONDITION SUGGESTED SOLUTIONS Blank copies print out. Ensure that the original is face down on the scanner glass or face up in the ADF. Image rubs off the copy easily. • Frequent copy paper jams occur. • • • • Toner cartridge produces fewer copies than expected before running out of toner. • • • Replace the paper in the tray with paper from a new package. In high humidity areas, do not leave paper in the machine for extended periods of time.
Fax problems CONDITION CONDITION SUGGESTED SOLUTIONS The machine is not working, there is no display and the buttons are not working. • • Unplug the power cord and plug it in again. Ensure that there is power to the electrical outlet. No dial tone sounds. • Check that the phone line is connected properly. Check that the phone socket in the wall is working by plugging in another phone. • The numbers stored in memory do not dial correctly. Make sure that the numbers are stored in memory correctly.
Common Linux problems CONDITION The machine does not print. SUGGESTED SOLUTIONS • • • • • Some color images come out all black. Check if the printer driver is installed in your system. Open Unified Driver configurator and switch to the Printers tab in Printers configuration window to look at the list of available printers. Make sure that your machine is displayed on the list. If not, invoke Add new printer wizard to set up your device. Check if the printer is started.
CONDITION The machine does not appear on the scanners list. SUGGESTED SOLUTIONS • • • Check if your machine is attached to your computer. Make sure that it is connected properly via the USB port and is turned on. Check if the scanner driver for your machine is installed in your system. Open Unified Driver configurator, switch to Scanners configuration, then press Drivers. Make sure that driver with a name corresponding to your machine's name is listed in the window. Check if the port is not busy.
ordering supplies This chapter provides information on purchasing cartridges and accessories available for your machine. This chapter includes: • Supplies • The optional parts or features may differ by countries. Contact your sales representatives whether the part you want is available in your country. SUPPLIES How to purchase HOW TO PURCHASE To order Samsung-authorized supplies or accessories, contact your local Samsung dealer or the retailer where you purchased your machine, or visit www.samsung.
specifications This chapter guides you about this machine’s specifications such as various features. This chapter include: • • • General specifications Printer specifications Scanner specifications • • GENERAL SPECIFICATIONS The symbol * optional feature depending on machines. ITEM DESCRIPTION Copier specifications Facsimile specifications ITEM DESCRIPTION Waste toner containerd Approx. 10,000 images Memory 128 MB (Non extendable) External dimension (W x D x H) 415 x 373 x 342 mm (16.3 x 14.
PRINTER SPECIFICATIONS ITEM Printing method Printing speeda First print out time ITEM DESCRIPTION Color laser beam printing • • Black & White: Up to 16 ppm (A4), 17 ppm (Letter) Color: Up to 4 ppm(A4), 4 ppm (Letter) Black & White • • From ready: Less than 14 seconds From coldboot: Less than 45 seconds Color • • From ready: Less than 26 seconds From coldboot: Less than 57 seconds Print resolution Max.
FACSIMILE SPECIFICATIONS The fax feature may not be supported depending on machines. ITEM DESCRIPTION Compatibility ITU-T G3 Applicable line Public Switched Telephone Network (PSTN) or behind PABX Data coding MH/MR/MMR/JBIG/JPEG Modem speed 33.
glossary The following glossary helps you get familiar with the product by understanding the terminologies commonly used with printing as well as mentioned in this user's guide. ADF An Automatic Document Feeder (ADF) is a mechanism that will automatically feed an original sheet of paper so that the machine can scan some amount of the paper at once. AppleTalk AppleTalk is a proprietary suite of protocols developed by Apple, Inc for computer networking.
An emulator duplicates the functions of one system with a different system, so that the second system behaves like the first system. Emulation focuses on exact reproduction of external behavior, which is in contrast to simulation, which concerns an abstract model of the system being simulated, often considering its internal state.
LED PABX A Light-Emitting Diode (LED) is a semiconductor device that indicates the status of a machine. A private automatic branch exchange (PABX) is an automatic telephone switching system within a private enterprise. MAC address PCL Media Access Control (MAC) address is a unique identifier associated with a network adapter. MAC address is a unique 48-bit identifier usually written as 12 hexadecimal characters grouped in pairs (e. g., 00-00-0c34-11-4e).
Subnet Mask The subnet mask is used in conjunction with the network address to determine which part of the address is the network address and which part is the host address. TCP/IP The Transmission Control Protocol (TCP) and the Internet Protocol (IP); the set of communications protocols that implement the protocol stack on which the Internet and most commercial networks run.
index loading originals 57 A Address Book group dial numbers 60 speed dial numbers 60 Address Book, use 51 ADF 39 scanner glass 39 E Erasing background, special copy 48 machine ID, set 54 ADF 20 F ADF, load 39 fax header, set 54 adjustment Fax mode, receiving mode 57 altitude 37 alarm sound 38 Ans/Fax mode, receiving mode 57 faxing Multiple Send faxes 55 default settings, change 60 delayed faxes 56 fax setup 59 forwarding faxes 58 Multiple Send faxes 55 priority faxes 56 receiving faxes 57 s
problem, solve copying 84 faxing 86 Linux 87 Network Scan 85 paper feeding 81 printing quality 82 scanning 85 Windows 86 R tray adjusting the width and length 43 U USB flash memory data backup 64 managing 64 printing 63 scanning 63 using receiving a fax in Ans/Fax mode 57 in DRPD mode 57 in Fax mode 57 in Secure Receiving mode 58 in Tel mode 57 SetIP 27 V volume, adjust ringer 38 speaker 38 receiving modes 57 redialing automatically 55 manually 55 replacing components toner cartridge 70 reports, p
contact samsung worldwide If you have any comments or questions regarding Samsung products, contact the Samsung customer care center. COUNTRY/REG ION CUSTOMER CARE CENTER WEB SITE ARGENTINE 0800-333-3733 www.samsung.com/ar AUSTRALIA 1300 362 603 www.samsung.com/au AUSTRIA 0810-SAMSUNG (7267864, € 0.07/min) www.samsung.com/at BELARUS 810-800-500-55-500 www.samsung/ua www.samsung.com/ua_ru BELGIUM 02 201 2418 www.samsung.com/be (Dutch) www.samsung.
COUNTRY/REG ION CUSTOMER CARE CENTER WEB SITE RUSSIA 8-800-555-55-55 www.samsung.ru SINGAPORE 1800-SAMSUNG (726-7864) www.samsung.com/sg SLOVAKIA 0800-SAMSUNG (726-7864) www.samsung.com/sk SOUTH AFRICA 0860 SAMSUNG (726-7864) www.samsung.com/za SPAIN 902-1-SAMSUNG(902 172 678) www.samsung.com/es SWEDEN 0771 726 7864 (SAMSUNG) www.samsung.com/se SWITZERLAND 0848-SAMSUNG (7267864, CHF 0.08/min) www.samsung.com/ch TADJIKISTAN 8-10-800-500-55-500 TAIWAN 0800-329-999 www.samsung.
features of your new laser product Your new machine is equipped with a number of special features that improve the quality of the documents you print. With the machine, you can: SPECIAL FEATURES Print with excellent quality and speed • You can print in a full range of colors using cyan, magenta, yellow, and black. • You can print with a resolution of up to 2400 x 600 dpi. See Software section. • Your machine prints A4-sized paper at up to 16 ppm and letter-sized paper at up to 17 ppm.
FEATURES BY MODELS The machine is designed to support all of your document needs – from printing and copying, to more advanced networking solutions for your business. Basic features of this machine include: FEATURES CLX-3175 CLX-3175N USB 2.
FINDING MORE INFORMATION You can find information for setting up and using your machine from the following resources, either as a print-out or onscreen. Quick Install Guide Provides information on setting up your machine and this requires that you follow the instructions in the guide to prepare the machine.
5
safety information IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS What the icons and signs in this user’s guide mean: Hazards or unsafe practices that may result in severe personal injury or death. WARNING Hazards or unsafe practices that may result in minor personal injury or property damage. CAUTION CAUTION To reduce the risk of fire, explosion, electric shock, or personal injury when using your laser MFP, follow these basic safety precautions: Do NOT attempt. Do NOT disassemble. Do NOT touch.
13. Unplug the machine from the telephone jack, PC and AC wall outlet and refer servicing to qualified service personnel under the following conditions: • When any part of the power cord, plug or connecting cable is damaged or frayed. • If liquid has been spilled into the machine. • If the machine has been exposed to rain or water. • If the machine does not operate properly after instructions have been followed. • If the machine has been dropped, or the cabinet appears damaged.
OZONE SAFETY During normal operation, this machine produces ozone. The ozone produced does not present a hazard to the operator. However, it is advisable that the machine be operated in a well ventilated area. If you need additional information about ozone, request your nearest Samsung dealer. MERCURY SAFETY Contains Mercury, Dispose According to Local, State or Federal Laws.(U.S.A.
RADIO FREQUENCY EMISSIONS FCC Information to the User This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
FAX BRANDING The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone facsimile machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission the following information: (1) the date and time of transmission (2) identification of either business, business entity or individual sending the message; and (3) telephone number of ei
REPLACING THE FITTED PLUG (FOR UK ONLY) Important The mains lead for this machine is fitted with a standard (BS 1363) 13 amp plug and has a 13 amp fuse. When you change or examine the fuse, you must re-fit the correct 13 amp fuse. You then need to replace the fuse cover. If you have lost the fuse cover, do not use the plug until you have another fuse cover. Contact the people from you purchased the machine. The 13 amp plug is the most widely used type in the UK and should be suitable.
European Radio Approval Information (for products fitted with EU-approved radio devices) Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz/5 GHz band, may be present (embedded) in your printer system which is intended for home or office use. This section is only applicable if these devices are present. Refer to the system label to verify the presence of wireless devices.
REGULATORY COMPLIANCE STATEMENTS Wireless Guidance Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz/5 GHz Band, may be present (embedded) in your printer system. The following section is a general overview of considerations while operating a wireless device. Additional limitations, cautions, and concerns for specific countries are listed in the specific country sections (or country group sections).
OPENSSL LICENSE Copyright (c) 1998-2001 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
contents 2 6 INTRODUCTION 18 GETTING STARTED 23 LOADING ORIGINALS AND PRINT MEDIA 28 COPYING 34 15_Contents Features of your new laser product Safety information 18 18 18 19 20 20 21 22 22 22 Machine overview Front view Rear view Control panel overview Understanding the Status LED Acknowledging the status of the toner cartridge Menu overview Supplied software Printer driver features Printer driver 23 24 24 24 24 25 25 25 25 26 27 27 27 27 27 27 Setting up the hardware System requirements Windo
contents SCANNING 37 BASIC PRINTING 40 USING USB MEMORY DEVICE 41 MAINTENANCE 44 36 36 36 Erasing background images Gray enhance copying Setting copy timeout 37 37 37 37 38 38 38 Scanning basics Scanning from the control panel Setting scan information in Samsung Scan Manager.
contents TROUBLESHOOTING 52 ORDERING SUPPLIES 65 SPECIFICATIONS 66 GLOSSARY 68 INDEX 72 17_Contents 51 51 To access SyncThru™ Web Service: Checking the machine’s serial number 52 52 52 52 53 55 57 57 57 58 61 61 62 62 64 Tips for avoiding paper jams Clearing paper jams In the tray 1 In the fuser unit area In the paper exit area Understanding display messages Solving other problems Paper feeding Printing problems Printing quality problems Copying problems Scanning problems Common Windows problems
introduction These are the main components of your machine: This chapter includes: • • • • Machine overview Control panel overview Understanding the Status LED Acknowledging the status of the toner cartridge • • • Menu overview Supplied software Printer driver features MACHINE OVERVIEW Front view Rear view 1 Network porta 4 Power receptacle 2 USB port 5 Rear cover 3 Handle 6 Power switch a. CLX-3175N only.
CONTROL PANEL OVERVIEW Display Shows the current status and prompts during an operation. 2 Toner colors The toner colors shown below the LCD display co-works with the display messages. See Status LED with the toner cartridge messages. (See "Acknowledging the status of the toner cartridge" on page 20.) 3 Status Shows the status of your machine. (See "Understanding the Status LED" on page 20.) 4 Menu Enters Menu mode and scrolls through the available menus.
UNDERSTANDING THE STATUS LED The color of the Status LED indicates the machine's current status. STATUS DESCRIPTION • • Off • Green Blinking • • Red The machine is powered off-line. The machine is in power save mode. When data is received, or any button is pressed, it switches to on-line automatically. Wireless function can not be used. • The machine is powered on and can be used. Blinking • A minor error has occurred and the machine is waiting for the error to be cleared.
MENU OVERVIEW The control panel provides access to various menus to set up the machine or use the machine’s functions. These menus can be accessed by pressing Menu. Refer to the following diagram. Some menus may not appear in the display depending on options or models. If so, it is not applicable to your machine. . Copy Feature Reduce/Enlarge Darkness Original Type Layout Adjust Bkgd.
SUPPLIED SOFTWARE PRINTER DRIVER FEATURES After you have set up your machine and connected it to your computer, you must install the printer software. If you are a Windows or Macintosh OS, install the software from the supplied CD and if you are a Linux OS user, download the software from the Samsung website (www.samsung.com/ printer) and install.
getting started This chapter gives you step-by-step instructions for setting up the machine. This chapter includes: • • • Setting up the hardware System requirements Setting up the network (CLX-3175N only) • • Installing the software Machine's basic settings SETTING UP THE HARDWARE 3. 4. 5. 6. Remove the tape holding the machine tightly. Load paper. Make sure that all the cables are connected to the machine. Turn the machine on.
SYSTEM REQUIREMENTS Macintosh Before you begin, ensure that your system meets the following requirements: REQUIREMENT (RECOMMENDED) OPERATING SYSTEM Windows CPU FREE HDD SPACE RAM Your machine supports the following Windows operating systems. REQUIREMENT (RECOMMENDED) OPERATING SYSTEM CPU RAM Pentium II 400 MHz (Pentium III 933 MHz) 64 MB (128 MB) 600 MB Windows XP Pentium III 933 MHz (Pentium IV 1 GHz) 128 MB (256 MB) 1.
SETTING UP THE NETWORK (CLX-3175N ONLY) You need to set up the network protocols on the machine to use it in the network environment. You can set up the basic network settings through the machine's control panel. Supported operating environments The following table shows the network environments supported by the machine: ITEM REQUIREMENTS Network interface • Ethernet 10/100 Base-TX Network operating system • • • Windows 2000/XP/2003/2008/Vista/7/ Server 2008 R2 Various Linux OS MAC OS 10.3 ~ 10.
INSTALLING THE SOFTWARE 5. Select Typical installation for a network printer, and then click Next. You have to install the machine software for printing. The software includes drivers, applications, and other user friendly programs. The following procedure is based on Windows XP. If you use Macintosh or Linux OS, see Software section. • • The following procedure is for when the machine is being used as a network machine. If you want to connect a machine with a USB cable, refer to Software section.
MACHINE'S BASIC SETTINGS Key sound, and alarm sound After installation is complete, you may want to set the machine's default settings. Refer to the next section if you would like to set or change values. Altitude adjustment The print quality is affected by atmospheric pressure, which is determined by the height of the machine above sea level. The following information will guide you on how to set your machine to the best print quality or best quality of print.
loading originals and print media This chapter introduces you how to load originals and print media into your machine. This chapter includes: • • • Loading originals Selecting print media Changing the size of the paper in the paper tray LOADING ORIGINALS • • Printing on special print materials Setting the paper size and type 3. Close the scanner lid. You can use the scanner glass to load an original for copying and scanning. • • On the scanner glass • 1. Lift and open the scanner lid.
Specifications on print media TYPE SIZE DIMENSIONS Letter 216 x 279 mm (8.5 x 11 inches) Legal 216 x 356 mm (8.5 x 14 inches) US Folio 216 x 330 mm (8.5 x 13 inches) A4 210 x 297 mm (8.26 x 11.69 inches) Oficio 216 x 343 mm (8.5 x 13.5 inches) JIS B5 182 x 257 mm (7.16 x 10.11 inches) ISO B5 176 x 250 mm (6.93 x 9.84 inches) Executive 184 x 267 mm (7.25 x 10.5 inches) Statement 140 x 216 mm (5.5 x 8.5 inches) A5 148 x 210 mm (5.82 x 8.26 inches) A6 105 x 148 mm (4.13 x 5.
Media sizes supported in each mode MODE SIZE MEDIA TYPE SOURCE Copy mode Letter, A4, Legal, Oficio, US Folio, Executive, JIS B5, A5, A6 tray 1 Print mode All sizes supported by the machine tray 1 Envelopes (Continue) Envelopes • GUIDELINES • • • • • • • • Guidelines for special print media MEDIA TYPE GUIDELINES Labels Successful printing on envelopes depends upon the quality of the envelopes.
MEDIA TYPE Preprinted paper GUIDELINES • • • • Letterhead must be printed with heat-resistant ink that will not melt, vaporize, or release hazardous emissions when subjected to the printer’s fusing temperature for 0.1 second. Check your machine’s specification to view the fusing temperature, see "General specifications" on page 66. Letterhead ink must be non-flammable and should not adversely affect printer rollers.
6. Slide the tray 1 back into the machine. 7. After loading paper, set the paper type and size for the tray. See "Setting the paper size and type" on page 33. • • • Due to insufficient paper in the tray, the paper length guide can be pushed to inside, load enough paper. If you experience problems with paper feed, load a paper into the tray one by one. You can load previously printed paper. The printed side should be facing up with an uncurled edge at the front.
PRINTING ON SPECIAL PRINT MATERIALS SETTING THE PAPER SIZE AND TYPE The machine can hold special sizes and types of print material, such as postcards, note cards, and envelopes. Especially, it is useful for single page printing on letterhead or colored paper. After loading paper in the paper tray, you need to set the paper size and type using the control panel buttons. These settings will apply to Copy mode.
copying This chapter gives you step-by-step instructions for copying documents. This chapter includes: • • • Copying Changing the settings for each copy Changing the default copy settings • • Using special copy features Setting copy timeout COPYING Original Type 1. Place a single original face down on the scanner glass. For details about loading an original. (See "Loading originals" on page 28.) 2. Enter the number of copies using the left/right arrow, if necessary. 3.
While you are setting copy options, pressing Stop/Clear cancels the changed settings and restores the defaults. ID CARD COPYING Your machine can print 2-sided originals on one sheet of A4-, Letter-, Folio, Oficio-, Executive-, B5-, A5-, or A6-sized paper. The machine prints one side of the original on the upper half of the paper and the other side on the lower half without reducing the size of the original. This feature is helpful for copying a small-sized item, such as a business card.
6. Press Stop/Clear to return to ready mode. Your original is divided into 9 portions. Each portion is scanned and printed one by one in the following order: Clone copying Your machine can print multiple image copies from the original document on a single page. The number of images is automatically determined by the original image and paper size. This copy feature is available only when you place originals on the scanner glass. 1. Press Menu. 2. Press OK when Copy Menu appears. 3.
scanning Scanning with your machine lets you turn pictures and text into digital files that can be stored on your computer. This chapter includes: • • Scanning basics Scanning from the control panel The maximum resolution that can be achieved depends upon various factors, including computer speed, available disk space, memory, the size of the image being scanned, and bit depth settings.
5. Press the left/right arrow until Local PC appears on the bottom line of the display and press OK. If the machine connected to a network, select Network PC and press OK. If you see Not Available message, check the port connection. If you selected Network PC, select your registered user ID and enter the PIN. Press OK. • ID is the same ID as the registered ID for Samsung Scan Manager. • PIN is the 4 digit number registered for Samsung Scan Manager. 6.
39 _Scanning
basic printing This chapter explains common printing tasks. This chapter includes: • Printing a document • Canceling a print job PRINTING A DOCUMENT Your machine allows you to print from various Windows, Macintosh, or Linux applications. The exact steps for printing a document may vary depending on the application you use. For details about printing, see Software section.
using USB memory device This chapter explains how to use a USB memory device with your machine. This chapter includes: • • • • About USB memory Plugging in a USB memory device Scanning to a USB memory device Printing from a USB memory device ABOUT USB MEMORY USB memory devices are available with a variety of memory capacities to give you more room for storing documents, presentations, downloaded music and videos, high resolution photographs, or whatever other files you want to store or move.
4. Press OK when Scan to USB appears on the bottom line of the display. 5. Press Color Start or Black Start when Ready to Scan to USB appears. Regardless of the button you press, the color mode is decided as customized. (See “Customizing Scan to USB” on page 42.) Your machine begins scanning the original, and then asks if you want to scan another page. 6. Press OK when Yes appears to scan more pages. Load an original and press Color Start or Black Start.
7. Press the left/right arrow until the file containing the data you want to restore appears and press OK. 8. Press OK when Yes appears to restore the backup file to the machine. 9. Press Stop/Clear to return to ready mode. MANAGING USB MEMORY You can delete image files stored on a USB memory device one by one or all at once by reformatting the device. After deleting files or reformatting a USB memory device, files cannot be restored. Therefore, confirm that you no longer need the data before deleting it.
maintenance This chapter provides information for maintaining your machine and the toner cartridge. This chapter includes: • • • • • • • • • • Printing reports Clearing memory Cleaning your machine Maintaining the cartridge Replacing the toner cartridge 7. Press Stop/Clear to return to ready mode. PRINTING REPORTS Your machine can provide various reports with useful information you will need. The following reports are available: Some reports may not appear in the display depending on options or models.
CLEANING YOUR MACHINE 4. Pull the waste toner container out of the machine using its handle. To maintain print and scan quality, follow the cleaning procedures below each time the toner cartridge is replaced or if print and scan quality problems occur. • • Cleaning the cabinet of the machine with cleaning materials containing large amounts of alcohol, solvent, or other strong substances can discolor or distort the cabinet.
7. Holding the groove on the front of the imaging unit, push imaging unit in to the machine. Cleaning the scan unit Keeping the scan unit clean helps ensure the best possible copies. We suggest that you clean the scan unit at the start of each day and during the day, as needed. 1. Slightly dampen a soft lint-free cloth or paper towel with water. 2. Open the scanner lid. 3. Wipe the surface of the scanner glass until it is clean and dry. 8.
MAINTAINING THE CARTRIDGE 1. Using the handle, completely open the front cover. Toner cartridge storage Toner cartridges contain components that are sensitive to light, temperature, and humidity. Samsung suggests users follow the recommendations to ensure the optimum performance, highest quality, and longest life from your new Samsung toner cartridge. Store this cartridge in the same environment as the printer it will be used in; this should be in controlled office temperature and humidity conditions.
4. Slide four toner cartridges back into the machine. 4. Take a new toner cartridge out of its package. • Don't use sharp objects, such as a knife or scissors, to open the toner cartridge package. You could damage the surface of the toner cartridge. 5. Holding both handles on the toner cartridge, thoroughly rock it from side to side to evenly distribute the toner. 5. Close the front cover. Make sure the cover is securely latched.
REPLACING THE IMAGING UNIT When the life span of the imaging unit has expired, the Smart Panel program window appears on the computer, indicating the imaging unit needs to be replaced. Otherwise your machine stops printing. 1. Turn the machine off, then wait a few minutes for the machine to cool. 2. Using the handle, completely open the front cover. 5. Pull the imaging unit out of the machine using the groove on the front of the imaging unit. 6. Take a new imaging unit out of its package.
8. Insert the waste toner container into position and then push it to make sure that it is firmly seated in place. REPLACING THE WASTE TONER CONTAINER When the life span of the waste toner container has expired, the Smart Panel program window appears on the computer, indicating the waste toner container needs to be replaced. Otherwise your machine stops printing. 1. Turn the machine off, then wait a few minutes for the machine to cool. 2. Using the handle, completely open the front cover. 9.
6. Insert the new container into position and then push it to make sure that it is firmly seated in place. Supplies Info: Prints the supply information page. Total: Displays the total number of pages printed. Platen Scan: Displays the number of pages scanned using the scanner glass. • Imaging Unit, Transfer Belt, Fuser, TransferRoller, Tray1 Roller: displays the number of pages printed each item. 6. If you selected to print a supply information page, press OK to confirm. 7.
troubleshooting This chapter gives helpful information for what to do if you encounter an error. This chapter includes: • • Tips for avoiding paper jams Clearing paper jams • • TIPS FOR AVOIDING PAPER JAMS Understanding display messages Solving other problems In the tray 1 By selecting the correct media types, most paper jams can be avoided. When a paper jam occurs, follow the steps outlined on page 52. • Follow the procedures on page 32. Ensure that the adjustable guides are positioned correctly.
1. Open the scan unit. 5. Lowering down the scan unit gently and slowly until it is completely closed. Make sure that it is securely latched. Be careful not to pinch your fingers! 2. Open the inner cover. If the scan unit is not completely closed, the machine will not operate. In the paper exit area 1. Open and close the front cover. The jammed paper is automatically ejected from the machine. 2. Gently pull the paper out of the output tray. 3. Carefully take the jammed paper out of the machine.
8. Lowering down the scan unit gently and slowly until it is completely closed. Make sure that it is securely latched. Be careful not to pinch your fingers! 5. Pull up the fuser lever. 1 fuser lever 6. Open the scan unit. 9. Pull down the fuser lever. 7. Carefully take the jammed paper out of the machine. 10. Close the rear cover. Printing automatically resumes.
UNDERSTANDING DISPLAY MESSAGES Messages appear on the control panel display to indicate the machine’s status or errors. Refer to the tables below to understand the messages’ meaning and correct the problem if necessary. Messages and their meanings are listed in alphabetical order. • • • If the message is not in the table, cycle the power and try the job again. If the problem persists, call for service.
MESSAGE MEANING SUGGESTED SOLUTIONS Paper Jam 2 Check Inside Paper has jammed In the fuser area or around the toner cartridge Clear the jam. (See "In the paper exit area" on page 53.) Refilled Toner T The toner cartridge you have installed is not genuine or refilled. The arrow indicates which color toner cartridge. The print quality may get poor if the refilled toner cartridge is installed, since its characteristics may significantly differ from the genuine.
SOLVING OTHER PROBLEMS The following chart lists some conditions that may occur and the recommended solutions. Follow the suggested solutions until the problem is corrected. If the problem persists, call for service. Printing problems CONDITION The machine does not print. Paper feeding CONDITION POSSIBLE CAUSE SUGGESTED SOLUTIONS The machine is not receiving power. Check the power cord connections. Check the power switch and the power source.
CONDITION The machine selects print materials from the wrong paper source. POSSIBLE CAUSE The paper source selection in the printer properties may be incorrect. CONDITION For many software applications, the paper source selection is found under the Thin Paper tab within the printer properties. Select the correct paper source. See the printer driver help screen. The printer does not print PDF file correctly. Some parts of graphics, text, or illustrations are missing.
CONDITION Dropouts AaBbCc AaBbCc AaBbCc AaBbCc AaBbCc White Spots Vertical lines Color or Black background Toner smear SUGGESTED SOLUTIONS If faded areas, generally rounded, occur randomly on the page: • A single sheet of paper may be defective. Try reprinting the job. • The moisture content of the paper is uneven or the paper has moist spots on its surface. Try a different brand of paper. (See "Selecting print media" on page 28.) • The paper lot is bad.
CONDITION Curl or wave SUGGESTED SOLUTIONS • • • Wrinkles or creases • • • Back of printouts are dirty Solid Color or Black pages • • • A Loose toner • • • • • Ensure that the paper is loaded properly. Check the paper type and quality. Both high temperature and humidity can cause paper curl. (See "Selecting print media" on page 28.) Turn over the stack of paper in the tray. Also try rotating the paper 180° in the tray. Ensure that the paper is loaded properly. Check the paper type and quality.
Copying problems CONDITION Scanning problems SUGGESTED SOLUTIONS Copies are too light or too dark. Use Darkness to darken or lighten the background of the copies. Smears, lines, marks, or spots appears on copies. • Copy image is skewed. • • • Image rubs off the copy easily. • • • • Toner cartridge produces fewer copies than expected before running out of toner. • • • 61 _Troubleshooting Replace the paper in the tray with paper from a new package.
Common Windows problems CONDITION SUGGESTED SOLUTIONS “File in Use” message appears during installation. Exit all software applications. Remove all software from the StartUp Group, then restart Windows. Reinstall the printer driver. “General Protection Fault”, “Exception OE”, “Spool32”, or “Illegal Operation” messages appear. Close all other applications, reboot Windows and try printing again. “Fail To Print”, “A printer timeout error occurred.” messages appear.
CONDITION Some color images come out in unexpected color. SUGGESTED SOLUTIONS This is a known bug in Ghostscript (until GNU Ghostscript version 7.xx) when the base color space of the document is indexed RGB color space and it is converted through CIE color space. Because Postscript uses CIE color space for Color Matching System, you should upgrade Ghostscript on your system to at least GNU Ghostscript version 8.xx or later. You can find recent Ghostscript versions at www.ghostscript.com.
CONDITION The machine does not scan. SUGGESTED SOLUTIONS • • • Check if a document is loaded into the machine. Check if your machine is connected to the computer. Make sure if it is connected properly if I/O error is reported while scanning. Check if the port is not busy. Since functional components of MFP (printer and scanner) share the same I/O interface (port), the situation of simultaneous access of different “consumer” application to the same port is possible.
ordering supplies This chapter provides information on purchasing cartridges and accessories available for your machine. This chapter includes: • Supplies • The optional parts or features may differ by countries. Contact your sales representatives whether the part you want is available in your country. SUPPLIES How to purchase HOW TO PURCHASE To order Samsung-authorized supplies or accessories, contact your local Samsung dealer or the retailer where you purchased your machine, or visit www.samsung.
specifications This chapter guides you about this machine’s specifications such as various features. This chapter include: • • General specifications Printer specifications • • GENERAL SPECIFICATIONS The symbol * optional feature depending on machines. ITEM DESCRIPTION Scanner specifications Copier specifications ITEM DESCRIPTION External dimension (W x D x H) 415 x 360 x 311 mm (16.3 x 14.2 x 12.2 inches) Tray: 150 sheets for plain paper, 75 g/m2 (20 lb bond) Weight (Including consumables) 14.
PRINTER SPECIFICATIONS ITEM Printing method Printing speeda First print out time ITEM DESCRIPTION Color laser beam printing • • Black & White: Up to 16 ppm (A4), 17 ppm (Letter) Color: Up to 4 ppm(A4), 4 ppm (Letter) Black & White • • From ready: Less than 14 seconds From coldboot: Less than 45 seconds Color • • From ready: Less than 26 seconds From coldboot: Less than 57 seconds Print resolution Max.
glossary The following glossary helps you get familiar with the product by understanding the terminologies commonly used with printing as well as mentioned in this user's guide. ADF An Automatic Document Feeder (ADF) is a mechanism that will automatically feed an original sheet of paper so that the machine can scan some amount of the paper at once. AppleTalk AppleTalk is a proprietary suite of protocols developed by Apple, Inc for computer networking.
An emulator duplicates the functions of one system with a different system, so that the second system behaves like the first system. Emulation focuses on exact reproduction of external behavior, which is in contrast to simulation, which concerns an abstract model of the system being simulated, often considering its internal state.
LED PABX A Light-Emitting Diode (LED) is a semiconductor device that indicates the status of a machine. A private automatic branch exchange (PABX) is an automatic telephone switching system within a private enterprise. MAC address PCL Media Access Control (MAC) address is a unique identifier associated with a network adapter. MAC address is a unique 48-bit identifier usually written as 12 hexadecimal characters grouped in pairs (e. g., 00-00-0c34-11-4e).
Subnet Mask The subnet mask is used in conjunction with the network address to determine which part of the address is the network address and which part is the host address. TCP/IP The Transmission Control Protocol (TCP) and the Internet Protocol (IP); the set of communications protocols that implement the protocol stack on which the Internet and most commercial networks run.
index A adjustment K R key sound 28 replacing components altitude 28 alarm sound 28 toner cartridge 48 reports, print 44 L LED B ringer 28 Status 21 background image, adjust 37 Linux problems 62 S loading originals scanner glass C scanner glass 29 cleaning inside 45 outside 45 scan unit 46 2-up, 4-up 36 clone 37 darkness 35 default setting, change 36 erasing background 37 ID card copy 36 original type 35 poster 36 time out, set 37 scanning M maintenance parts 51 toner cartridge 47 mem
contact samsung worldwide If you have any comments or questions regarding Samsung products, contact the Samsung customer care center. COUNTRY/REG ION CUSTOMER CARE CENTER WEB SITE ARGENTINE 0800-333-3733 www.samsung.com/ar AUSTRALIA 1300 362 603 www.samsung.com/au AUSTRIA 0810-SAMSUNG (7267864, € 0.07/min) www.samsung.com/at BELARUS 810-800-500-55-500 www.samsung/ua www.samsung.com/ua_ru BELGIUM 02 201 2418 www.samsung.com/be (Dutch) www.samsung.
COUNTRY/REG ION CUSTOMER CARE CENTER WEB SITE RUSSIA 8-800-555-55-55 www.samsung.ru SINGAPORE 1800-SAMSUNG (726-7864) www.samsung.com/sg SLOVAKIA 0800-SAMSUNG (726-7864) www.samsung.com/sk SOUTH AFRICA 0860 SAMSUNG (726-7864) www.samsung.com/za SPAIN 902-1-SAMSUNG(902 172 678) www.samsung.com/es SWEDEN 0771 726 7864 (SAMSUNG) www.samsung.com/se SWITZERLAND 0848-SAMSUNG (7267864, CHF 0.08/min) www.samsung.com/ch TADJIKISTAN 8-10-800-500-55-500 TAIWAN 0800-329-999 www.samsung.
© 2008 Samsung Electronics Co., Ltd. All rights reserved. This user’s guide is provided for information purposes only. All information included herein is subject to change without notice. Samsung Electronics is not responsible for any direct or indirect damages, arising from or related to use of this user’s guide. • • • • • • Samsung and Samsung logo are trademarks of Samsung Electronics Co., Ltd.
REV 3.
Samsung Printer Software section
SOFTWARE SECTION CONTENTS Chapter 1: INSTALLING PRINTER SOFTWARE IN WINDOWS Installing Printer Software ........................................................................................................ 4 Installing Software for Local Printing ................................................................................. 4 Installing Software for Network Printing ............................................................................. 7 Reinstalling Printer Software .....................
Fitting Your Document to a Selected Paper Size ......................................................................... 19 Using Watermarks ................................................................................................................. 20 Using an Existing Watermark ......................................................................................... 20 Creating a Watermark ...................................................................................................
Chapter 7: USING YOUR PRINTER IN LINUX Getting Started ..................................................................................................................... 28 Installing the Unified Linux Driver ............................................................................................ 28 Installing the Unified Linux Driver ................................................................................... 28 Uninstalling the Unified Linux Driver .......................................
1 Installing Printer Software in Windows 1 Make sure that the printer is connected to your computer and powered on. 2 Insert the supplied CD-ROM into your CD-ROM drive. The CD-ROM should automatically run, and an installation window appears. This chapter includes: If the installation window does not appear, click Start and then Run. Type X:\Setup.exe, replacing “X” with the letter which represents your drive and click OK.
NOTE: If your printer is not already connected to the computer, the following window will appear. NOTE: After setup is complete, if your printer driver doesn’t work properly, reinstall the printer driver. See “Reinstalling Printer Software” on page 10. Custom Installation You can choose individual components to install. 1 Make sure that the printer is connected to your computer and powered on. 2 Insert the supplied CD-ROM into your CD-ROM drive.
4 Select Custom installation. Click Next. • The installation window that appears in this User’s Guide may differ depending on the printer and interface in use. 6 5 Select the components to be installed and click Next. Select your printer and click Next. NOTE: You can change the desired installation folder by clicking [Browse]. 7 After the installation is finished, a window asking you to print a test page appears. If you choose to print a test page, select the checkbox and click Next.
Installing Software for Network Printing 4 Select Typical installation for a network printer. Click Next. 5 The list of printers available on the network appears. Select the printer you want to install from the list and then click Next. When you connect your printer to a network, you must first configure the TCP/IP settings for the printer. After you have assigned and verified the TCP/IP settings, you are ready to install the software on each computer on the network.
6 After the installation is finished, a window appears asking you to print a test page and to register yourself as a user of Samsung Printers in order to receive information from Samsung. If you so desire, select the corresponding checkbox(es) and click Finish. 3 Click Next. Otherwise, just click Finish. • If necessary, select a language from the drop-down list. 4 Select Custom installation. Click Next. 5 The list of printers available on the network appears.
network, enter the port name and the IP address for the printer. the network, set the printer as the default printer, and change the port name of each printer. Click Next. To verify your printer’s IP address or the MAC address, print a Network Configuration page. • To find a shared network printer (UNC Path), select Shared Printer [UNC] and enter the shared name manually or find a shared printer by clicking the Browse button.
Reinstalling Printer Software NOTE: If your printer is not already connected to the computer, the following window will appear. You can reinstall the software if installation fails. 1 Start Windows. 2 3 4 From the Start menu select Programs or All Programs → your printer driver name → Maintenance. Select Repair and click Next. The list of printers available on the network appears. Select the printer you want to install from the list and then click Next. • After connecting the printer, click Next.
Removing Printer Software 1 2 3 4 5 6 Start Windows. From the Start menu select Programs or All Programs → your printer driver name → Maintenance. Select Remove and click Next. You will see a component list so that you can remove any item individually. Select the components you want to remove and then click Next. When your computer asks you to confirm your selection, click Yes. The selected driver and all of its components are removed from your computer. After the software is removed, click Finish.
2 Basic Printing 1 Open the document you want to print. 2 Select Print from the File menu. The Print window is displayed. It may look slightly different depending on your application. this chapter explains the printing options and common printing tasks in windows. The basic print settings are selected within the Print window. These settings include the number of copies and print range.
Printing to a file (PRN) Printer Settings You will sometimes need to save the print data as a file for your purpose. You can use the printer properties window, which allows you to access all of the printer options you need when using your printer. When the printer properties are displayed, you can review and change the settings needed for your print job. To create a file: 1 Check the Print to file box at the Print window. Your printer properties window may differ, depending on your operating system.
Layout Tab Paper Tab The Layout tab provides options to adjust how the document appears on the printed page. The Layout Options includes Multiple Pages per Side, Poster Printing and Booklet Printing. See “Printing a Document” on page 12 for more information on accessing printer properties. Use the following options to set the basic paper handling specifications when you access the printer properties. See “Printing a Document” on page 12 for more information on accessing printer properties.
Color Paper: 20 lb to 24 lb (75~90 g/m2) color-backgrounded paper. Archive Paper: If you need to keep print-out for a long period time such as archives, select this option. • Color Adjust : You can adjust the appearance of images by changing the settings in the Levels option. • Color Matching : You can adjust the appearance of images by changing the settings in the Settings option. Scaling Printing Advanced Options Scaling Printing allows you to automatically or manually scale your print job on a page.
Extras Tab About Tab You can select output options for your document. See “Printing a Document” on page 12 for more information about accessing the printer properties. Use the About tab to display the copyright notice and the version number of the driver. If you have an Internet browser, you can connect to the Internet by clicking on the web site icon. See “Printing a Document” on page 12 for more information about accessing printer properties.
3 Advanced Printing Printing Multiple Pages on One Sheet of Paper (N-Up Printing) This chapter explains printing options and advanced printing tasks. 1 2 3 4 NOTE: • Your printer driver Properties window that appears in this User’s Guide may differ depending on the printer in use. However the composition of the printer properties window is similar. • If you need to know the exact name of your printer, you can check the supplied CD-ROM.
Printing Posters Printing Booklets This feature allows you to print a single-page document onto 4, 9, or 16 sheets of paper, for the purpose of pasting the sheets together to form one poster-size document. 1 To change the print settings from your software application, access printer properties. See “Printing a Document” on page 12. 2 Click the Layout tab, select Poster Printing in the Layout Type drop-down list.
Printing on Both Sides of Paper Printing a Reduced or Enlarged Document You can print on both sides of a sheet of paper. Before printing, decide how you want your document oriented. You can change the size of a page’s content to appear larger or smaller on the printed page. The options are: • None • Long Edge, which is the conventional layout used in book binding. • Short Edge, which is the type often used with calendars.
Editing a Watermark Using Watermarks 1 To change the print settings from your software application, access printer properties. See “Printing a Document” on page 12. 2 Click the Extras tab and click the Edit button in the Watermark section. The Edit Watermark window appears. 3 Using an Existing Watermark Select the watermark you want to edit from the Current Watermarks list and change the watermark message and options. 4 Click Update to save the changes.
Using a Page Overlay Using Overlays After an overlay has been created, it is ready to be printed with your document. To print an overlay with a document: What is an Overlay? Dear ABC Regards WORLD BEST An overlay is text and/or images stored in the computer hard disk drive (HDD) as a special file format that can be printed on any document. Overlays are often used to take the place of preprinted forms and letterhead paper.
4 Sharing the Printer Locally Setting Up a Host Computer You can connect the printer directly to a selected computer, which is called “host computer,” on the network. The following procedure is for Windows XP. For other Windows OS, refer to the corresponding Windows User's Guide or online help. NOTES: • Check the Operating System(s) that are compatible with your printer. Please refer to the OS Compatibility section of Printer Specifications in your Printer User’s Guide.
5 Scanning Scanning with your machine lets you turn pictures and text into digital files on your computer. Then you can fax or e-mail the files, display them on your web site or use them to create projects that you can print using Samsung SmarThru software or the WIA driver. Scanning Using Samsung SmarThru Samsung SmarThru is the accompanying software for your machine. With SmarThru, scanning is the proverbial piece of cake.
The SmarThru 4 window opens. NOTE: To send an image by e-mail, you must have a mail client program, like Outlook Express, which has been set up with your e-mail account. Make sure that your printer is selected. •Folder Scanning an image and saving it to a folder. Allows you to scan an image, preview it, and save it to the folder of your choice. •Scan To •OCR Allows you to scan an image and save it to an application or folder, email it, or publish it on a web site.
Scanning Process with TWAINenabled Software If you want to scan documents using other software, you will need to use TWAIN-compliant software, such as Adobe Photoshop. The first time you scan with your machine, select it as your TWAIN source in the application you use. 4 Choose your scanning preferences and click Preview to see how your preferences affect the picture. 5 Click Next. 6 Enter a picture name, and select a file format and destination to save the picture.
6 If you are a Windows user, from the Start menu, select Programs or All Programs → your printer driver name → Smart Panel. Using Smart Panel Smart Panel is a program that monitors and informs you of the status of the printer, and allows you to customize the printer’s settings. If you are a Windows or Macintosh OS user, Smart Panel is installed automatically when you install the printer software. If you are a Linux OS user, download Smart Panel from the Samsung website (www.samsung.
Driver Setting (Only for Windows) You can use the printer properties window, which allows you to access all of the printer options you need for using your printer. For details, See “Printer Settings” on page 13. Right-click (in Windows or Linux) or click (in Mac OS X) the Smart Panel icon and select Options. Select the settings you want from the Options window. Opening the Troubleshooting Guide Using the troubleshooting guide, you can view solutions for error status problems.
7 Using Your Printer in Linux You can use your machine in a Linux environment. Installing the Unified Linux Driver Installing the Unified Linux Driver This chapter includes: 1 Make sure that you connect your machine to your computer. Turn both the computer and the machine on. 2 When the Administrator Login window appears, type in root in the Login field and enter the system password.
6 When the installation is complete, click Finish. Uninstalling the Unified Linux Driver 1 When the Administrator Login window appears, type in root in the Login field and enter the system password. NOTE: You must log in as a super user (root) to uninstall the printer software. If you are not a super user, ask your system administrator. 2 Click the icon at the bottom of the desktop.
Using SetIP program Using the Unified Driver Configurator This program is for the network IP setting using the MAC address which is the hardware serial number of the network printer card or interface. Especially, it is for the network administrator to set several network IPs at the same time. Unified Linux Driver Configurator is a tool primarily intended for configuring Printer or MFP devices.
Printers Configuration Classes Tab Printers configuration has the two tabs: Printers and Classes. The Classes tab shows a list of available printer classes. Printers Tab You can see the current system’s printer configuration by clicking on the printer icon button on the left side of the Unified Driver Configurator window. Shows all of the printer classes. Switches to Printer configuration. Shows all of the installed printer. Shows the status of the class and the number of printers in the class.
Ports Configuration In this window, you can view the list of available ports, check the status of each port and release a port that is stalled in busy state when its owner is terminated for any reason. Configuring Printer Properties Using the properties window provided by the Printers configuration, you can change the various properties for your machine as a printer. 1 Open the Unified Driver Configurator. If necessary, switch to Printers configuration. Switches to ports configuration.
The following four tabs display at the top of the window. •General - allows you to change the paper size, the paper type, and the orientation of the documents, enables the duplex feature, adds start and end banners, and changes the number of pages per sheet. •Text - allows you to specify the page margins and set the text options, such as spacing or columns. •Graphics - allows you to set image options that are used when printing images/files, such as color options, image size, or image position.
The document is scanned and the image preview appears in the Preview Pane. Scanning a Document You can scan a document using the Unified Driver Configurator window. 1 Double-click the Unified Driver Configurator on your desktop. 2 Click the 3 Select the scanner on the list. button to switch to Scanners Configuration. Drag the pointer to set the image area to be scanned. Click your scanner. 7 Change the scan options in the Image Quality and Scan Area sections.
If you want to edit the scanned image, use the toolbar. For further details about editing an image, see page 35. 10 When you are finished, click Save on the toolbar. Using the Image Manager The Image Manager application provides you with menu commands and tools to edit your scanned image. 11 Select the file directory where you want to save the image and enter the file name. 12 Click Save. Use these tools to edit the image.
Tools Function Allows you to adjust the brightness or contrast of the image, or to invert the image. Shows the properties of the image. For further details about the Image Manager application, refer to the onscreen help.
8 9 The message which warns all application will close on your computer appears, Click Continue. 10 Select Typical installation for a local printer and then click OK. Using Your Printer with a Macintosh NOTE: If you select Typical installation for a network printer, see “Using SetIP program” on page 38 after the installation is finished. Your printer supports Macintosh systems with a built-in USB interface or 10/100 Base-TX network interface card.
Using SetIP program Setting Up the Printer This program is for the network IP setting using the MAC address which is the hardware serial number of the network printer card or interface. Especially, it is for the network administrator to set several network IPs at the same time. Set up for your printer will be different depending on which cable you use to connect the printer to your computer—the network cable or the USB cable.
For a USB-connected 1 Follow the instructions on “Installing Software” on page 37 to install the PPD and Filter files on your computer. 2 Open the Applications folder → Utilities, and Print Setup Utility. • For MAC OS 10.5~10.6, open System Preferences from the Applications folder, and click Printer & Fax. 3 Click Add on the Printer List. • For MAC OS 10.5~10.6, press the “+” icon then a display window will pop up. 4 For MAC OS 10.3, select the USB tab. • For MAC OS 10.
Changing Printer Settings Printing You can use advanced printing features when using your printer. NOTES: • The Macintosh printer’s properties window that appears in this User’s Guide may differ depending on the printer in use. However the composition of the printer properties window is similar. • You can check your printer name in the supplied CDROM. From your Macintosh application, select Print from the File menu.
Graphics The Graphics tab provides options for selecting Quality and Color Mode. Select Graphics form the Presets' drop-down list to access the graphic features. Printing Multiple Pages on One Sheet of Paper You can print more than one page on a single sheet of paper. This feature provides a cost-effective way to print draft pages. 1 From your Macintosh application, select Print from the File menu. 2 Select Layout. ▲ Mac OS 10.4 •Quality: You can select the printing resolution.
For MAC OS X 10.5~10.6: Make sure that Connected checkbox is checked beside your machine in Bonjour Devices. If you want to scan using TWAIN, refer to the MAC OS X 10.4 procedure above. Scanning You can scan docoments using Image Capture program. Macintosh OS offers Image Capture program. Scanning with USB 1 Make sure that your machine and computer are turned on and properly connected to each other. 2 Place a single document face down on the document glass.
SOFTWARE SECTION INDEX A L advanced printing, use 17 Layout properties, set Windows 14 Linux driver, install 28 printer properties 32 printing 33 scanning 34 B booklet printing 18 C canceling scan 25 D document, print Macintosh 40 Windows 12 double-sided printing 19 M Macintosh driver install 37 uninstall 37 printing 40 scanning 42 setting up the printer 38 MFP driver, install Linux 28 E Extras properties, set 16 N F n-up printing Macintosh 41 Windows 17 favorites settings, use 16 G O help,
Linux 34 SmarThru 23 TWAIN 25 WIA driver 25 scanning from Macintosh 42 setting darkness 15 favorites 16 image mode 15 resolution Windows 15 toner save 15 true-type option 15 software install Macintosh 37 Windows 4 reinstall Windows 10 system requirements Macintosh 37 uninstall Macintosh 37 Windows 11 status monitor, use 26 T toner save, set 15 TWAIN, scan 25 U uninstall, software Macintosh 37 Windows 11 uninstalling MFP driver Linux 29 W watermark create 20 delete 20 edit 20 print 20 WIA, scan 25 44
