LCD DISPLAY quick start guide 400DX-3,460DX-3 ii
Introduction Package Contents Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by Check the contents of the holding the grooves on package. both sides of the package box. Remove the Styrofoam and vinyl cover. Note • After unpacking the package, make sure to check the contents of the package. • Store the packaging box in case you need to move the Product later. • If any items are missing, contact your dealer.
Introduction Manuals Quick Setup Guide Warranty Card User's Manual (Not available in all locations) Cables Power Cord D-Sub Cable Others Remote Control Batteries (AAA X 2) (BP59-00138B) (Not available in all locations) Sold separately Semi Stand KIT LAN Cable USB Cable RGB to BNC Cable RGB to COMPONENT Cable Network Box
Introduction Sold separately Wall Mount KIT TV Tuner Box HDMI Cable HDMI-DVI Cable Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values.
Introduction However, the picture may display abnormally if the connected external input signal is different from the selected video signal. • A TV tuner box (sold separately) must be connected to use the TV. • MagicInfo can only be enabled when a network box is connected. PIP button Push the PIP button to turn the PIP screen On / Off.
Introduction POWER S/W ON [ │ ] / OFF Switches the LCD Display On/Off. POWER The power cord plugs into the LCD Display and the wall outlet. IR OUT/IN Receives a signal from the remote control and outputs the signal through Loopout when a removable sensor board is connected. DVI OUT (LOOPOUT) • Connect a monitor to another monitor through a DVI, DVI to HDMI cable. • Connect a DVI or DVI-HDMI cable to [DVI OUT (LOOPOUT)] on the product and [DVI IN] or [HDMI IN] on another monitor.
Introduction • The status of the cable may have a great effect on the Loopout performance. RGB/COMPONENT IN (PC/COMPONENT Connection Terminal (Input)) • Connect the [RGB/COMPONENT IN] port on the monitor to the RGB port on the PC using the D-SUB cable. • Connect the [RGB/COMPONENT IN] port on the monitor to the COMPONENT port on the external device using the RGB to COMPONENT cable. • Connect the [RGB/COMPONENT IN] port on the monitor to the BNC port on the PC using the RGB to BNC cable.
Introduction Connect a headphone or an External speaker. DC OUT Make sure to use connecting [DC OUT] terminal to the authorized TV-Tuner Box [SBB_DTC/ZA]. Otherwise, this may result in damage to the product. HDMI IN 1 • Connect the [HDMI IN 1] terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable. • Up to HDMI 1.3 can be supported. Note • A normal external device (DVD player or camcorder, etc.
Introduction RJ 45 MDC (MDC PORT) MDC(Multiple Display Control) Program Port Connect the LAN cable to [RJ45 MDC] on the product and LAN on the PC. To use an MDC, the MDC program must be installed on the PC. Note Go to Multi Control and select RJ45 MDC as the MDC Connection. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port Connect a serial cable (cross type) to [RS232C] on the product and RS232C on the PC. To use an MDC, the MDC program must be installed on the PC.
Introduction 3. Insert the Kensington Lock into the security slot ( play. 4. ) on the back of the dis- Lock the lock ( ). Note • These are general instructions. For exact instructions, see the User Manual supplied with the locking device. • You can purchase the locking device from an electronics store, an online shop, or our service center.
Introduction POWER Connect the [POWER] terminal of the product and the [POWER] terminal of the monitor using a power extension cable. POWER Connects to a mains socket via the power cord. POWER S/W ON [ I ] / OFF Turns the network box on or off. Note The power switches of both of the monitor and the network box must be turned on for the network box to operate normally.
Introduction MENU RETURN EXIT MagicInfo POWER Turns the product On/Off. Turns the product Off. OFF Number Buttons Used to enter the password during the OSD adjustment or to use MagicInfo. Press to change the channel. DEL / GUIDE button The "-" button is used to select Digital channels. Electronic Program Guide (EPG) display. - This function does not work for this LCD Display. Adjusts the audio volume. + VOL SOURCE Selects a connected external input source or MagicInfo mode.
Introduction - This is activated when a TV tuner box is installed. MTS/DUAL MTSYou can select MTS (Multichannel Television Stereo) mode. FM Stereo Audio Type MTS/S_Mode Default Mono Mono Stereo Mono ↔ Stereo Manual Change SAP Mono ↔ SAP Mono DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV. - This is activated when a TV tuner box is installed.
Connections Connecting a Computer There are several ways to connect the computer to the monitor. Choose one from the following options. Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, [RGB/COMPONENT IN] port on the back of your LCD Display and the 15 pin D-sub Port on the computer. Using the DVI (Digital) connector on the video card. • Connect the DVI Cable to the [DVI IN] port on the back of your LCD Display and the DVI port on the computer.
Connections Note Select HDMI2 or HDMI1 as an input source when connected to the PC via an HDMI cable. To obtain normal picture and audio from the PC, HDMI2 or HDMI1 must be selected before PC is selected in Edit Name. To enable audio when DVI Device is selected, be sure to establish the connection using step( ). Connect the Audio cable for your LCD Display to the AUDIO port on the back of the LCD Display. Connect the power cord for your LCD Display to the POWER port on the back of the LCD Display.
Connections Connect between the [DVI OUT(LOOPOUT)] port on the LCD Display and the input port on another monitor using a DVI cable. Connect between the [AUDIO OUT] port on the LCD Display and the audio input port on another monitor using a stereo cable. Note • Select DVI Mode as an input source for the external monitor connected to [DVI OUT]. • DVI OUT does not support HDCP. Connecting AV Devices 1.
Connections Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the [AV IN] on the LCD Display . 2. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV /COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display . 3. Press SOURCE on the product or remote control and select "AV". 4.
Connections Connecting Using a HDMI Cable 1. Connect an HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] on the product and the HDMI output port on a digital device. 2. Press SOURCE on the product or remote control and select "HDMI1 / HDMI2" Note In HDMI mode, only PCM format audio is supported. Connecting Using a DVI to HDMI Cable Connect a DVI-HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] and the DVI output port on the digital device.
Connections Note Press SOURCE on the product or remote control and select "HDMI1 / HDMI2" Connecting a DVD Player Connect a RGB to Component cable between the [RGB/COMPONENT IN] port on the LCD Display and the PR, Y, PB jacks on the DVD player. Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display and the AUDIO OUT jacks on the DVD player. Note • Press SOURCE on the product or remote control and select "Component".
Connections Connect a RGB to Component cable between the [RGB/COMPONENT IN] port on the LCD Display and the PR, Y, PB jacks on the Set Top Box. Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display and the AUDIO OUT jacks on the Set Top Box. Note • Press SOURCE on the product or remote control and select "Component". • For an explanation of Component video, see your Set Top Box owner's manual. Connecting to an Audio System 1.
Connections Connecting the Power Connect the [POWER] terminal of the product and the [POWER] terminal of the installed network box using a power extension cable. Connect the power cord to [POWER] on the network box and mains socket. Turn on the power switch. Connecting to MAGICINFO OUT 1. Connect the [MAGICINFO OUT] terminal of the network box and the [HDMI IN 2 (MAGICINFO)] terminal of the monitor using the HDMI cable.
Connections Connecting a LAN Cable 1. Connect the LAN cable between the [LAN] port on the product and the [LAN] port on your PC. Connecting a USB devices 1. You can connect USB devices such as a mouse or keyboard.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display.
Troubleshooting • Do not use benzene, thinner or other flammable substances. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user is responsible for any damage caused by using these substances. Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer.
Troubleshooting A: Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. Q: The screen is blank and the power indicator is off. A: Ensure that the power cord is firmly connected and the LCD Display is on. (Refer to the Connecting a Computer) Q: "No Signal" message.
Troubleshooting Q: The screen color is inconsistent. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color image is distorted by dark shadows. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color white is poor. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The Power Indicator blinks. A: The LCD Display is currently saving the changes made in the settings to the OSD memory.
Troubleshooting A: Check if a special fluorescent or neon lamp is on in the vicinity. Q: How can I change the frequency? A: The frequency can be changed by reconfiguring the video card. Q&A Note That video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) Q: How can I adjust the resolution? A: Windows XP: Control Panel → Appearance and Themes → Display → Settings.
